-## $Cambridge: exim/doc/doc-src/FAQ.src,v 1.7 2005/05/06 08:28:16 ph10 Exp $
##
## This file is processed by Perl scripts to produce an ASCII and an HTML
## version. Lines starting with ## are omitted. The markup used with paragraphs
==> deny hosts = *.x.example
If at all possible, you should use IP addresses instead of host
- names in blocking lists in order to to avoid this problem.
+ names in blocking lists in order to avoid this problem.
You can use the \-bh-\ option to get more information about what is
happening at the start of a connection. However, note that the \-bh-\
If you are running Exim with an alternate configuration file using a
command such as \"exim -C altconfig..."\, remember that the use of -C
- takes away Exim's root privilege.
+ takes away Exim's root privilege, unless \\TRUSTED_CONFIG_LIST\\
+ is set in \(Local/Makefile)\ and the corresponding file contains a
+ prefix which matches the alternative configuration file being used.
Check that you have defined the spool directory correctly by running
trying to run an \%autoreply%\ transport. Why is this?
A0065: When Exim is called with -C, it passes on -C to any instances of itself
- that it calls (so that the whole sequence uses the same config file). If
- it's running as \/exim/\ when it does this, all is well. However, if it
- happens as a consequence of a non-privileged user running \%autoreply%\,
- the called Exim gives up its root privilege. Then it can't write to the
- spool.
-
- This means that you can't use -C (even as \/root/\) to run an instance of
- Exim that is going to try to run \%autoreply%\ from a process that is
- neither \/root/\ nor \/exim/\. Because of the architecture of Exim (using
- re-execs to regain privilege), there isn't any way round this
- restriction. Therefore, the only way you can make this scenario work is
- to run the \%autoreply%\ transport as \/exim/\ (that is, the user that
- owns the Exim spool files). This may be satisfactory for autoreplies
- that are essentially system-generated, but of course is no good for
- autoreplies from unprivileged users, where you want the \%autoreply%\
- transport to be run as the user. To get that to work with an alternate
- configuration, you'll have to use two Exim binaries, with different
- configuration file names in each. See S001 for a script that patches
- the configuration name in an Exim binary.
+ that it calls (so that the whole sequence uses the same config file).
+ However, Exim gives up its root privilege if any user except \/root\/
+ passes a -C option to use a non-default configuration file, and that
+ includes the case where Exim re-execs itself to regain root privilege.
+ Thus it can't write to the spool.
+
+ The fix for this is to use the \\TRUSTED_CONFIG_LIST\\ build-time
+ option. This defines a file containing a list of 'trusted' prefixes for
+ configuration files. Any configuration file specified with -C, if it
+ matches a prefix listed in that file, will be used without dropping root
+ privileges (as long as it is not writeable by a non-root user).
Q0066: What does the message \*unable to set gid=xxx or uid=xxx*\ mean?
Q0311: When a DNS lookup for MX records fails to complete, why doesn't Exim
- send the messsage to the host defined by the A record?
+ send the message to the host defined by the A record?
A0311: The RFCs are quite clear on this. Only if it is known that there are no
MX records is an MTA allowed to make use of the A record. When an MX
Q0409: I want mail for any local part at certain virtual domains to go
to a single address for each domain.
-A0409: One way to to this is
+A0409: One way to do this is
==> virtual:
driver = redirect
git://git.exim.org / users / jgh / exim.git / blobdiff