&*Warning 2*&: In a host list, you must always use &(net-iplsearch)& so that
the implicit key is the host's IP address rather than its name (see section
&<<SECThoslispatsikey>>&).
+
+.new
+&*Warning 3*&: Do not use an IPv4-mapped IPv6 address for a key; use the
+IPv4. Such addresses being searched for are converted to IPv4.
+.wen
.next
.new
.cindex lookup json
recently implemented &(iplsearch)& files do require colons in IPv6 keys
(notated using the quoting facility) so as to distinguish them from IPv4 keys.
For this reason, when the lookup type is &(iplsearch)&, IPv6 addresses are
-converted using colons and not dots. In all cases, full, unabbreviated IPv6
+converted using colons and not dots.
+.new
+In all cases except IPv4-mapped IPv6, full, unabbreviated IPv6
addresses are always used.
+The latter are converted to IPv4 addresses, in dotted-quad form.
+.wen
Ideally, it would be nice to tidy up this anomalous situation by changing to
colons in all cases, given that quoting is now available for &(lsearch)&.
{<&'string2'&>} must be present for &"fail"& to be recognized.
.vitem "&*${extract json{*&<&'key'&>&*}{*&<&'string1'&>&*}{*&<&'string2'&>&*}&&&
+ {*&<&'string3'&>&*}}*&" &&&
+ "&*${extract jsons{*&<&'key'&>&*}{*&<&'string1'&>&*}{*&<&'string2'&>&*}&&&
{*&<&'string3'&>&*}}*&"
.cindex "expansion" "extracting from JSON object"
.cindex JSON expansions
The braces, commas and colons, and the quoting of the member name are required;
the spaces are optional.
Matching of the key against the member names is done case-sensitively.
-If a returned value is a JSON string, it retains its leading and
+For the &"json"& variant,
+if a returned value is a JSON string, it retains its leading and
trailing quotes.
+.new
+For the &"jsons"& variant, which is intended for use with JSON strings, the
+leading and trailing quotes are removed from the returned value.
+.wen
. XXX should be a UTF-8 compare
The results of matching are handled as above.
empty (for example, the fifth field above).
-.vitem "&*${extract json{*&<&'number'&>&*}}&&&
+.vitem "&*${extract json {*&<&'number'&>&*}}&&&
+ {*&<&'string1'&>&*}{*&<&'string2'&>&*}{*&<&'string3'&>&*}}*&" &&&
+ "&*${extract jsons{*&<&'number'&>&*}}&&&
{*&<&'string1'&>&*}{*&<&'string2'&>&*}{*&<&'string3'&>&*}}*&"
.cindex "expansion" "extracting from JSON array"
.cindex JSON expansions
Field selection and result handling is as above;
there is no choice of field separator.
-If a returned value is a JSON string, it retains its leading and
+For the &"json"& variant,
+if a returned value is a JSON string, it retains its leading and
trailing quotes.
+.new
+For the &"jsons"& variant, which is intended for use with JSON strings, the
+leading and trailing quotes are removed from the returned value.
+.wen
.vitem &*${filter{*&<&'string'&>&*}{*&<&'condition'&>&*}}*&
To scan a named list, expand it with the &*listnamed*& operator.
+.new
+.vitem "&*forall_json{*&<&'a JSON array'&>&*}{*&<&'a condition'&>&*}*&" &&&
+ "&*forany_json{*&<&'a JSON array'&>&*}{*&<&'a condition'&>&*}*&" &&&
+ "&*forall_jsons{*&<&'a JSON array'&>&*}{*&<&'a condition'&>&*}*&" &&&
+ "&*forany_jsons{*&<&'a JSON array'&>&*}{*&<&'a condition'&>&*}*&"
+.cindex JSON "iterative conditions"
+.cindex JSON expansions
+.cindex expansion "&*forall_json*& condition"
+.cindex expansion "&*forany_json*& condition"
+.cindex expansion "&*forall_jsons*& condition"
+.cindex expansion "&*forany_jsons*& condition"
+As for the above, except that the first argument must, after expansion,
+be a JSON array.
+The array separator is not changeable.
+For the &"jsons"& variants the elements are expected to be JSON strings
+and have their quotes removed before the evaluation of the condition.
+.wen
+
+
.vitem &*ge&~{*&<&'string1'&>&*}{*&<&'string2'&>&*}*& &&&
&*gei&~{*&<&'string1'&>&*}{*&<&'string2'&>&*}*&
but in the context of an outward SMTP delivery taking place via the &(smtp)& transport
becomes the same as &$tls_out_cipher$&.
+.new
+.vitem &$tls_in_cipher_std$&
+.vindex "&$tls_in_cipher_std$&"
+As above, but returning the RFC standard name for the cipher suite.
+.wen
+
.vitem &$tls_out_cipher$&
.vindex "&$tls_out_cipher$&"
This variable is
&<<CHAPTLS>>& for details of TLS support and chapter &<<CHAPsmtptrans>>& for
details of the &(smtp)& transport.
+,new
+.vitem &$tls_out_cipher_std$&
+.vindex "&$tls_out_cipher_std$&"
+As above, but returning the RFC standard name for the cipher suite.
+.wen
+
.vitem &$tls_out_dane$&
.vindex &$tls_out_dane$&
DANE active status. See section &<<SECDANE>>&.
used. If the expansion yields an empty string, no &'Received:'& header line is
added to the message. Otherwise, the string should start with the text
&"Received:"& and conform to the RFC 2822 specification for &'Received:'&
-header lines. The default setting is:
+header lines.
