.cindex CHUNKING "enabling, in client"
.cindex BDAT "SMTP command"
.cindex "RFC 3030" "CHUNKING"
-This option provides a list of server to which, provided they announce
+This option provides a list of servers to which, provided they announce
CHUNKING support, Exim will attempt to use BDAT commands rather than DATA.
BDAT will not be used in conjuction with a transport filter.
.wen
+.new
+.option hosts_try_fastopen smtp "host list!!" unset
+.option "fast open, TCP" "enabling, in client"
+.option "TCP Fast Open" "enabling, in client"
+.option "RFC 7413" "TCP Fast Open"
+This option provides a list of servers to which, provided
+the facility is supported by this system, Exim will attempt to
+perform a TCP Fast Open.
+No data is sent on the SYN segment but, if the remote server also
+supports the facility, it can send its SMTP banner immediately after
+the SYN,ACK segment. This can save up to one round-trip time.
+
+The facility is only active for previously-contacted servers,
+as the initiator must present a cookie in the SYN segment.
+
+On (at least some) current Linux distributions the facility must be enabled
+in the kernel by the sysadmin before the support is usable.
+.wen
+
.option hosts_try_prdr smtp "host list&!!" *
.cindex "PRDR" "enabling, optional in client"
This option provides a list of servers to which, provided they announce
14. If built with EXPERIMENTAL_QUEUEFILE, a queuefile transport, for writing
out copies of the message spool files for use by 3rd-party scanners.
+15. A new option on the smtp transport, hosts_try_fastopen. If the system
+ supports it (on Linux it must be enabled in the kernel by the sysadmin)
+ try to use RFC 7413 "TCP Fast Open". No data is sent on the SYN segment
+ but it permits a peer that also supports the facility to send its SMTP
+ banner immediately after the SYN,ACK segment rather then waiting for
+ another ACK - so saving up to one roundtrip time. Because it requires
+ previous communication with the peer (we save a cookie from it) this
+ will only become active on frequently-contected destinations.
+
Version 4.87
------------
hosts_require_tls host list unset smtp 3.20
hosts_treat_as_local domain list unset main 1.95
hosts_try_auth host list unset smtp 4.00
+hosts_try_fastopen host list unset smtp 4.88
hosts_try_prdr host list unset smtp 4.82 if experimental_prdr
ibase_servers string unset main 4.23
ignore_bounce_errors_after time 0s main 4.00
if (inetd_wait_mode)
{
- int on = 1;
-
listen_socket_count = 1;
listen_sockets = store_get(sizeof(int));
(void) close(3);
if (daemon_listen && !inetd_wait_mode)
{
int sk;
- int on = 1;
ip_address_item *ipa;
/* For each IP address, create a socket, bind it to the appropriate port, and
}
DEBUG(D_any)
- {
if (wildcard)
debug_printf("listening on all interfaces (IPv%c) port %d\n",
- (af == AF_INET6)? '6' : '4', ipa->port);
+ af == AF_INET6 ? '6' : '4', ipa->port);
else
debug_printf("listening on %s port %d\n", ipa->address, ipa->port);
- }
+
+#ifdef TCP_FASTOPEN
+ if (setsockopt(listen_sockets[sk], SOL_TCP, TCP_FASTOPEN, &smtp_connect_backlog,
+ sizeof(smtp_connect_backlog)))
+ log_write(0, LOG_MAIN|LOG_PANIC, "failed to set socket FASTOPEN: %s",
+ strerror(errno));
+#endif
/* Start listening on the bound socket, establishing the maximum backlog of
connections that is allowed. On success, continue to the next address. */
if (!check_special_case(errno, addresses, ipa, TRUE))
log_write(0, LOG_PANIC_DIE, "listen() failed on interface %s: %s",
- wildcard? ((af == AF_INET6)? US"(any IPv6)" : US"(any IPv4)") :
