Reset locale after calling embedded Perl, in case it was changed.

[users/jgh/exim.git] / doc / doc-txt / NewStuff

$Cambridge: exim/doc/doc-txt/NewStuff,v 1.20 2004/12/17 14:52:44 ph10 Exp $

New Features in Exim
--------------------

This file contains descriptions of new features that have been added to Exim,
but have not yet made it into the main manual (which is most conveniently
updated when there is a relatively large batch of changes). The doc/ChangeLog
file contains a listing of all changes, including bug fixes.


Version 4.50
------------

 1. There is a new build-time option called CONFIGURE_GROUP which works like
    CONFIGURE_OWNER. It specifies one additional group that is permitted for
    the runtime configuration file when the group write permission is set.

 2. The "control=submission" facility has a new option /sender_retain. This
    has the effect of setting local_sender_retain true and local_from_check
    false for the incoming message in which it is encountered.

 3. $recipients is now available in the predata ACL (oversight).

 4. The value of address_data from a sender verification is now available in
    $sender_address_data in subsequent conditions in the ACL statement. Note:
    this is just like $address_data. The value does not persist after the end
    of the current ACL statement. If you want to preserve it, you can use one
    of the ACL variables.

 5. The redirect router has two new options: forbid_sieve_filter and
    forbid_exim_filter. When filtering is enabled by allow_filter, these
    options control which type(s) of filtering are permitted. By default, both
    Exim and Sieve filters are allowed.

 6. A new option for callouts makes it possible to set a different (usually
    smaller) timeout for making the SMTP connection. The keyword is "connect".
    For example:

       verify = sender/callout=5s,connect=1s

    If not specified, it defaults to the general timeout value.

 7. The new variables $sender_verify_failure and $recipient_verify_failure
    contain information about exactly what failed. In an ACL, after one of
    these failures, the relevant variable contains one of the following words:

      qualify       the address was unqualified (no domain), and the message
                    was neither local nor came from an exempted host;

      route         routing failed;

      mail          routing succeeded, and a callout was attempted; rejection
                    occurred at or before the MAIL command (that is, on initial
                    connection, HELO, or MAIL);

      recipient     the RCPT command in a callout was rejected;

      postmaster    the postmaster check in a callout was rejected.

    The main use of these variables is expected to be to distinguish between
    rejections of MAIL and rejections of RCPT.

 8. The command line option -dd behaves exactly like -d except when used on a
    command that starts a daemon process. In that case, debugging is turned off
    for the subprocesses that the daemon creates. Thus, it is useful for
    monitoring the behaviour of the daemon without creating as much output as
    full debugging.

 9. $host_address is now set to the target address during the checking of
    ignore_target_hosts.

10. There are four new variables called $spool_space, $log_space,
    $spool_inodes, and $log_inodes. The first two contain the amount of free
    space in the disk partitions where Exim has its spool directory and log
    directory, respectively. (When these are in the same partition, the values
    will, of course, be the same.) The second two variables contain the numbers
    of free inodes in the respective partitions.

    NOTE: Because disks can nowadays be very large, the values in the space
    variables are in kilobytes rather than in bytes. Thus, for example, to
    check in an ACL that there is at least 50M free on the spool, you would
    write:

       condition = ${if > {$spool_space}{50000}{yes}{no}}

    The values are recalculated whenever any of these variables is referenced.
    If the relevant file system does not have the concept of inodes, the value
    of those variables is -1. If the operating system does not have the ability
    to find the amount of free space (only true for experimental systems), the
    space value is -1.

11. It is now permitted to omit both strings after an "if" condition; if the
    condition is true, the result is the string "true". As before, when the
    second string is omitted, a false condition yields an empty string. This
    makes it less cumbersome to write custom ACL and router conditions. For
    example, instead of

      condition = ${if eq {$acl_m4}{1}{yes}{no}}

    or the shorter form

      condition = ${if eq {$acl_m4}{1}{yes}}

    (because the second string has always defaulted to ""), you can now write

      condition = ${if eq {$acl_m4}{1}}

    Previously this was a syntax error.