+.new
+The default setting is:
.code
received_header_text = Received: \
${if def:sender_rcvhost {from $sender_rcvhost\n\t}\
- {${if def:sender_ident \
- {from ${quote_local_part:$sender_ident} }}\
- ${if def:sender_helo_name {(helo=$sender_helo_name)\n\t}}}}\
+ {${if def:sender_ident \
+ {from ${quote_local_part:$sender_ident} }}\
+ ${if def:sender_helo_name {(helo=$sender_helo_name)\n\t}}}}\
by $primary_hostname \
- ${if def:received_protocol {with $received_protocol}} \
- ${if def:tls_in_cipher {($tls_in_cipher)\n\t}}\
+ ${if def:received_protocol {with $received_protocol }}\
+ ${if def:tls_in_cipher_std { tls $tls_in_cipher_std\n\t}}\
(Exim $version_number)\n\t\
${if def:sender_address \
{(envelope-from <$sender_address>)\n\t}}\
id $message_exim_id\
${if def:received_for {\n\tfor $received_for}}
.endd
+.wen
The reference to the TLS cipher is omitted when Exim is built without TLS
support. The use of conditional expansions ensures that this works for both
rather than being implicit for TLS-connection carried
client certificates only.
-The examples and discussion in this chapter assume that
+The examples and discussion in this chapter assume that
client-certificate authentication is being done.
The client must present a certificate,
&`F `& sender address (on delivery lines)
&`H `& host name and IP address
&`I `& local interface used
-&`id `& message id for incoming message
+&`id `& message id (from header) for incoming message
&`K `& CHUNKING extension used
&`L `& on &`<=`& and &`=>`& lines: PIPELINING extension used
&`M8S `& 8BITMIME status for incoming message
&` incoming_port `& remote port on <= lines
&`*lost_incoming_connection `& as it says (includes timeouts)
&` millisec `& millisecond timestamps and RT,QT,DT,D times
+&`*msg_id `& on <= lines, Message-ID: header value
+&` msg_id_created `& on <= lines, Message-ID: header value when one had to be added
&` outgoing_interface `& local interface on => lines
&` outgoing_port `& add remote port to => lines
&`*queue_run `& start and end queue runs
&%millisec%&: Timestamps have a period and three decimal places of finer granularity
appended to the seconds value.
.next
+.new
+.cindex "log" "message id"
+&%msg_id%&: The value of the Message-ID: header.
+.next
+&%msg_id_created%&: The value of the Message-ID: header, when one had to be created.
+This will be either because the message is a bounce, or was submitted locally
+(submission mode) without one.
+The field identifier will have an asterix appended: &"id*="&.
+.wen
+.next
.cindex "log" "outgoing interface"
.cindex "log" "local interface"
.cindex "log" "local address and port"
.cindex "DKIM" "signing"
For signing to be usable you must have published a DKIM record in DNS.
-Note that RFC 8301 says:
+Note that RFC 8301 (which does not cover EC keys) says:
.code
rsa-sha1 MUST NOT be used for signing or verifying.
.option dkim_domain smtp string list&!! unset
The domain(s) you want to sign with.
After expansion, this can be a list.
-Each element in turn is put into the &%$dkim_domain%& expansion variable
+Each element in turn,
+.new
+lowercased,
+.wen
+is put into the &%$dkim_domain%& expansion variable
while expanding the remaining signing options.
If it is empty after expansion, DKIM signing is not done,
and no error will result even if &%dkim_strict%& is set.
Signers SHOULD use RSA keys of at least 2048 bits.
.endd
-Support for EC keys is being developed under
-&url(https://datatracker.ietf.org/doc/draft-ietf-dcrup-dkim-crypto/).
+.new
+EC keys for DKIM are defined by RFC 8463.
+.wen
They are considerably smaller than RSA keys for equivalent protection.
As they are a recent development, users should consider dual-signing
(by setting a list of selectors, and an expansion for this option)
certtool --load_privkey=dkim_ed25519.private --pubkey_info --outder | tail -c +13 | base64
.endd
-Note that the format
-of Ed25519 keys in DNS has not yet been decided; this release supports
-both of the leading candidates at this time, a future release will
-probably drop support for whichever proposal loses.
+.new
+Exim also supports an alternate format
+of Ed25519 keys in DNS which was a candidate during development
+of the standard, but not adopted.
+A future release will probably drop that support.
+.wen
.option dkim_hash smtp string&!! sha256
Can be set to any one of the supported hash methods, which are:
If a domain or identity is listed several times in the (expanded) value of
&%dkim_verify_signers%&, the ACL is only called once for that domain or identity.
+.new
+Note that if the option is set using untrustworthy data
+(such as the From: header)
+care should be taken to force lowercase for domains
+and for the domain part if identities.
+The default setting can be regarded as trustworthy in this respect.
+.wen
+
If multiple signatures match a domain (or identity), the ACL is called once
for each matching signature.
.endd
If &$proxy_session$& is set but &$proxy_external_address$& is empty
there was a protocol error.
+The variables &$sender_host_address$& and &$sender_host_port$&
+will have values for the actual client system, not the proxy.
Since the real connections are all coming from the proxy, and the
per host connection tracking is done before Proxy Protocol is
git://git.exim.org / users / jgh / exim.git / blobdiff