- ipa->address,
+ wildcard
+ ? af == AF_INET6 ? US"(any IPv6)" : US"(any IPv4)" : ipa->address,
strerror(errno));
DEBUG(D_any) debug_printf("wildcard IPv4 listen() failed after IPv6 "
extern void invert_address(uschar *, uschar *);
extern int ip_addr(void *, int, const uschar *, int);
extern int ip_bind(int, int, uschar *, int);
-extern int ip_connect(int, int, const uschar *, int, int);
+extern int ip_connect(int, int, const uschar *, int, int, BOOL);
extern int ip_connectedsocket(int, const uschar *, int, int,
int, host_item *, uschar **);
extern int ip_get_address_family(int);
#endif
BOOL no_multiline_responses = FALSE;
+const int on = 1; /* for setsockopt */
+const int off = 0;
+
uid_t original_euid;
gid_t originator_gid;
uschar *originator_login = NULL;
#endif
extern BOOL no_multiline_responses; /* For broken clients */
+extern const int on; /* For setsockopt */
+extern const int off;
+
extern optionlist optionlist_auths[]; /* These option lists are made */
extern int optionlist_auths_size; /* global so that readconf can */
extern optionlist optionlist_routers[]; /* see them for printing out */
address the remote address, in text form
port the remote port
timeout a timeout (zero for indefinite timeout)
+ fastopen TRUE iff TCP_FASTOPEN can be used
Returns: 0 on success; -1 on failure, with errno set
*/
int
-ip_connect(int sock, int af, const uschar *address, int port, int timeout)
+ip_connect(int sock, int af, const uschar *address, int port, int timeout,
+ BOOL fastopen)
{
struct sockaddr_in s_in4;
struct sockaddr *s_ptr;
callout_address = string_sprintf("[%s]:%d", address, port);
sigalrm_seen = FALSE;
if (timeout > 0) alarm(timeout);
-rc = connect(sock, s_ptr, s_len);
+
+#ifdef TCP_FASTOPEN
+/* TCP Fast Open, if the system has a cookie from a previous call to
+this peer, can send data in the SYN packet. The peer can send data
+before it gets our ACK of its SYN,ACK - the latter is useful for
+the SMTP banner. Is there any usage where the former might be?
+We might extend the ip_connect() args for data if so. For now,
+connect in FASTOPEN mode but with zero data.
+*/
+
+if (fastopen)
+ {
+ if ( (rc = sendto(sock, NULL, 0, MSG_FASTOPEN, s_ptr, s_len)) < 0
+ && errno == EOPNOTSUPP
+ )
+ {
+ log_write(0, LOG_MAIN|LOG_PANIC,
+ "Tried TCP Fast Open but apparently not enabled by sysctl");
+ rc = connect(sock, s_ptr, s_len);
+ }
+ }
+else
+#endif
+ rc = connect(sock, s_ptr, s_len);
+
save_errno = errno;
alarm(0);
/* Try to connect to the server - test each IP till one works */
-for (h = &shost; h != NULL; h = h->next)
+for (h = &shost; h; h = h->next)
{
fd = Ustrchr(h->address, ':') != 0
? fd6 < 0 ? (fd6 = ip_socket(type, af = AF_INET6)) : fd6
}
for(port = portlo; port <= porthi; port++)
- if (ip_connect(fd, af, h->address, port, timeout) == 0)
+ if (ip_connect(fd, af, h->address, port, timeout, type == SOCK_STREAM) == 0)
{
if (fd != fd6) close(fd6);
if (fd != fd4) close(fd4);
listptr = ob->hosts;
while ((hostname = string_nextinlist(&listptr, &sep, host_buffer,
- sizeof(host_buffer))) != NULL)
+ sizeof(host_buffer))))
{
host_item *h;
/* Loop for possible multiple IP addresses for the given name. */
- for (h = host; h != NULL; h = h->next)
+ for (h = host; h; h = h->next)
{
int host_af, query_socket;
/* Skip any hosts for which we have no address */
- if (h->address == NULL) continue;
+ if (!h->address) continue;
/* Create a socket, for UDP or TCP, as configured. IPv6 addresses are
detected by checking for a colon in the address. */