12. There is a new "record type" that can be specified in dnsdb lookups. It
    is "zns" (for "zone NS"). It performs a lookup for NS records on the given
    domain, but if none are found, it removes the first component of the domain
    name, and tries again. This process continues until NS records are found
    or there are no more components left (or there's a DNS error). In other
    words, it may return the name servers for a top-level domain, but it never
    returns the root name servers. If there are no NS records for the top-level
    domain, the lookup fails.

    For example, ${lookup dnsdb{zns=xxx.quercite.com}} returns the name
    servers for quercite.com, whereas ${lookup dnsdb{zns=xxx.edu}} returns
    the name servers for edu, assuming in each case that there are no NS
    records for the full domain name.

    You should be careful about how you use this lookup because, unless the
    top-level domain does not exist, the lookup will always return some host
    names. The sort of use to which this might be put is for seeing if the name
    servers for a given domain are on a blacklist. You can probably assume that
    the name servers for the high-level domains such as .com or .co.uk are not
    going to be on such a list.

13. Another new "record type" is "mxh"; this looks up MX records just as "mx"
    does, but it returns only the names of the hosts, omitting the priority
    values.

14. It is now possible to specify a list of domains or IP addresses to be
    looked up in a dnsdb lookup. The list is specified in the normal Exim way,
    with colon as the default separator, but with the ability to change this.
    For example:

      ${lookup dnsdb{one.domain.com:two.domain.com}}
      ${lookup dnsdb{a=one.host.com:two.host.com}}
      ${lookup dnsdb{ptr = <; 1.2.3.4 ; 4.5.6.8}}

    In order to retain backwards compatibility, there is one special case: if
    the lookup type is PTR and no change of separator is specified, Exim looks
    to see if the rest of the string is precisely one IPv6 address. In this
    case, it does not treat it as a list.

    The data from each lookup is concatenated, with newline separators (by
    default - see 14 below), in the same way that multiple DNS records for a
    single item are handled.

    The dnsdb lookup fails only if all the DNS lookups fail. If there is a
    temporary DNS error for any of them, the remaining lookups are still done,
    and only if none of them succeed does the dnsdb lookup defer. As long as at
    least one of the DNS lookups yields some data, the dnsdb lookup succeeds.

15. It is now possible to specify the character to be used as a separator when
    a dnsdb lookup returns data from more than one DNS record. The default is a
    newline. To specify a different character, put '>' followed by the new
    character at the start of the query. For example:

      ${lookup dnsdb{>: a=h1.test.ex:h2.test.ex}}
      ${lookup dnsdb{>| mxh=<;m1.test.ex;m2.test.ex}}

    It is permitted to specify a space as the separator character. Note that
    more than one DNS record can be found for a single lookup item; this
    feature is relevant even when you do not specify a list.

    The same effect could be achieved by wrapping the lookup in ${tr...}; this
    feature is just a syntactic simplification.

16. It is now possible to supply a list of domains and/or IP addresses to be
    lookup up in a DNS blacklist. Previously, only a single domain name could
    be given, for example:

      dnslists = black.list.tld/$sender_host_name

    What follows the slash can now be a list. As with all lists, the default
    separator is a colon. However, because this is a sublist within the list of
    DNS blacklist domains, it is necessary either to double the separators like
    this:

      dnslists = black.list.tld/name.1::name.2

    or to change the separator character, like this:

      dnslists = black.list.tld/<;name.1;name.2

    If an item in the list is an IP address, it is inverted before the DNS
    blacklist domain is appended. If it is not an IP address, no inversion
    occurs. Consider this condition:

       dnslists = black.list.tls/<;192.168.1.2;a.domain

    The DNS lookups that occur are for

       2.1.168.192.black.list.tld  and  a.domain.black.list.tld

    Once a DNS record has been found (that matches a specific IP return
    address, if specified), no further lookups are done. If there is a
    temporary DNS error, the rest of the sublist of domains or IP addresses is
    tried. The dnslists item itself defers only if none of the other DNS
    lookups in this sublist succeeds. In other words, a successful lookup for
    any of the items in the sublist overrides a defer for a previous item.

