. Update the Copyright year (only) when changing content.
. /////////////////////////////////////////////////////////////////////////////
-.set previousversion "4.91"
+.set previousversion "4.93"
.include ./local_params
.set ACL "access control lists (ACLs)"
.set I " "
.macro copyyear
-2018
+2019
.endmacro
. /////////////////////////////////////////////////////////////////////////////
of domains that it defines.
.next
.vindex "&$local_part_prefix$&"
+.vindex "&$local_part_prefix_v$&"
.vindex "&$local_part$&"
.vindex "&$local_part_suffix$&"
+.vindex "&$local_part_suffix_v$&"
.cindex affix "router precondition"
If the &%local_parts%& option is set, the local part of the address must be in
the set of local parts that it defines. If &%local_part_prefix%& or
&%local_part_suffix%& is in use, the prefix or suffix is removed from the local
part before this check. If you want to do precondition tests on local parts
that include affixes, you can do so by using a &%condition%& option (see below)
-that uses the variables &$local_part$&, &$local_part_prefix$&, and
-&$local_part_suffix$& as necessary.
+.new
+that uses the variables &$local_part$&, &$local_part_prefix$&,
+&$local_part_prefix_v$&, &$local_part_suffix$&
+and &$local_part_suffix_v$& as necessary.
+.wen
.next
.vindex "&$local_user_uid$&"
.vindex "&$local_user_gid$&"
.section "Including TLS/SSL encryption support" "SECTinctlsssl"
.cindex "TLS" "including support for TLS"
.cindex "encryption" "including support for"
-.cindex "SUPPORT_TLS"
.cindex "OpenSSL" "building Exim with"
.cindex "GnuTLS" "building Exim with"
-Exim can be built to support encrypted SMTP connections, using the STARTTLS
-command as per RFC 2487. It can also support legacy clients that expect to
+Exim is usually built to support encrypted SMTP connections, using the STARTTLS
+command as per RFC 2487. It can also support clients that expect to
start a TLS session immediately on connection to a non-standard port (see the
&%tls_on_connect_ports%& runtime option and the &%-tls-on-connect%& command
line option).
OpenSSL or GnuTLS library. There is no cryptographic code in Exim itself for
implementing SSL.
+If you do not want TLS support you should set
+.code
+DISABLE_TLS=yes
+.endd
+in &_Local/Makefile_&.
+
If OpenSSL is installed, you should set
.code
-SUPPORT_TLS=yes
+USE_OPENSL=yes
TLS_LIBS=-lssl -lcrypto
.endd
in &_Local/Makefile_&. You may also need to specify the locations of the
OpenSSL library and include files. For example:
.code
-SUPPORT_TLS=yes
+USE_OPENSSL=yes
TLS_LIBS=-L/usr/local/openssl/lib -lssl -lcrypto
TLS_INCLUDE=-I/usr/local/openssl/include/
.endd
.cindex "pkg-config" "OpenSSL"
If you have &'pkg-config'& available, then instead you can just use:
.code
-SUPPORT_TLS=yes
+USE_OPENSSL=yes
USE_OPENSSL_PC=openssl
.endd
.cindex "USE_GNUTLS"
If GnuTLS is installed, you should set
.code
-SUPPORT_TLS=yes
USE_GNUTLS=yes
TLS_LIBS=-lgnutls -ltasn1 -lgcrypt
.endd
in &_Local/Makefile_&, and again you may need to specify the locations of the
library and include files. For example:
.code
-SUPPORT_TLS=yes
USE_GNUTLS=yes
TLS_LIBS=-L/usr/gnu/lib -lgnutls -ltasn1 -lgcrypt
TLS_INCLUDE=-I/usr/gnu/include
.cindex "pkg-config" "GnuTLS"
If you have &'pkg-config'& available, then instead you can just use:
.code
-SUPPORT_TLS=yes
USE_GNUTLS=yes
USE_GNUTLS_PC=gnutls
.endd
If you are already running Exim on your host, building and installing a new
version automatically makes it available to MUAs, or any other programs that
call the MTA directly. However, if you are running an Exim daemon, you do need
+.cindex restart "on HUP signal"
+.cindex signal "HUP, to restart"
to send it a HUP signal, to make it re-execute itself, and thereby pick up the
new binary. You do not need to stop processing mail in order to install a new
version of Exim. The install script does not modify an existing runtime
configuration option. Note that the Exim group is not automatically trusted.
.cindex '&"From"& line'
+.cindex "envelope from"
.cindex "envelope sender"
Trusted users are always permitted to use the &%-f%& option or a leading
&"From&~"& line to specify the envelope sender of a message that is passed to
The SIGHUP signal
.cindex "SIGHUP"
+.cindex restart "on HUP signal"
+.cindex signal "HUP, to restart"
.cindex "daemon" "restarting"
+.cindex signal "to reload configuration"
+.cindex daemon "reload configuration"
+.cindex reload configuration
can be used to cause the daemon to re-execute itself. This should be done
whenever Exim's configuration file, or any file that is incorporated into it by
means of the &%.include%& facility, is changed, and also whenever a new version
When testing a filter file,
.cindex "&""From""& line"
+.cindex "envelope from"
.cindex "envelope sender"
.oindex "&%-f%&" "for filter testing"
the envelope sender can be set by the &%-f%& option,
of all debug output lines. This can be useful when trying to track down delays
in processing.
-.new
.cindex debugging "UTF-8 in"
.cindex UTF-8 "in debug output"
The &`noutf8`& selector disables the use of
UTF-8 line-drawing characters to group related information.
When disabled. ascii-art is used instead.
Using the &`+all`& option does not set this modifier,
-.wen
If the &%debug_print%& option is set in any driver, it produces output whenever
any debugging is selected, or if &%-v%& is used.