host_af = (Ustrchr(h->address, ':') != NULL)? AF_INET6 : AF_INET;
- query_socket = ip_socket((ob->protocol == ip_udp)? SOCK_DGRAM:SOCK_STREAM,
+
+ query_socket = ip_socket(ob->protocol == ip_udp ? SOCK_DGRAM:SOCK_STREAM,
host_af);
if (query_socket < 0)
{
here only for TCP calls; for a UDP socket, "connect" always works (the
router will timeout later on the read call). */
- if (ip_connect(query_socket, host_af, h->address,ob->port, ob->timeout) < 0)
+ if (ip_connect(query_socket, host_af, h->address,ob->port, ob->timeout,
+ ob->protocol != ip_udp) < 0)
{
close(query_socket);
DEBUG(D_route)
/* If h == NULL we have tried all the IP addresses and failed on all of them,
so we must continue to try more host names. Otherwise we have succeeded. */
- if (h != NULL) break;
+ if (h) break;
}
static BOOL rcpt_smtp_response_same;
static BOOL rcpt_in_progress;
static int nonmail_command_count;
-static int off = 0;
-static int on = 1;
static BOOL smtp_exit_function_called = 0;
#ifdef SUPPORT_I18N
static BOOL smtputf8_advertised;
uschar *iface;
int sep = 0;
-if (istring == NULL) return TRUE;
+if (!istring) return TRUE;
-expint = expand_string(istring);
-if (expint == NULL)
+if (!(expint = expand_string(istring)))
{
if (expand_string_forcedfail) return TRUE;
addr->transport_return = PANIC;
if (*expint == 0) return TRUE;
while ((iface = string_nextinlist(&expint, &sep, big_buffer,
- big_buffer_size)) != NULL)
+ big_buffer_size)))
{
if (string_is_ip_address(iface, NULL) == 0)
{
break;
}
-if (iface != NULL) *interface = string_copy(iface);
+if (iface) *interface = string_copy(iface);
return TRUE;
}
int dscp_level;
int dscp_option;
int sock;
-int on = 1;
int save_errno = 0;
+BOOL fastopen = FALSE;
#ifndef DISABLE_EVENT
deliver_host_address = host->address;
(void) setsockopt(sock, dscp_level, dscp_option, &dscp_value, sizeof(dscp_value));
}
+#ifdef TCP_FASTOPEN
+if (verify_check_given_host (&ob->hosts_try_fastopen, host) == OK) fastopen = TRUE;
+#endif
+
/* Bind to a specific interface if requested. Caller must ensure the interface
is the same type (IPv4 or IPv6) as the outgoing address. */
/* Connect to the remote host, and add keepalive to the socket before returning
it, if requested. */
-else if (ip_connect(sock, host_af, host->address, port, timeout) < 0)
+else if (ip_connect(sock, host_af, host->address, port, timeout, fastopen) < 0)
save_errno = errno;
/* Either bind() or connect() failed */
host.address = US"127.0.0.1";
-for (h = &host; h != NULL; h = h->next)
+for (h = &host; h; h = h->next)
{
int sock, rc;
- int host_af = (Ustrchr(h->address, ':') != NULL)? AF_INET6 : AF_INET;
+ int host_af = Ustrchr(h->address, ':') != NULL ? AF_INET6 : AF_INET;
DEBUG(D_transport) debug_printf("calling comsat on %s\n", h->address);
- sock = ip_socket(SOCK_DGRAM, host_af);
- if (sock < 0) continue;
+ if ((sock = ip_socket(SOCK_DGRAM, host_af)) < 0) continue;
/* Connect never fails for a UDP socket, so don't set a timeout. */
- (void)ip_connect(sock, host_af, h->address, ntohs(sp->s_port), 0);
+ (void)ip_connect(sock, host_af, h->address, ntohs(sp->s_port), 0, FALSE);
rc = send(sock, buffer, Ustrlen(buffer) + 1, 0);
(void)close(sock);
{ "hosts_try_dane", opt_stringptr,
(void *)offsetof(smtp_transport_options_block, hosts_try_dane) },
#endif
+ { "hosts_try_fastopen", opt_stringptr,
+ (void *)offsetof(smtp_transport_options_block, hosts_try_fastopen) },
#ifndef DISABLE_PRDR
{ "hosts_try_prdr", opt_stringptr,
(void *)offsetof(smtp_transport_options_block, hosts_try_prdr) },
NULL, /* hosts_try_dane */
NULL, /* hosts_require_dane */