17. The log selector queue_time_overall causes Exim to output the time spent on
    the queue as an addition to the "Completed" message. Like queue_time (which
    puts the queue time on individual delivery lines), the time is tagged with
    "QT=", and it is measured from the time that the message starts to be
    received, so it includes the reception time.

18. It is now possible to use both -bF and -bf on the same command, in order to
    test a system filter and a user filter in the same run. For example:

      exim -bF /system/filter -bf /user/filter </test/message

    This is helpful when the system filter adds header lines or sets filter
    variables that are used by the user filter.

19. The Exiscan patch is now merged into the main source. See src/EDITME for
    parameters for the build.


Version 4.43
------------

 1. There is a new Boolean global option called mua_wrapper, defaulting false.
    This causes Exim to run an a restricted mode, in order to provide a very
    specific service.

    Background: On a personal computer, it is a common requirement for all
    email to be sent to a smarthost. There are plenty of MUAs that can be
    configured to operate that way, for all the popular operating systems.
    However, there are MUAs for Unix-like systems that cannot be so configured:
    they submit messages using the command line interface of
    /usr/sbin/sendmail. In addition, utility programs such as cron submit
    messages this way.

    Requirement: The requirement is for something that can provide the
    /usr/sbin/sendmail interface and deliver messages to a smarthost, but not
    provide any queueing or retrying facilities. Furthermore, the delivery to
    the smarthost should be synchronous, so that if it fails, the sending MUA
    is immediately informed. In other words, we want something that in effect
    converts a command-line MUA into a TCP/SMTP MUA.

    Solutions: There are a number of applications (for example, ssmtp) that do
    this job. However, people have found them to be lacking in various ways.
    For instance, some sites want to allow aliasing and forwarding before
    sending to the smarthost.

    Using Exim: Exim already had the necessary infrastructure for doing this
    job. Just a few tweaks were needed to make it behave as required, though it
    is somewhat of an overkill to use a fully-featured MTA for this purpose.

    Setting mua_wrapper=true causes Exim to run in a special mode where it
    assumes that it is being used to "wrap" a command-line MUA in the manner
    just described.

    If you set mua_wrapper=true, you also need to provide a compatible router
    and transport configuration. Typically there will be just one router and
    one transport, sending everything to a smarthost.

    When run in MUA wrapping mode, the behaviour of Exim changes in the
    following ways:

    (a) A daemon cannot be run, nor will Exim accept incoming messages from
        inetd. In other words, the only way to submit messages is via the
        command line.

    (b) Each message is synchonously delivered as soon as it is received (-odi
        is assumed). All queueing options (queue_only, queue_smtp_domains,
        control=queue, control=freeze in an ACL etc.) are quietly ignored. The
        Exim reception process does not finish until the delivery attempt is
        complete. If the delivery was successful, a zero return code is given.

    (c) Address redirection is permitted, but the final routing for all
        addresses must be to the same remote transport, and to the same list of
        hosts. Furthermore, the return_address must be the same for all
        recipients, as must any added or deleted header lines. In other words,
        it must be possible to deliver the message in a single SMTP
        transaction, however many recipients there are.

    (d) If the conditions in (c) are not met, or if routing any address results
        in a failure or defer status, or if Exim is unable to deliver all the
        recipients successfully to one of the hosts immediately, delivery of
        the entire message fails.

    (e) Because no queueing is allowed, all failures are treated as permanent;
        there is no distinction between 4xx and 5xx SMTP response codes from
        the smarthost. Furthermore, because only a single yes/no response can
        be given to the caller, it is not possible to deliver to some
        recipients and not others. If there is an error (temporary or
        permanent) for any recipient, all are failed.

    (f) If more than one host is listed, Exim will try another host after a
        connection failure or a timeout, in the normal way. However, if this
        kind of failure happens for all the hosts, the delivery fails.

    (g) When delivery fails, an error message is written to the standard error
        stream (as well as to Exim's log), and Exim exits to the caller with a
        return code value 1. The message is expunged from Exim's spool files.
        No bounce messages are ever generated.

    (h) No retry data is maintained, and any retry rules are ignored.

