The first three non-comment configuration lines are as follows:
.code
-domainlist local_domains = @
+domainlist local_domains = @
domainlist relay_to_domains =
hostlist relay_from_hosts = 127.0.0.1
.endd
fact authenticate until you complete the authenticator definitions.
.code
require message = relay not permitted
- domains = +local_domains : +relay_domains
+ domains = +local_domains : +relay_to_domains
.endd
This statement rejects the address if its domain is neither a local domain nor
one of the domains for which this host is a relay.
.endd
In a list, the syntax is similar. For example:
.code
-domainlist relay_domains = sqlite;/some/thing/sqlitedb \
+domainlist relay_to_domains = sqlite;/some/thing/sqlitedb \
select * from relays where ip='$sender_host_address';
.endd
The only character affected by the &%quote_sqlite%& operator is a single
subject having matched any of the patterns, it is in the set if the last item
was a negative one, but not if it was a positive one. For example, the list in
.code
-domainlist relay_domains = !a.b.c : *.b.c
+domainlist relay_to_domains = !a.b.c : *.b.c
.endd
matches any domain ending in &'.b.c'& except for &'a.b.c'&. Domains that match
neither &'a.b.c'& nor &'*.b.c'& do not match, because the last item in the
list is positive. However, if the setting were
.code
-domainlist relay_domains = !a.b.c
+domainlist relay_to_domains = !a.b.c
.endd
then all domains other than &'a.b.c'& would match because the last item in the
list is negative. In other words, a list that ends with a negative item behaves
respectively. Then there follows the name that you are defining, followed by an
equals sign and the list itself. For example:
.code
-hostlist relay_hosts = 192.168.23.0/24 : my.friend.example
+hostlist relay_from_hosts = 192.168.23.0/24 : my.friend.example
addresslist bad_senders = cdb;/etc/badsenders
.endd
A named list may refer to other named lists:
identifiers, base-36 digits. The number is converted to decimal and output as a
string.
+
.vitem &*${domain:*&<&'string'&>&*}*&
.cindex "domain" "extraction"
.cindex "expansion" "domain extraction"
when &%length%& is used as an operator.
+ .vitem &*${listcount:*&<&'string'&>&*}*&
+ .cindex "expansion" "list item count"
+ .cindex "list" "item count"
+ .cindex "list" "count of items"
+ .cindex "&%listcount%& expansion item"
+ The string is interpreted as a list and the number of items is returned.
+
+
+ .vitem &*${listnamed:*&<&'name'&>&*}*&&~and&~&*${list_*&<&'type'&>&*name'&>&*}*&
+ .cindex "expansion" "named list"
+ .cindex "&%listnamed%& expansion item"
+ The name is interpreted as a named list and the content of the list is returned,
+ expanding any referenced lists, re-quoting as needed for colon-separation.
+ If the optional type if given it must be one of "a", "d", "h" or "l"
+ and selects address-, domain-, host- or localpart- lists to search among respectively.
+ Otherwise all types are searched in an undefined order and the first
+ matching list is returned.
+
+
.vitem &*${local_part:*&<&'string'&>&*}*&
.cindex "expansion" "local part extraction"
.cindex "&%local_part%& expansion item"
. Allow this long option name to split; give it unsplit as a fifth argument
. for the automatic .oindex that is generated by .option.
-.option "smtp_accept_max_per_ &~&~connection" main integer 1000 &&&
+.option "smtp_accept_max_per_connection" main integer 1000 &&&
smtp_accept_max_per_connection
.cindex "SMTP" "limiting incoming message count"
.cindex "limit" "messages per SMTP connection"
In the main part of the configuration, you put the following definitions:
.code
-domainlist local_domains = my.dom1.example : my.dom2.example
-domainlist relay_domains = friend1.example : friend2.example
-hostlist relay_hosts = 192.168.45.0/24
+domainlist local_domains = my.dom1.example : my.dom2.example
+domainlist relay_to_domains = friend1.example : friend2.example
+hostlist relay_from_hosts = 192.168.45.0/24
.endd
Now you can use these definitions in the ACL that is run for every RCPT
command:
.code
acl_check_rcpt:
- accept domains = +local_domains : +relay_domains
- accept hosts = +relay_hosts
+ accept domains = +local_domains : +relay_to_domains
+ accept hosts = +relay_from_hosts
.endd
The first statement accepts any RCPT command that contains an address in
the local or relay domains. For any other domain, control passes to the second