#endif
+ NULL, /* hosts_try_fastopen */
#ifndef DISABLE_PRDR
US"*", /* hosts_try_prdr */
#endif
static uschar *mail_command; /* Points to MAIL cmd for error messages */
static BOOL update_waiting; /* TRUE to update the "wait" database */
static BOOL pipelining_active; /* current transaction is in pipe mode */
-static int off = 0; /* for use by setsockopt */
/*************************************************
uschar *hosts_try_dane;
uschar *hosts_require_dane;
#endif
+ uschar *hosts_try_fastopen;
#ifndef DISABLE_PRDR
uschar *hosts_try_prdr;
#endif
static uschar cutthrough_response(char, uschar **);
-static int off = 0; /* for use by setsockopt */
/*************************************************
to the incoming interface address. If the sender host address is an IPv6
address, the incoming interface address will also be IPv6. */
-host_af = (Ustrchr(sender_host_address, ':') == NULL)? AF_INET : AF_INET6;
-sock = ip_socket(SOCK_STREAM, host_af);
-if (sock < 0) return;
+host_af = Ustrchr(sender_host_address, ':') == NULL ? AF_INET : AF_INET6;
+if ((sock = ip_socket(SOCK_STREAM, host_af)) < 0) return;
if (ip_bind(sock, host_af, interface_address, 0) < 0)
{
goto END_OFF;
}
-if (ip_connect(sock, host_af, sender_host_address, port, rfc1413_query_timeout)
- < 0)
+if (ip_connect(sock, host_af, sender_host_address, port,
+ rfc1413_query_timeout, TRUE) < 0)
{
if (errno == ETIMEDOUT && LOGGING(ident_timeout))
- {
log_write(0, LOG_MAIN, "ident connection to %s timed out",
sender_host_address);
- }
else
- {
DEBUG(D_ident) debug_printf("ident connection to %s failed: %s\n",
sender_host_address, strerror(errno));
- }
goto END_OFF;
}
--- /dev/null
+# Exim test configuration 2052
+# as per 2000 but with TCP Fast Open
+
+SERVER=
+
+.include DIR/aux-var/tls_conf_prefix
+
+primary_hostname = myhost.test.ex
+
+# ----- Main settings -----
+
+acl_smtp_rcpt = accept
+
+log_selector = +tls_peerdn
+
+queue_only
+queue_run_in_order
+
+tls_advertise_hosts = *
+# needed to force generation
+tls_dhparam = historic
+
+# Set certificate only if server
+
+tls_certificate = ${if eq {SERVER}{server}{DIR/aux-fixed/cert1}fail}
+tls_privatekey = ${if eq {SERVER}{server}{DIR/aux-fixed/cert1}fail}
+
+tls_verify_hosts = *
+tls_verify_certificates = ${if eq {SERVER}{server}{DIR/aux-fixed/cert2}fail}
+
+
+# ----- Routers -----
+
+begin routers
+
+client:
+ driver = accept
+ condition = ${if eq {SERVER}{server}{no}{yes}}
+ retry_use_local_part
+ transport = send_to_server
+
+
+# ----- Transports -----
+
+begin transports
+
+send_to_server:
+ driver = smtp
+ allow_localhost
+ hosts = 127.0.0.1
+ port = PORT_D
+ hosts_try_fastopen = *
+ tls_certificate = DIR/aux-fixed/cert2
+ tls_privatekey = DIR/aux-fixed/cert2
+ tls_verify_certificates = DIR/aux-fixed/cert2
+ tls_try_verify_hosts =
+
+
+# ----- Retry -----
+
+
+begin retry
+
+* * F,5d,10s
+
+
+# End
--- /dev/null
+# Exim test configuration 2152
+# as per 2100 but with TCP Fast Open
+
+SERVER=
+
+.include DIR/aux-var/tls_conf_prefix
+
+primary_hostname = myhost.test.ex
+
+.ifdef _HAVE_TLS
+# that was purely to trigger the lazy-create of builtin macros
+.endif
+# ----- Main settings -----
+
+acl_smtp_rcpt = accept
+
+log_selector = +tls_peerdn
+
+queue_only
+queue_run_in_order
+
+tls_advertise_hosts = *
+
+# Set certificate only if server
+
+tls_certificate = ${if eq {SERVER}{server}{DIR/aux-fixed/cert1}fail}
+tls_privatekey = ${if eq {SERVER}{server}{DIR/aux-fixed/cert1}fail}
+
+tls_verify_hosts = *
+tls_verify_certificates = ${if eq {SERVER}{server}{DIR/aux-fixed/cert2}fail}