    (i) A number of Exim options are overridden: deliver_drop_privilege is
        forced true, max_rcpt in the smtp transport is forced to "unlimited",
        remote_max_parallel is forced to one, and fallback hosts are ignored.

    The overall effect is that Exim makes a single synchronous attempt to
    deliver the message, failing if there is any kind of problem. Because no
    local deliveries are done and no daemon can be run, Exim does not need root
    privilege. It should be possible to run it setuid=exim instead of
    setuid=root. See section 48.3 in the 4.40 manual for a general discussion
    about the advantages and disadvantages of running without root privilege.

 2. There have been problems with DNS servers when SRV records are looked up.
    Some mis-behaving servers return a DNS error or timeout when a non-existent
    SRV record is sought. Similar problems have in the past been reported for
    MX records. The global dns_again_means_nonexist option can help with this
    problem, but it is heavy-handed because it is a global option. There are
    now two new options for the dnslookup router. They are called
    srv_fail_domains and mx_fail_domains. In each case, the value is a domain
    list. If an attempt to look up an SRV or MX record results in a DNS failure
    or "try again" response, and the domain matches the relevant list, Exim
    behaves as if the DNS had responded "no such record". In the case of an SRV
    lookup, this means that the router proceeds to look for MX records; in the
    case of an MX lookup, it proceeds to look for A or AAAA records, unless the
    domain matches mx_domains.

 3. The following functions are now available in the local_scan() API:

    (a) void header_remove(int occurrence, uschar *name)

        This function removes header lines. If "occurrence" is zero or negative,
        all occurrences of the header are removed. If occurrence is greater
        than zero, that particular instance of the header is removed. If no
        header(s) can be found that match the specification, the function does
        nothing.

    (b) BOOL header_testname(header_line *hdr, uschar *name, int length,
                             BOOL notdel)

        This function tests whether the given header has the given name. It
        is not just a string comparison, because whitespace is permitted
        between the name and the colon. If the "notdel" argument is TRUE, a
        FALSE return is forced for all "deleted" headers; otherwise they are
        not treated specially. For example:

           if (header_testname(h, US"X-Spam", 6, TRUE)) ...

    (c) void header_add_at_position(BOOL after, uschar *name, BOOL topnot,
                                    int type, char *format, ...)

        This function adds a new header line at a specified point in the header
        chain. If "name" is NULL, the new header is added at the end of the
        chain if "after" is TRUE, or at the start if "after" is FALSE. If
        "name" is not NULL, the headers are searched for the first non-deleted
        header that matches the name. If one is found, the new header is added
        before it if "after" is FALSE. If "after" is true, the new header is
        added after the found header and any adjacent subsequent ones with the
        same name (even if marked "deleted"). If no matching non-deleted header
        is found, the "topnot" option controls where the header is added. If it
        is TRUE, addition is at the top; otherwise at the bottom. Thus, to add
        a header after all the Received: headers, or at the top if there are no
        Received: headers, you could use

          header_add_at_position(TRUE, US"Received", TRUE, ' ', "X-xxx: ...");

        Normally, there is always at least one non-deleted Received: header,
        but there may not be if received_header_text expands to an empty
        string.

    (d) BOOL receive_remove_recipient(uschar *recipient)

        This is a convenience function to remove a named recipient from the
        list of recipients. It returns TRUE if a recipient was removed, and
        FALSE if no matching recipient could be found. The argument must be a
        complete email address.

 4. When an ACL "warn" statement adds one or more header lines to a message,
    they are added at the end of the existing header lines by default. It is
    now possible to specify that any particular header line should be added
    right at the start (before all the Received: lines) or immediately after
    the first block of Received: lines in the message. This is done by
    specifying :at_start: or :after_received: (or, for completeness, :at_end:)
    before the text of the header line. (Header text cannot start with a colon,
    as there has to be a header name first.) For example:

      warn message = :after_received:X-My-Header: something or other...

    If more than one header is supplied in a single warn statement, each one is
    treated independently and can therefore be placed differently. If you add
    more than one line at the start, or after the Received: block, they will
    end up in reverse order.

    Warning: This facility currently applies only to header lines that are
    added in an ACL. It does NOT work for header lines that are added in a
    system filter or in a router or transport.

