defined. AAAA records (analogous to A records for IPv4) are in use, and are
currently seen as the mainstream. Another record type called A6 was proposed
as better than AAAA because it had more flexibility. However, it was felt to be
-over-complex, and its status was reduced to &"experimental"&. It is not known
-if anyone is actually using A6 records. Exim has support for A6 records, but
-this is included only if you set &`SUPPORT_A6=YES`& in &_Local/Makefile_&. The
-support has not been tested for some time.
+over-complex, and its status was reduced to &"experimental"&. Exim used to
+have a compile option for including A6 record support but this has now been
+withdrawn.
&<<SECTforexpfai>>& for an explanation of what this means.
The supported DNS record types are A, CNAME, MX, NS, PTR, SPF, SRV, TLSA and TXT,
-and, when Exim is compiled with IPv6 support, AAAA (and A6 if that is also
-configured). If no type is given, TXT is assumed. When the type is PTR,
+and, when Exim is compiled with IPv6 support, AAAA.
+If no type is given, TXT is assumed. When the type is PTR,
the data can be an IP address, written as normal; inversion and the addition of
&%in-addr.arpa%& or &%ip6.arpa%& happens automatically. For example:
.code
If the data for a PTR record is not a syntactically valid IP address, it is not
altered and nothing is added.
-For any record type, if multiple records are found (or, for A6 lookups, if a
-single record leads to multiple addresses), the data is returned as a
+For any record type, if multiple records are found, the data is returned as a
concatenation, with newline as the default separator. The order, of course,
depends on the DNS resolver. You can specify a different separator character
between multiple records by putting a right angle-bracket followed immediately
authorization required but absent, or &"?"& for unknown.
.cindex "A+" "in &(dnsdb)& lookup"
-The pseudo-type A+ performs an A6 lookup (if configured) followed by an AAAA
+The pseudo-type A+ performs an AAAA
and then an A lookup. All results are returned; defer processing
(see below) is handled separately for each lookup. Example:
.code
.row &%acl_smtp_mail%& "ACL for MAIL"
.row &%acl_smtp_mailauth%& "ACL for AUTH on MAIL command"
.row &%acl_smtp_mime%& "ACL for MIME parts"
+.row &%acl_smtp_notquit%& "ACL for non-QUIT terminations"
.row &%acl_smtp_predata%& "ACL for start of data"
.row &%acl_smtp_quit%& "ACL for QUIT"
.row &%acl_smtp_rcpt%& "ACL for RCPT"
extension. It defines the ACL that is run for each MIME part in a message. See
section &<<SECTscanmimepart>>& for details.
+.option acl_smtp_notquit main string&!! unset
+.cindex "not-QUIT, ACL for"
+This option defines the ACL that is run when an SMTP session
+ends without a QUIT command being received.
+See chapter &<<CHAPACL>>& for further details.
+
.option acl_smtp_predata main string&!! unset
This option defines the ACL that is run when an SMTP DATA command is
received, before the message itself is received. See chapter &<<CHAPACL>>& for
an address; if such a router is expected to handle "all remaining non-local
domains", then it is important to set &%no_more%&.
+The router will defer rather than decline if the domain
+is found in the &%fail_defer_domains%& router option.
+
Reasons for a &(dnslookup)& router to decline currently include:
.ilist
The domain does not exist in DNS
.cindex "DNS" "DNSSEC"
DNS lookups for domains matching &%dnssec_request_domains%& will be done with
the dnssec request bit set.
-This applies to all of the SRV, MX A6, AAAA, A lookup sequence.
+This applies to all of the SRV, MX, AAAA, A lookup sequence.
DNS lookups for domains matching &%dnssec_request_domains%& will be done with
the dnssec request bit set. Any returns not having the Authenticated Data bit
(AD bit) set wil be ignored and logged as a host-lookup failure.
-This applies to all of the SRV, MX A6, AAAA, A lookup sequence.
+This applies to all of the SRV, MX, AAAA, A lookup sequence.
+.option fail_defer_domains dnslookup "domain list&!!" unset
+.cindex "MX record" "not found"
+DNS lookups for domains matching &%fail_defer_domains%&
+which find no matching record will cause the router to defer
+rather than the default behaviour of decline.
+This maybe be useful for queueing messages for a newly created
+domain while the DNS configuration is not ready.
+However, it will result in any message with mistyped domains
+also being queued.
+
+
.option mx_domains dnslookup "domain list&!!" unset
.cindex "MX record" "required to exist"
.cindex "SRV record" "required to exist"
.cindex "DNS" "DNSSEC"
DNS lookups for domains matching &%dnssec_request_domains%& will be done with
the dnssec request bit set.
-This applies to all of the SRV, MX A6, AAAA, A lookup sequence.
+This applies to all of the SRV, MX, AAAA, A lookup sequence.
DNS lookups for domains matching &%dnssec_request_domains%& will be done with
the dnssec request bit set. Any returns not having the Authenticated Data bit
(AD bit) set wil be ignored and logged as a host-lookup failure.
-This applies to all of the SRV, MX A6, AAAA, A lookup sequence.
+This applies to all of the SRV, MX, AAAA, A lookup sequence.
legitimate reasons for this (host died, network died), but if it repeats a lot
for the same host, it indicates something odd.
+.vitem &%lookup%&
+A DNS lookup for a host failed.
+Note that a &%dnslookup%& router will need to have matched
+its &%fail_defer_domains%& option for this retry type to be usable.
+Also note that a &%manualroute%& router will probably need
+its &%host_find_failed%& option set to &%defer%&.
+
.vitem &%refused_MX%&
A connection to a host obtained from an MX record was refused.
.cindex "QUIT, ACL for"
The ACL for the SMTP QUIT command is anomalous, in that the outcome of the ACL
does not affect the response code to QUIT, which is always 221. Thus, the ACL
-does not in fact control any access. For this reason, the only verbs that are
-permitted are &%accept%& and &%warn%&.
+does not in fact control any access. For this reason, it may only accept
+or warn as its final result.
This ACL can be used for tasks such as custom logging at the end of an SMTP
session. For example, you can use ACL variables in other ACLs to count
git://git.exim.org / users / jgh / exim.git / blobdiff