+
+
+# ----- Routers -----
+
+begin routers
+
+client:
+ driver = accept
+ condition = ${if eq {SERVER}{server}{no}{yes}}
+ retry_use_local_part
+ transport = send_to_server
+
+
+# ----- Transports -----
+
+begin transports
+
+send_to_server:
+ driver = smtp
+ allow_localhost
+ hosts = 127.0.0.1
+ port = PORT_D
+ hosts_try_fastopen = *
+ tls_certificate = DIR/aux-fixed/cert2
+ tls_privatekey = DIR/aux-fixed/cert2
+ tls_verify_certificates = DIR/aux-fixed/cert2
+ tls_try_verify_hosts = :
+
+
+# ----- Retry -----
+
+
+begin retry
+
+* * F,5d,10s
+
+
+# End
--- /dev/null
+1999-03-02 09:44:33 10HmaX-0005vi-00 <= CALLER@myhost.test.ex U=CALLER P=local S=sss
+1999-03-02 09:44:33 Start queue run: pid=pppp -qf
+1999-03-02 09:44:33 10HmaX-0005vi-00 H=127.0.0.1 [127.0.0.1] TLS error on connection (certificate verification failed): certificate invalid
+1999-03-02 09:44:33 10HmaX-0005vi-00 TLS session failure: delivering unencrypted to 127.0.0.1 [127.0.0.1] (not in hosts_require_tls)
+1999-03-02 09:44:33 10HmaX-0005vi-00 => CALLER@test.ex R=client T=send_to_server H=127.0.0.1 [127.0.0.1] C="250 OK id=10HmaY-0005vi-00"
+1999-03-02 09:44:33 10HmaX-0005vi-00 Completed
+1999-03-02 09:44:33 End queue run: pid=pppp -qf
+
+******** SERVER ********
+1999-03-02 09:44:33 exim x.yz daemon started: pid=pppp, no queue runs, listening for SMTP on port 1225
+1999-03-02 09:44:33 TLS error on connection from localhost [127.0.0.1] (recv): A TLS fatal alert has been received.: Certificate is bad
+1999-03-02 09:44:33 TLS error on connection from localhost [127.0.0.1] (send): The specified session has been invalidated for some reason.
+1999-03-02 09:44:33 10HmaY-0005vi-00 <= CALLER@myhost.test.ex H=localhost (myhost.test.ex) [127.0.0.1] P=esmtp S=sss id=E10HmaX-0005vi-00@myhost.test.ex
--- /dev/null
+1999-03-02 09:44:33 10HmaX-0005vi-00 <= CALLER@myhost.test.ex U=CALLER P=local S=sss
+1999-03-02 09:44:33 Start queue run: pid=pppp -qf
+1999-03-02 09:44:33 10HmaX-0005vi-00 => CALLER@test.ex R=client T=send_to_server H=127.0.0.1 [127.0.0.1] X=TLSv1:AES256-SHA:256 CV=no DN="/C=UK/O=The Exim Maintainers/OU=Test Suite/CN=Phil Pennock" C="250 OK id=10HmaY-0005vi-00"
+1999-03-02 09:44:33 10HmaX-0005vi-00 Completed
+1999-03-02 09:44:33 End queue run: pid=pppp -qf
+
+******** SERVER ********
+1999-03-02 09:44:33 exim x.yz daemon started: pid=pppp, no queue runs, listening for SMTP on port 1225
+1999-03-02 09:44:33 10HmaY-0005vi-00 <= CALLER@myhost.test.ex H=localhost (myhost.test.ex) [127.0.0.1] P=esmtps X=TLSv1:AES256-SHA:256 CV=yes DN="/C=UK/O=The Exim Maintainers/OU=Test Suite/CN=Phil Pennock" S=sss id=E10HmaX-0005vi-00@myhost.test.ex
--- /dev/null
+# TLS client: TLS setup fails - retry in clear (with fastopen)
+#
+# If all works you'll not see any difference. To enable in the
+# kernel, 'sudo sh -c "echo 3 > /proc/sys/net/ipv4/tcp_fastopen"'.
+# A packet capture on the loopback interface will show the TFU
+# option on the SYN, but the fast-output SMTP banner will not
+# be seen unless you also deliberately emulate a long path:
+# 'sudo tc qdisc add dev lo root netem delay 100ms'
+#
+# If the client-side is disabled in the kernel, Exim logs
+# will become noisy.
+#
+gnutls
+exim -DSERVER=server -bd -oX PORT_D
+****
+exim CALLER@test.ex
+Testing
+****
+exim -qf
+****
+killdaemon
+no_msglog_check
--- /dev/null
+# TLS client: TLS setup fails - retry in clear (with fastopen)
+#
+# If all works you'll not see any difference. To enable in the
+# kernel, 'sudo sh -c "echo 3 > /proc/sys/net/ipv4/tcp_fastopen"'.