 5. There is now a new error code that can be used in retry rules. Its name is
    "rcpt_4xx", and there are three forms. A literal "rcpt_4xx" matches any 4xx
    error received for an outgoing SMTP RCPT command; alternatively, either the
    first or both of the x's can be given as digits, for example: "rcpt_45x" or
    "rcpt_436". If you want (say) to recognize 452 errors given to RCPT
    commands by a particular host, and have only a one-hour retry for them, you
    can set up a retry rule of this form:

      the.host.name  rcpt_452   F,1h,10m

    Naturally, this rule must come before any others that would match.

    These new errors apply to both outgoing SMTP (the smtp transport) and
    outgoing LMTP (either the lmtp transport, or the smtp transport in LMTP
    mode). Note, however, that they apply only to responses to RCPT commands.

 6. The "postmaster" option of the callout feature of address verification has
    been extended to make it possible to use a non-empty MAIL FROM address when
    checking a postmaster address. The new suboption is called "postmaster_
    mailfrom", and you use it like this:

      require  verify = sender/callout=postmaster_mailfrom=abc@x.y.z

    Providing this suboption causes the postmaster check to be done using the
    given address. The original "postmaster" option is equivalent to

      require  verify = sender/callout=postmaster_mailfrom=

    If both suboptions are present, the rightmost one overrides.

    Important notes:

    (1) If you use a non-empty sender address for postmaster checking, there is
        the likelihood that the remote host will itself initiate a callout
        check back to your host to check that address. As this is a "normal"
        callout check, the sender will most probably be empty, thus avoiding
        possible callout loops. However, to be on the safe side it would be
        best to set up your own ACLs so that they do not do sender verification
        checks when the recipient is the address you use for postmaster callout
        checking.

    (2) The caching arrangements for postmaster checking do NOT take account of
        the sender address. It is assumed that either the empty address, or a
        fixed non-empty address will be used. All that Exim remembers is that
        the postmaster check for the domain succeeded or failed.

 7. When verifying addresses in header lines using the verify=header_sender
    option, Exim behaves by default as if the addresses are envelope sender
    addresses from a message. Callout verification therefore tests to see
    whether a bounce message could be delivered, by using an empty address in
    the MAIL FROM command. However, it is arguable that these addresses might
    never be used as envelope senders, and could therefore justifiably reject
    bounce messages (empty senders). There is now an additional callout option
    for verify=header_sender that allows you to specify what address to use in
    the MAIL FROM command. You use it as in this example:

      require  verify = header_sender/callout=mailfrom=abcd@x.y.z

    Important notes:

    (1) As in the case of postmaster_mailfrom (see above), you should think
        about possible loops.

    (2) In this case, as in the case of recipient callouts with non-empty
        senders (the use_sender option), caching is done on the basis of a
        recipient/sender pair.

 8. If you build Exim with USE_READLINE=yes in Local/Makefile, it will try to
    load libreadline dynamically whenever the -be (test expansion) option is
    used without command line arguments. If successful, it will then use
    readline() for reading the test data. A line history is supported. By the
    time Exim does this, it is running as the calling user, so this should not
    cause any security problems. Security is the reason why this is NOT
    supported for -bt or -bv, when Exim is running as root or exim,
    respectively. Note that this option adds to the size of the Exim binary,
    because the dynamic loading library is not otherwise included. On my
    desktop it adds about 2.5K. You may need to add -ldl to EXTRA_LIBS when you
    set USE_READLINE=yes.

 9. Added ${str2b64:<string>} to the expansion operators. This operator
    converts an arbitrary string into one that is base64 encoded.

10. A new authenticator, called cyrus_sasl, has been added. This requires
    the presence of the Cyrus SASL library; it authenticates by calling this
    library, which supports a number of authentication mechanisms, including
    PLAIN and LOGIN, but also several others that Exim does not support
    directly. The code for this authenticator was provided by Matthew
    Byng-Maddick of A L Digital Ltd (http://www.aldigital.co.uk). Here follows
    draft documentation:

                    xx. THE CYRUS_SASL AUTHENTICATOR

    The cyrus_sasl authenticator provides server support for the Cyrus library
    Implementation of the RFC 2222 "Simple Authentication and Security Layer".
    It provides a gatewaying mechanism directly to the Cyrus interface, so if
    your Cyrus library can do, for example, CRAM-MD5, then so can the
    cyrus_sasl authenticator. By default it uses the public name of the driver
    to determine which mechanism to support.

