&`process_info `& setting info for the process log
&`queue_run `& queue runs
&`receive `& general message reception logic
&`process_info `& setting info for the process log
&`queue_run `& queue runs
&`receive `& general message reception logic
&`retry `& retry handling
&`rewrite `& address rewriting
&`route `& address routing
&`retry `& retry handling
&`rewrite `& address rewriting
&`route `& address routing
+.new
+.cindex debugging "UTF-8 in"
+.cindex UTF-8 "in debug output"
+The &`noutf8`& selector disables the use of
+UTF-8 line-drawing characters to group related information.
+When disabled. ascii-art is used instead.
+Using the &`+all`& option does not set this modifier,
+.wen
+
If the &%debug_print%& option is set in any driver, it produces output whenever
any debugging is selected, or if &%-v%& is used.
If the &%debug_print%& option is set in any driver, it produces output whenever
any debugging is selected, or if &%-v%& is used.
.vitem &*$rheader_*&<&'header&~name'&>&*:*&&~or&~&*$rh_*&<&'header&~name'&>&*:*&
This item inserts &"raw"& header lines. It is described with the &%header%&
.vitem &*$rheader_*&<&'header&~name'&>&*:*&&~or&~&*$rh_*&<&'header&~name'&>&*:*&
This item inserts &"raw"& header lines. It is described with the &%header%&
the value of &$authenticated_id$& is normally the login name of the calling
process. However, a trusted user can override this by means of the &%-oMai%&
command line option.
the value of &$authenticated_id$& is normally the login name of the calling
process. However, a trusted user can override this by means of the &%-oMai%&
command line option.
inserting the message header line with the given name. Note that the name must
be terminated by colon or white space, because it may contain a wide variety of
characters. Note also that braces must &'not'& be used.
inserting the message header line with the given name. Note that the name must
be terminated by colon or white space, because it may contain a wide variety of
characters. Note also that braces must &'not'& be used.
A list of hosts, whether obtained via &%route_data%& or &%route_list%&, is
always separately expanded before use. If the expansion fails, the router
declines. The result of the expansion must be a colon-separated list of names
A list of hosts, whether obtained via &%route_data%& or &%route_list%&, is
always separately expanded before use. If the expansion fails, the router
declines. The result of the expansion must be a colon-separated list of names
-and/or IP addresses, optionally also including ports. The format of each item
+and/or IP addresses, optionally also including ports.
+If the list is written with spaces, it must be protected with quotes.
+The format of each item
in the list is described in the next section. The list separator can be changed
as described in section &<<SECTlistconstruct>>&.
in the list is described in the next section. The list separator can be changed
as described in section &<<SECTlistconstruct>>&.
This option controls what happens when all remote IP addresses for a given
domain have been inaccessible for so long that they have passed their retry
cutoff times.
This option controls what happens when all remote IP addresses for a given
domain have been inaccessible for so long that they have passed their retry
cutoff times.
If the value of this option begins with a digit it is taken as a port number;
otherwise it is looked up using &[getservbyname()]&. The default value is
If the value of this option begins with a digit it is taken as a port number;
otherwise it is looked up using &[getservbyname()]&. The default value is
-normally &"smtp"&, but if &%protocol%& is set to &"lmtp"&, the default is
-&"lmtp"&. If the expansion fails, or if a port number cannot be found, delivery
+normally &"smtp"&,
+but if &%protocol%& is set to &"lmtp"& the default is &"lmtp"&
+and if &%protocol%& is set to &"smtps"& the default is &"smtps"&.
+If the expansion fails, or if a port number cannot be found, delivery
If this option is set to &"smtps"&, the default value for the &%port%& option
changes to &"smtps"&, and the transport initiates TLS immediately after
connecting, as an outbound SSL-on-connect, instead of using STARTTLS to upgrade.
If this option is set to &"smtps"&, the default value for the &%port%& option
changes to &"smtps"&, and the transport initiates TLS immediately after
connecting, as an outbound SSL-on-connect, instead of using STARTTLS to upgrade.
-The Internet standards bodies strongly discourage use of this mode.
+.new
+The Internet standards bodies used to strongly discourage use of this mode,
+but as of RFC 8314 it is perferred over STARTTLS for message submission
+(as distinct from MTA-MTA communication).
+.wen
messages. If this delivery fails, the address fails immediately. The
post-cutoff retry time is not used.
messages. If this delivery fails, the address fails immediately. The
post-cutoff retry time is not used.
If the delivery is remote, there are two possibilities, controlled by the
.oindex "&%delay_after_cutoff%&"
&%delay_after_cutoff%& option of the &(smtp)& transport. The option is true by
If the delivery is remote, there are two possibilities, controlled by the
.oindex "&%delay_after_cutoff%&"
&%delay_after_cutoff%& option of the &(smtp)& transport. The option is true by
reached, the failing email address is bounced immediately, without a delivery
attempt taking place. After that time, one new delivery attempt is made to
those IP addresses that are past their retry times, and if that still fails,
reached, the failing email address is bounced immediately, without a delivery
attempt taking place. After that time, one new delivery attempt is made to
those IP addresses that are past their retry times, and if that still fails,
When an Exim server successfully authenticates a client, this string is
expanded using data from the authentication, and preserved for any incoming
messages in the variable &$authenticated_id$&. It is also included in the log
lines for incoming messages. For example, a user/password authenticator
configuration might preserve the user name that was used to authenticate, and
refer to it subsequently during delivery of the message.
When an Exim server successfully authenticates a client, this string is
expanded using data from the authentication, and preserved for any incoming
messages in the variable &$authenticated_id$&. It is also included in the log
lines for incoming messages. For example, a user/password authenticator
configuration might preserve the user name that was used to authenticate, and
refer to it subsequently during delivery of the message.
&%pipelining%&: A field is added to delivery and accept
log lines when the ESMTP PIPELINING extension was used.
The field is a single "L".
&%pipelining%&: A field is added to delivery and accept
log lines when the ESMTP PIPELINING extension was used.
The field is a single "L".
On accept lines, where PIPELINING was offered but not used by the client,
the field has a minus appended.
.next
On accept lines, where PIPELINING was offered but not used by the client,
the field has a minus appended.
.next