Applied latest Sieve patches from the maintainer.

[users/jgh/exim.git] / doc / doc-txt / NewStuff

diff --git a/doc/doc-txt/NewStuff b/doc/doc-txt/NewStuff
index 5936f198b65a556f298f283a6b2c1efdd7c240fd..b6b2d66dab73d91f94c2b9d01422681ccd5d84e8 100644 (file)
--- a/doc/doc-txt/NewStuff
+++ b/doc/doc-txt/NewStuff
@@ -1,4 +1,4 @@
-$Cambridge: exim/doc/doc-txt/NewStuff,v 1.60 2005/08/02 11:22:23 ph10 Exp $
+$Cambridge: exim/doc/doc-txt/NewStuff,v 1.65 2005/08/23 08:50:07 ph10 Exp $

 
 New Features in Exim
 --------------------
 
 New Features in Exim
 --------------------


@@ -42,6 +42,14 @@ PH/01 Support for SQLite database lookups has been added. This is another
       The only character affected by the ${quote_sqlite: operator is a single
       quote, which it doubles.
 
       The only character affected by the ${quote_sqlite: operator is a single
       quote, which it doubles.
 

+      The SQLite library handles multiple simultaneous accesses to the database
+      internally. Multiple readers are permitted, but only one process can
+      update at once. Attempts to access the database while it is being updated
+      are rejected after a timeout period, during which the SQLite library
+      waits for the lock to be released. In Exim, the default timeout is set
+      to 5 seconds, but it can be changed by means of the sqlite_lock_timeout
+      option.
+

       Note that you must set LOOKUP_SQLITE=yes in Local/Makefile in order to
       obtain SQLite support, and you will also need to add -lsqlite3 to the
       EXTRALIBS setting. And of course, you have to install SQLite on your
       Note that you must set LOOKUP_SQLITE=yes in Local/Makefile in order to
       obtain SQLite support, and you will also need to add -lsqlite3 to the
       EXTRALIBS setting. And of course, you have to install SQLite on your


@@ -62,6 +70,44 @@ PH/04 The IGNOREQUOTA extension to the LMTP protocol is now available in both
       provided that the server has advertised support for IGNOREQUOTA in its
       response to the LHLO command.
 
       provided that the server has advertised support for IGNOREQUOTA in its
       response to the LHLO command.
 

+PH/05 Previously, if "verify = helo" was set in an ACL, the condition was true
+      only if the host matched helo_try_verify_hosts, which caused the
+      verification to occur when the EHLO/HELO command was issued. The ACL just
+      tested the remembered result. Now, if a previous verification attempt has
+      not happened, "verify = helo" does it there and then.
+
+PH/06 It is now possible to specify a port number along with a host name or
+      IP address in the list of hosts defined in the manualroute or
+      queryprogram routers, fallback_hosts, or the "hosts" option of the smtp
+      transport. These all override any port specification on the transport.
+      The relatively standard syntax of using a colon separator has been
+      adopted, but there are some gotchas that need attention:
+
+      * In all these lists of hosts, colon is the default separator, so either
+        the colon that specifies a port must be doubled, or the separator must
+        be changed. The following two examples have the same effect:
+
+          fallback_hosts = host1.tld::1225 : host2.tld::1226
+          fallback_hosts = <; host1.tld:1225 ; host2.tld:1226
+
+      * When IPv6 addresses are involved, it gets worse, because they contain
+        colons of their own. To make this case easier, it is permitted to
+        enclose an IP address (either v4 or v6) in square brackets if a port
+        number follows. Here's an example from a manualroute router:
+
+           route_list = * "</ [10.1.1.1]:1225 / [::1]:1226"
+
+      If the "/MX" feature is to be used as well as a port specifier, the port
+      must come last. For example:
+
+           route_list = *  dom1.tld/mx::1225
+
+PH/07 $smtp_command_argument is now set for all SMTP commands, not just the
+      non-message ones. This makes it possible to inspect the complete command
+      for RCPT commands, for example.
+
+PH/08 The ${eval expansion now supports % as a "remainder" operator.
+

 
 Exim version 4.52
 -----------------
 
 Exim version 4.52
 -----------------