    Where access to some kind of secret file is required, for example in GSSAPI
    or CRAM-MD5, it is worth noting that the authenticator runs as the exim
    user, and that the Cyrus SASL library has no way of escalating privileges
    by default. You may also find you need to set environment variables,
    depending on the driver you are using.

    xx.1 Using cyrus_sasl as a server

    The cyrus_sasl authenticator has four private options. It puts the username
    (on a successful authentication) into $1.

    server_hostname         Type: string*         Default: $primary_hostname

        This option selects the hostname that is used when communicating with
        the library. It is up to the underlying SASL plug-in what it does with
        this data.

    server_mech             Type: string                Default: public_name

        This option selects the authentication mechanism this driver should
        use. It allows you to use a different underlying mechanism from the
        advertised name. For example:

        sasl:
          driver = cyrus_sasl
          public_name = X-ANYTHING
          server_mech = CRAM-MD5
          server_set_id = $1

    server_realm            Type: string                      Default: unset

       This is the SASL realm that the server is claiming to be in.

    server_service          Type: string                      Default: "smtp"

       This is the SASL service that the server claims to implement.

    For straigthforward cases, you do not need to set any of the
    authenticator's private options. All you need to do is to specify an
    appropriate mechanism as the public name. Thus, if you have a SASL library
    that supports CRAM-MD5 and PLAIN, you might have two authenticators as
    follows:

      sasl_cram_md5:
        driver = cyrus_sasl
        public_name = CRAM-MD5
        server_set_id = $1

      sasl_plain:
        driver = cyrus_sasl
        public_name = PLAIN
        server_set_id = $1

11. There is a new global option called tls_on_connect_ports. Its value must be
    a list of port numbers; the most common use is expected to be

      tls_on_connect_ports = 465

    Setting this option has the same effect as -tls-on-connect on the command
    line, but only for the specified ports. It applies to all connections, both
    via the daemon and via inetd. You still need to specify all the ports for
    the daemon (using daemon_smtp_ports or local_interfaces or the -X command
    line option) because this option does not add an extra port -- rather, it
    specifies different behaviour on a port that is defined elsewhere. The
    -tls-on-connect command line option overrides tls_on_connect_ports, and
    forces tls-on-connect for all ports.

12. There is a new ACL that is run when a DATA command is received, before the
    data itself is received. The ACL is defined by acl_smtp_predata. (Compare
    acl_smtp_data, which is run after the data has been received.)
    This new ACL allows a negative response to be given to the DATA command
    itself. Header lines added by MAIL or RCPT ACLs are not visible at this
    time, but any that are defined here are visible when the acl_smtp_data ACL
    is run.

13. The "control=submission" ACL modifier has an option "/domain=xxx" which
    specifies the domain to be used when creating From: or Sender: lines using
    the authenticated id as a local part. If the option is supplied with an
    empty domain, that is, just "/domain=", Exim assumes that the authenticated
    id is a complete email address, and it uses it as is when creating From:
    or Sender: lines.

14. It is now possible to make retry rules that apply only when the failing
    message has a specific sender. In particular, this can be used to define
    retry rules that apply only to bounce messages. The syntax is to add a new
    third item to a retry rule, of the form "senders=<address list>". The retry
    timings themselves then become the fourth item. For example:

      *   *   senders=:   F,1h,30m

    would match all bounce messages. If the address list contains white space,
    it must be enclosed in quotes. For example:

      a.domain  timeout  senders="x@b.dom : y@c.dom"  G,8h,10m,1.5

    When testing retry rules using -brt, you can supply a sender using the -f
    command line option, like this:

      exim -f "" -brt user@dom.ain

    If you do not set -f with -brt, a retry rule that contains a senders list
    will never be matched.

