-2. Use the following global settings to configure DMARC:
-
-Required:
-dmarc_tld_file Defines the location of a text file of valid
- top level domains the opendmarc library uses
- during domain parsing. Maintained by Mozilla,
- the most current version can be downloaded
- from a link at http://publicsuffix.org/list/.
-
-Optional:
-dmarc_history_file Defines the location of a file to log results
- of dmarc verification on inbound emails. The
- contents are importable by the opendmarc tools
- which will manage the data, send out DMARC
- reports, and expire the data. Make sure the
- directory of this file is writable by the user
- exim runs as.
-
-dmarc_forensic_sender The email address to use when sending a
- forensic report detailing alignment failures
- if a sender domain's dmarc record specifies it
- and you have configured Exim to send them.
- Default: do-not-reply@$default_hostname
-
-
-3. By default, the DMARC processing will run for any remote,
-non-authenticated user. It makes sense to only verify DMARC
-status of messages coming from remote, untrusted sources. You can
-use standard conditions such as hosts, senders, etc, to decide that
-DMARC verification should *not* be performed for them and disable
-DMARC with a control setting:
-
- control = dmarc_verify_disable
-
-A DMARC record can also specify a "forensic address", which gives
-exim an email address to submit reports about failed alignment.
-Exim does not do this by default because in certain conditions it
-results in unintended information leakage (what lists a user might
-be subscribed to, etc). You must configure exim to submit forensic
-reports to the owner of the domain. If the DMARC record contains a
-forensic address and you specify the control statement below, then
-exim will send these forensic emails. It's also advised that you
-configure a dmarc_forensic_sender because the default sender address
-construction might be inadequate.
-
- control = dmarc_forensic_enable
-
-(AGAIN: You can choose not to send these forensic reports by simply
-not putting the dmarc_forensic_enable control line at any point in
-your exim config. If you don't tell it to send them, it will not
-send them.)
-
-There are no options to either control. Both must appear before
-the DATA acl.
-
-
-4. You can now run DMARC checks in incoming SMTP by using the
-"dmarc_status" ACL condition in the DATA ACL. You are required to
-call the spf condition first in the ACLs, then the "dmarc_status"
-condition. Putting this condition in the ACLs is required in order
-for a DMARC check to actually occur. All of the variables are set
-up before the DATA ACL, but there is no actual DMARC check that
-occurs until a "dmarc_status" condition is encountered in the ACLs.
-
-The dmarc_status condition takes a list of strings on its
-right-hand side. These strings describe recommended action based
-on the DMARC check. To understand what the policy recommendations
-mean, refer to the DMARC website above. Valid strings are:
-
- o accept The DMARC check passed and the library recommends
- accepting the email.
- o reject The DMARC check failed and the library recommends
- rejecting the email.
- o quarantine The DMARC check failed and the library recommends
- keeping it for further inspection.
- o norecord No policy section in the DMARC record for this
- sender domain.
- o nofrom Unable to determine the domain of the sender.
- o none There is no DMARC record for this sender domain.
- o error Library error or dns error.
-
-You can prefix each string with an exclamation mark to invert its
-meaning, for example "!accept" will match all results but
-"accept". The string list is evaluated left-to-right in a
-short-circuit fashion. When a string matches the outcome of the
-DMARC check, the condition succeeds. If none of the listed
-strings matches the outcome of the DMARC check, the condition
-fails.
-
-Of course, you can also use any other lookup method that Exim
-supports, including LDAP, Postgres, MySQL, etc, as long as the
-result is a list of colon-separated strings;
-
-Several expansion variables are set before the DATA ACL is
-processed, and you can use them in this ACL. The following
-expansion variables are available:
-
- o $dmarc_status
- This is a one word status indicating what the DMARC library
- thinks of the email.
-
- o $dmarc_status_text
- This is a slightly longer, human readable status.
-
- o $dmarc_used_domain
- This is the domain which DMARC used to look up the DMARC
- policy record.
-
- o $dmarc_ar_header
- This is the entire Authentication-Results header which you can
- add using an add_header modifier.
-
-
-5. How to enable DMARC advanced operation:
-By default, Exim's DMARC configuration is intended to be
-non-intrusive and conservative. To facilitate this, Exim will not
-create any type of logging files without explicit configuration by
-you, the admin. Nor will Exim send out any emails/reports about
-DMARC issues without explicit configuration by you, the admin (other
-than typical bounce messages that may come about due to ACL
-processing or failure delivery issues).
-
-In order to log statistics suitable to be imported by the opendmarc
-tools, you need to:
-a. Configure the global setting dmarc_history_file.
-b. Configure cron jobs to call the appropriate opendmarc history
- import scripts and truncating the dmarc_history_file.
-
-In order to send forensic reports, you need to:
-a. Configure the global setting dmarc_forensic_sender.
-b. Configure, somewhere before the DATA ACL, the control option to
- enable sending DMARC forensic reports.
-
-
-6. Example usage:
-(RCPT ACL)
- warn domains = +local_domains
- hosts = +local_hosts
- control = dmarc_verify_disable
-
- warn !domains = +screwed_up_dmarc_records
- control = dmarc_enable_forensic
-
-(DATA ACL)
- warn dmarc_status = accept : none : off
- !authenticated = *
- log_message = DMARC DEBUG: $dmarc_status $dmarc_used_domain
- add_header = $dmarc_ar_header
-
- warn dmarc_status = !accept
- !authenticated = *
- log_message = DMARC DEBUG: '$dmarc_status' for $dmarc_used_domain
-
- warn dmarc_status = quarantine
- !authenticated = *
- set $acl_m_quarantine = 1
- # Do something in a transport with this flag variable
-
- deny dmarc_status = reject
- !authenticated = *
- message = Message from $domain_used_domain failed sender's DMARC policy, REJECT
git://git.exim.org / users / jgh / exim.git / blobdiff