+# A packet capture on the loopback interface will show the TFU
+# option on the SYN, but the fast-output SMTP banner will not
+# be seen unless you also deliberately emulate a long path:
+# 'sudo tc qdisc add dev lo root netem delay 100ms'
+#
+# If the client-side is disabled in the kernel, Exim logs
+# will become noisy.
+#
+exim -DSERVER=server -bd -oX PORT_D
+****
+exim CALLER@test.ex
+Testing
+****
+exim -qf
+****
+killdaemon
+no_msglog_check
no retry data available
127.0.0.1 in serialize_hosts? no (option unset)
set_process_info: pppp delivering 10HmaX-0005vi-00 to 127.0.0.1 [127.0.0.1] (x@y)
-Connecting to 127.0.0.1 [127.0.0.1]:1224 ... connected
+Connecting to 127.0.0.1 [127.0.0.1]:1224 ... 127.0.0.1 in hosts_try_fastopen? no (option unset)
+connected
SMTP<< 220 Server ready
127.0.0.1 in hosts_avoid_esmtp? no (option unset)
SMTP>> EHLO myhost.test.ex
no retry data available
V4NET.0.0.0 in serialize_hosts? no (option unset)
set_process_info: pppp delivering 10HmaX-0005vi-00 to V4NET.0.0.0 [V4NET.0.0.0] (x@y)
-Connecting to V4NET.0.0.0 [V4NET.0.0.0]:1224 ... failed: Network Error
+Connecting to V4NET.0.0.0 [V4NET.0.0.0]:1224 ... V4NET.0.0.0 in hosts_try_fastopen? no (option unset)
+failed: Network Error
LOG: MAIN
H=V4NET.0.0.0 [V4NET.0.0.0] Network Error
set_process_info: pppp delivering 10HmaX-0005vi-00: just tried V4NET.0.0.0 [V4NET.0.0.0] for x@y: result DEFER
callout cache: no address record found for qq@remote
closed hints database and lockfile
interface=NULL port=1224
-Connecting to 127.0.0.1 [127.0.0.1]:1224 ... connected
+Connecting to 127.0.0.1 [127.0.0.1]:1224 ... 127.0.0.1 in hosts_try_fastopen? no (option unset)
+connected
SMTP<< 220 Server ready
127.0.0.1 in hosts_avoid_esmtp? no (option unset)
SMTP>> EHLO mail.test.ex
callout cache: no address record found for x@y
closed hints database and lockfile
interface=NULL port=1224
-Connecting to 127.0.0.1 [127.0.0.1]:1224 ... connected
+Connecting to 127.0.0.1 [127.0.0.1]:1224 ... 127.0.0.1 in hosts_try_fastopen? no (option unset)
+connected
SMTP<< 220 server ready
127.0.0.1 in hosts_avoid_esmtp? no (option unset)
SMTP>> EHLO myhost.test.ex
>>> callout cache: no domain record found for b
>>> callout cache: no address record found for a@b
>>> interface=NULL port=1224
->>> Connecting to 127.0.0.1 [127.0.0.1]:1224 ... connected
+>>> Connecting to 127.0.0.1 [127.0.0.1]:1224 ... 127.0.0.1 in hosts_try_fastopen? no (option unset)
+>>> connected
>>> SMTP<< 220 server ready
>>> 127.0.0.1 in hosts_avoid_esmtp? no (option unset)
>>> SMTP>> EHLO myhost.test.ex
>>> callout cache: no domain record found for q
>>> callout cache: no address record found for p1@q
>>> interface=NULL port=1224
->>> Connecting to 127.0.0.1 [127.0.0.1]:1224 ... connected
+>>> Connecting to 127.0.0.1 [127.0.0.1]:1224 ... 127.0.0.1 in hosts_try_fastopen? no (option unset)
+>>> connected
>>> SMTP<< 220 server ready
>>> 127.0.0.1 in hosts_avoid_esmtp? no (option unset)
>>> SMTP>> EHLO myhost.test.ex
>>> Attempting full verification using callout
>>> callout cache: disabled by no_cache
>>> interface=ip4.ip4.ip4.ip4 port=1224
->>> Connecting to 127.0.0.1 [127.0.0.1]:1224 from ip4.ip4.ip4.ip4 ... connected