15. Two new control modifiers have been added to ACLs: "control = enforce_sync"
    and "control = no_enforce_sync". This makes it possible to be selective
    about when SMTP synchronization is enforced. The global option
    smtp_enforce_sync now specifies the default state of the switch. These
    controls can appear in any ACL, but the most obvious place to put them is
    in the ACL defined by acl_smtp_connect, which is run at the start of an
    incoming SMTP connection, before the first synchronization check.

16. Another two new control modifiers are "control = caseful_local_part" and
    "control = caselower_local_part". These are permitted only in the ACL
    specified by acl_smtp_rcpt (i.e. during RCPT processing). By default, the
    contents of $local_part are lower cased before ACL processing.
    After "control = caseful_local_part", any uppercase letters in the original
    local part are restored in $local_part for the rest of the ACL, or until
    "control = caselower_local_part" is encountered. However, this applies only
    to local part handling that takes place directly in the ACL (for example,
    as a key in lookups). If a "verify = recipient" test is obeyed, the
    case-related handling of the local part during the verification is
    controlled by the router configuration (see the caseful_local_part generic
    router option).

    This facility could be used, for example, to add a spam score to local
    parts containing upper case letters. For example, using $acl_m4 to
    accumulate the spam score:

      warn  control = caseful_local_part
            set acl_m4 = ${eval:\
                           $acl_m4 + \
                           ${if match{$local_part}{[A-Z]}{1}{0}}\
                          }
            control = caselower_local_part

    Notice that we put back the lower cased version afterwards, assuming that
    is what is wanted for subsequent tests.

17. The option hosts_connection_nolog is provided so that certain hosts can be
    excepted from logging when the +smtp_connection log selector is set. For
    example, you might want not to log SMTP connections from local processes,
    or from 127.0.0.1, or from your local LAN. The option is a host list with
    an unset default. Because it is consulted in the main loop of the daemon,
    you should strive to restrict its value to a short inline list of IP
    addresses and networks. To disable logging SMTP connections from local
    processes, you must create a host list with an empty item. For example:

      hosts_connection_nolog = :

    If the +smtp_connection log selector is not set, this option has no effect.

18. There is now an acl called acl_smtp_quit, which is run for the QUIT
    command. The outcome of the ACL does not affect the response code to QUIT,
    which is always 221. Thus, the ACL does not in fact control any access.
    For this reason, the only verbs that are permitted are "accept" and "warn".

    The ACL can be used for tasks such as custom logging at the end of an SMTP
    session. For example, you can use ACL variables in other ACLs to count
    messages, recipients, etc., and log the totals at QUIT time using one or
    more "logwrite" modifiers on a "warn" command.

    You do not need to have a final "accept", but if you do, you can use a
    "message" modifier to specify custom text that is sent as part of the 221
    response.

    This ACL is run only for a "normal" QUIT. For certain kinds of disastrous
    failure (for example, failure to open a log file, or when Exim is bombing
    out because it has detected an unrecoverable error), all SMTP commands
    from the client are given temporary error responses until QUIT is received
    or the connection is closed. In these special cases, the ACL is not run.

19. The appendfile transport has two new options, mailbox_size and mailbox_
    filecount. If either these options are set, it is expanded, and the result
    is taken as the current size of the mailbox or the number of files in the
    mailbox, respectively. This makes it possible to use some external means of
    maintaining the data about the size of a mailbox for enforcing quota
    limits. The result of expanding these option values must be a decimal
    number, optionally followed by "K" or "M".

20. It seems that there are broken clients in use that cannot handle multiline
    SMTP responses. Can't people who implement these braindead programs read?
    RFC 821 mentions multiline responses, and it is over 20 years old. They
    must handle multiline responses for EHLO, or do they still use HELO?
    Anyway, here is YAWFAB (yet another workaround for asinine brokenness).
    There's a new ACL switch that can be set by

      control = no_multiline_responses

    If this is set, it suppresses multiline SMTP responses from ACL rejections.
    One way of doing this would have been just to put out these responses as
    one long line. However, RFC 2821 specifies a maximum of 512 bytes per
    response ("use multiline responses for more" it says), and some of the
    responses might get close to that. So I have implemented this by doing two
    very easy things:

      (1) Extra information that is normally output as part of a rejection
          caused by sender verification failure is omitted. Only the final line
          (typically "sender verification failed") is now sent.

