-This file contains descriptions of new features that have been added to Exim,
-but have not yet made it into the main manual (which is most conveniently
-updated when there is a relatively large batch of changes). The doc/ChangeLog
-file contains a listing of all changes, including bug fixes.
-
-
-Exim version 4.52
------------------
-
-TF/01 Support for checking Client SMTP Authorization has been added. CSA is a
- system which allows a site to advertise which machines are and are not
- permitted to send email. This is done by placing special SRV records in
- the DNS, which are looked up using the client's HELO domain. At this
- time CSA is still an Internet-Draft.
-
- Client SMTP Authorization checks are performed by the ACL condition
- verify=csa. This will fail if the client is not authorized. If there is
- a DNS problem, or if no valid CSA SRV record is found, or if the client
- is authorized, the condition succeeds. These three cases can be
- distinguished using the expansion variable $csa_status, which can take
- one of the values "fail", "defer", "unknown", or "ok". The condition
- does not itself defer because that would be likely to cause problems
- for legitimate email.
-
- The error messages produced by the CSA code include slightly more
- detail. If $csa_status is "defer" this may be because of problems
- looking up the CSA SRV record, or problems looking up the CSA target
- address record. There are four reasons for $csa_status being "fail":
- the client's host name is explicitly not authorized; the client's IP
- address does not match any of the CSA target IP addresses; the client's
- host name is authorized but it has no valid target IP addresses (e.g.
- the target's addresses are IPv6 and the client is using IPv4); or the
- client's host name has no CSA SRV record but a parent domain has
- asserted that all subdomains must be explicitly authorized.
-
- The verify=csa condition can take an argument which is the domain to
- use for the DNS query. The default is verify=csa/$sender_helo_name.
-
- This implementation includes an extension to CSA. If the query domain
- is an address literal such as [192.0.2.95], or if it is a bare IP
- address, Exim will search for CSA SRV records in the reverse DNS as if
- the HELO domain was e.g. 95.2.0.192.in-addr.arpa. Therefore it is
- meaningful to say, for example, verify=csa/$sender_host_address - in
- fact, this is the check that Exim performs if the client does not say
- HELO. This extension can be turned off by setting the main
- configuration option dns_csa_use_reverse = false.
-
- If a CSA SRV record is not found for the domain itself, then a search
- is performed through its parent domains for a record which might be
- making assertions about subdomains. The maximum depth of this search is
- limited using the main configuration option dns_csa_search_limit, which
- takes the value 5 by default. Exim does not look for CSA SRV records in
- a top level domain, so the default settings handle HELO domains as long
- as seven (hostname.five.four.three.two.one.com) which encompasses the
- vast majority of legitimate HELO domains.
-
- The dnsdb lookup also has support for CSA. Although dnsdb already
- supports SRV lookups, this is not sufficient because of the extra
- parent domain search behaviour of CSA, and (as with PTR lookups)
- dnsdb also turns IP addresses into lookups in the reverse DNS space.
- The result of ${lookup dnsdb {csa=$sender_helo_name} } has two
- space-separated fields: an authorization code and a target host name.
- The authorization code can be "Y" for yes, "N" for no, "X" for explicit
- authorization required but absent, or "?" for unknown.
-
-PH/01 The amount of output produced by the "make" process has been reduced,
- because the compile lines are often rather long, making it all pretty
- unreadable. The new style is along the lines of the 2.6 Linux kernel:
- just a short line for each module that is being compiled or linked.
- However, it is still possible to get the full output, by calling "make"
- like this:
-
- FULLECHO='' make -e
-
- The value of FULLECHO defaults to "@", the flag character that suppresses
- command reflection in "make". When you ask for the full output, it is
- given in addition to the the short output.
-
-
-Version 4.51
+This file contains descriptions of new features that have been added to Exim.
+Before a formal release, there may be quite a lot of detail so that people can
+test from the snapshots or the CVS before the documentation is updated. Once
+the documentation is updated, this file is reduced to a short list.
+
+
+Version 4.64
+------------
+
+ 1. ACL variables can now be given arbitrary names, as long as they start with
+ "acl_c" or "acl_m" (for connection variables and message variables), are at
+ least six characters long, with the sixth character being either a digit or
+ an underscore.
+
+ 2. There is a new ACL modifier called log_reject_target. It makes it possible
+ to specify which logs are used for messages about ACL rejections.
+
+ 3. There is a new authenticator called "dovecot". This is an interface to the
+ authentication facility of the Dovecot POP/IMAP server, which can support a
+ number of authentication methods.
+
+ 4. The variable $message_headers_raw provides a concatenation of all the
+ messages's headers without any decoding. This is in contrast to
+ $message_headers, which does RFC2047 decoding on the header contents.
+
+ 5. In a DNS black list, if two domain names, comma-separated, are given, the
+ second is used first to do an initial check, making use of any IP value
+ restrictions that are set. If there is a match, the first domain is used,
+ without any IP value restrictions, to get the TXT record.
+
+ 6. All authenticators now have a server_condition option.
+
+ 7. There is a new command-line option called -Mset. It is useful only in
+ conjunction with -be (that is, when testing string expansions). It must be
+ followed by a message id; Exim loads the given message from its spool
+ before doing the expansions.
+
+ 8. Another similar new command-line option is called -bem. It operates like
+ -be except that it must be followed by the name of a file that contains a
+ message.
+
+ 9. When an address is delayed because of a 4xx response to a RCPT command, it
+ is now the combination of sender and recipient that is delayed in
+ subsequent queue runs until its retry time is reached.
+
+10. Unary negation and the bitwise logical operators and, or, xor, not, and
+ shift, have been added to the eval: and eval10: expansion items.
+
+11. The variables $interface_address and $interface_port have been renamed
+ as $received_ip_address and $received_port, to make it clear that they
+ relate to message reception rather than delivery. (The old names remain
+ available for compatibility.)
+
+12. The "message" modifier can now be used on "accept" and "discard" acl verbs
+ to vary the message that is sent when an SMTP command is accepted.
+
+
+Version 4.63
git://git.exim.org / users / jgh / exim.git / blobdiff