+>>> Connecting to 127.0.0.1 [127.0.0.1]:1224 from ip4.ip4.ip4.ip4 ... 127.0.0.1 in hosts_try_fastopen? no (option unset)
+>>> connected
>>> SMTP<< 220 server ready
>>> 127.0.0.1 in hosts_avoid_esmtp? no (option unset)
>>> SMTP>> EHLO myhost.test.ex
expanding: $local_part
result: userx
domain.com in "*"? yes (matched "*")
-Connecting to 127.0.0.1 [127.0.0.1]:1225 from ip4.ip4.ip4.ip4 ... connected
+Connecting to 127.0.0.1 [127.0.0.1]:1225 from ip4.ip4.ip4.ip4 ... 127.0.0.1 in hosts_try_fastopen? no (option unset)
+connected
considering: $primary_hostname
expanding: $primary_hostname
result: myhost.test.ex
expanding: $local_part
result: usery
domain.com in "*"? yes (matched "*")
-Connecting to 127.0.0.1 [127.0.0.1]:1225 from ip4.ip4.ip4.ip4 ... connected
+Connecting to 127.0.0.1 [127.0.0.1]:1225 from ip4.ip4.ip4.ip4 ... 127.0.0.1 in hosts_try_fastopen? no (option unset)
+connected
considering: $primary_hostname
expanding: $primary_hostname
result: myhost.test.ex
expanding: $local_part
result: usery
domain.com in "*"? yes (matched "*")
-Connecting to 127.0.0.1 [127.0.0.1]:1225 from ip4.ip4.ip4.ip4 ... connected
+Connecting to 127.0.0.1 [127.0.0.1]:1225 from ip4.ip4.ip4.ip4 ... 127.0.0.1 in hosts_try_fastopen? no (option unset)
+connected
considering: $primary_hostname
expanding: $primary_hostname
result: myhost.test.ex
expanding: $local_part
result: userx
domain.com in "*"? yes (matched "*")
-Connecting to 127.0.0.1 [127.0.0.1]:1225 from ip4.ip4.ip4.ip4 ... connected
+Connecting to 127.0.0.1 [127.0.0.1]:1225 from ip4.ip4.ip4.ip4 ... 127.0.0.1 in hosts_try_fastopen? no (option unset)
+connected
considering: $primary_hostname
expanding: $primary_hostname
result: myhost.test.ex
expanding: $local_part
result: usery
domain.com in "*"? yes (matched "*")
-Connecting to 127.0.0.1 [127.0.0.1]:1225 from ip4.ip4.ip4.ip4 ... connected
+Connecting to 127.0.0.1 [127.0.0.1]:1225 from ip4.ip4.ip4.ip4 ... 127.0.0.1 in hosts_try_fastopen? no (option unset)
+connected
considering: $primary_hostname
expanding: $primary_hostname
result: myhost.test.ex
expanding: $local_part
result: usery
domain.com in "*"? yes (matched "*")
-Connecting to 127.0.0.1 [127.0.0.1]:1225 from ip4.ip4.ip4.ip4 ... connected
+Connecting to 127.0.0.1 [127.0.0.1]:1225 from ip4.ip4.ip4.ip4 ... 127.0.0.1 in hosts_try_fastopen? no (option unset)
+connected
considering: $primary_hostname
expanding: $primary_hostname
result: myhost.test.ex
>>> callout cache: no domain record found for dane256ee.test.ex
>>> callout cache: no address record found for CALLER@dane256ee.test.ex
>>> interface=NULL port=1225
->>> Connecting to dane256ee.test.ex [ip4.ip4.ip4.ip4]:1225 ... connected
+>>> Connecting to dane256ee.test.ex [ip4.ip4.ip4.ip4]:1225 ... ip4.ip4.ip4.ip4 in hosts_try_fastopen? no (option unset)
+>>> connected
MUNGED: ::1 will be omitted in what follows
>>> get[host|ipnode]byname[2] looked up these IP addresses:
>>> name=thishost.test.ex address=127.0.0.1
hosts_require_auth =
hosts_try_auth =
hosts_try_chunking = *
+hosts_try_fastopen =
hosts_try_prdr = *
interface = ip4.ip4.ip4.ip4
keepalive
git://git.exim.org / users / heiko / exim.git / commitdiff