      (2) If a "message" modifier supplies a multiline response, only the first
          line is output.

    The setting of the switch can, of course, be made conditional on the
    calling host.

21. There is now support for the libradius library that comes with FreeBSD.
    This is an alternative to the radiusclient library that Exim already
    supports. To use the FreeBSD library, you need to set

      RADIUS_LIB_TYPE=RADLIB

    in Local/Makefile, in addition to RADIUS_CONFIGURE_FILE, and you probably
    also need -libradius in EXTRALIBS.


Version 4.42
------------

 1. The "personal" filter test is brought up-to-date with recommendations from
    the Sieve specification: (a) The list of non-personal From: addresses now
    includes "listserv", "majordomo", and "*-request"; (b) If the message
    contains any header line starting with "List=-" it is treated as
    non-personal.

 2. The Sieve functionality has been extended to support the "copy" and
    "vacation" extensions, and comparison tests.

 3. There is now an overall timeout for performing a callout verification. It
    defaults to 4 times the callout timeout, which applies to individual SMTP
    commands during the callout. The overall timeout applies when there is more
    than one host that can be tried. The timeout is checked before trying the
    next host. This prevents very long delays if there are a large number of
    hosts and all are timing out (e.g. when the network connections are timing
    out). The value of the overall timeout can be changed by specifying an
    additional sub-option for "callout", called "maxwait". For example:

      verify = sender/callout=5s,maxwait=20s

 4. Changes to the "personal" filter test:

    (1) The list of non-personal local parts in From: addresses has been
    extended to include "listserv", "majordomo", "*-request", and "owner-*",
    taken from the Sieve specification recommendations.

    (2) If the message contains any header line starting with "List-" it is
    treated as non-personal.

    (3) The test for "circular" in the Subject: header line has been removed
    because it now seems ill-conceived.

 5. The autoreply transport has a new option called never_mail. This is an
    address list. If any run of the transport creates a message with a
    recipient that matches any item in the list, that recipient is quietly
    discarded. If all recipients are discarded, no message is created.


Version 4.40
------------

The documentation is up-to-date for the 4.40 release. What follows here is a
brief list of the new features that have been added since 4.30.

 1. log_incoming_interface affects more log lines.

 2. New ACL modifier "control = submission".

 3. CONFIGURE_OWNER can be set at build time to define an alternative owner for
    the configuration file, in addition to root and exim.

 4. Added expansion variables $body_zerocount, $recipient_data, and
    $sender_data.

 5. The time of last modification of the "new" subdirectory is now used as the
    "mailbox time last read" when there is a quota error for a maildir
    delivery.

 6. The special item "+ignore_unknown" may now appear in host lists.

 7. The special domain-matching patterns @mx_any, @mx_primary, and
    @mx_secondary can now be followed by "/ignore=<ip list>".

 8. New expansion conditions: match_domain, match_address, match_local_part,
    lt, lti, le, lei, gt, gti, ge, and new expansion operators time_interval,
    eval10, and base62d.

 9. New lookup type called "iplsearch".

10. New log selectors ident_timeout, tls_certificate_verified, queue_time,
    deliver_time, outgoing_port, return_path_on_delivery.

11. New global options smtp_active_hostname and tls_require_ciphers.

12. Exinext has -C and -D options.

13. "domainlist_cache" forces caching of an apparently variable list.

14. For compatibility with Sendmail, the command line option -prval:sval
    is equivalent to -oMr rval -oMs sval.

15. New callout options use_sender and use_postmaster for use when verifying
    recipients.

16. John Jetmore's "exipick" utility has been added to the distribution.

17. The TLS code now supports CRLs.

18. The dnslookup router and the dnsdb lookup type now support the use of SRV
    records.

19. The redirect router has a new option called qualify_domain.

20. exigrep's output now also includes lines that are not related to any
    particular message, but which do match the pattern.

21. New global option write_rejectlog. If it is set false, Exim no longer
    writes anything to the reject log.

****