.cindex "sender" "address"
.cindex "address" "sender"
.cindex "trusted users"
+.cindex "envelope from"
.cindex "envelope sender"
.cindex "user" "trusted"
This option sets the address of the envelope sender of a locally-generated
Bounce messages are just discarded. This option can be used only by an admin
user.
+.vitem &%-MG%&&~<&'queue&~name'&>&~<&'message&~id'&>&~<&'message&~id'&>&~...
+.oindex "&%-MG%&"
+.cindex queue named
+.cindex "named queues" "moving messages"
+.cindex "queue" "moving messages"
+This option requests that each listed message be moved from its current
+queue to the given named queue.
+The destination queue name argument is required, but can be an empty
+string to define the default queue.
+If the messages are not currently located in the default queue,
+a &%-qG<name>%& option will be required to define the source queue.
+
.vitem &%-Mmad%&&~<&'message&~id'&>&~<&'message&~id'&>&~...
.oindex "&%-Mmad%&"
.cindex "delivery" "cancelling all"
.vitem &%-odqs%&
.oindex "&%-odqs%&"
.cindex "SMTP" "delaying delivery"
+.cindex "first pass routing"
This option is a hybrid between &%-odb%&/&%-odi%& and &%-odq%&.
However, like &%-odb%& and &%-odi%&, this option has no effect if
&%queue_only_override%& is false and one of the queueing options in the
without &%-bd%&, this is the only way of causing Exim to write a pid file,
because in those cases, the normal pid file is not used.
+.new
+.vitem &%-oPX%&
+.oindex "&%-oPX%&"
+.cindex "pid (process id)" "of daemon"
+.cindex "daemon" "process id (pid)"
+This option is not intended for general use.
+The daemon uses it when terminating due to a SIGTEM, possibly in
+combination with &%-oP%&&~<&'path'&>.
+It causes the pid file to be removed.
+.wen
+
.vitem &%-or%&&~<&'time'&>
.oindex "&%-or%&"
.cindex "timeout" "for non-SMTP input"
.cindex "queue" "double scanning"
.cindex "queue" "routing"
.cindex "routing" "whole queue before delivery"
+.cindex "first pass routing"
An option starting with &%-qq%& requests a two-stage queue run. In the first
stage, the queue is scanned as if the &%queue_smtp_domains%& option matched
every domain. Addresses are routed, local deliveries happen, but no remote
transports are run.
+.new
+Performance will be best if the &%queue_run_in_order%& option is false.
+.wen
+
.cindex "hints database" "remembering routing"
The hints database that remembers which messages are waiting for specific hosts
is updated, as if delivery to those hosts had been deferred. After this is
.vitem &%-q[q][i][f[f]][l][G<name>[/<time>]]]%&
.oindex "&%-qG%&"
.cindex queue named
-.cindex "named queues"
+.cindex "named queues" "deliver from"
.cindex "queue" "delivering specific messages"
If the &'G'& flag and a name is present, the queue runner operates on the
queue with the given name rather than the default queue.
remote_smtp:
driver = smtp
message_size_limit = ${if > {$max_received_linelength}{998} {1}{0}}
-.ifdef _HAVE_DANE
- dnssec_request_domains = *
- hosts_try_dane = *
+.ifdef _HAVE_PRDR
+ hosts_try_prdr = *
.endif
.endd
This transport is used for delivering messages over SMTP connections.
The list of remote hosts comes from the router.
The &%message_size_limit%& usage is a hack to avoid sending on messages
-with over-long lines. The built-in macro _HAVE_DANE guards configuration
-to try to use DNSSEC for all queries and to use DANE for delivery;
-see section &<<SECDANE>>& for more details.
+with over-long lines.
+
+The &%hosts_try_prdr%& option enables an efficiency SMTP option. It is
+negotiated between client and server and not expected to cause problems
+but can be disabled if needed. The built-in macro _HAVE_PRDR guards the
+use of the &%hosts_try_prdr%& configuration option.
The other remote transport is used when delivering to a specific smarthost
with whom there must be some kind of existing relationship, instead of the
tls_require_ciphers = SECURE192:-VERS-SSL3.0:-VERS-TLS1.0:-VERS-TLS1.1
.endif
.endif
+.ifdef _HAVE_PRDR
+ hosts_try_prdr = *
+.endif
.endd
After the same &%message_size_limit%& hack, we then specify that this Transport
can handle messages to multiple domains in one run. The assumption here is
You want to specify the hostname which you'll expect to validate for, and that
should not be subject to insecure tampering via DNS results.
+For the &%hosts_try_prdr%& option see the previous transport.
+
+All other options are defaulted.
.code
local_delivery:
driver = appendfile
- file = /var/mail/$local_part
+ file = /var/mail/$local_part_verified
delivery_date_add
envelope_to_add
return_path_add
# mode = 0660
.endd
This &(appendfile)& transport is used for local delivery to user mailboxes in
-traditional BSD mailbox format. By default it runs under the uid and gid of the
+traditional BSD mailbox format.
+
+.new
+We prefer to avoid using &$local_part$& directly to define the mailbox filename,
+as it is provided by a potential bad actor.
+Instead we use &$local_part_verified$&,
+the result of looking up &$local_part$& in the user database
+(done by using &%check_local_user%& in the the router).
+.wen
+
+By default &(appendfile)& runs under the uid and gid of the
local user, which requires the sticky bit to be set on the &_/var/mail_&
directory. Some systems use the alternative approach of running mail deliveries
under a particular group instead of using the sticky bit. The commented options
tools for building the files can be found in several places:
.display
&url(https://cr.yp.to/cdb.html)
-&url(http://www.corpit.ru/mjt/tinycdb.html)
+&url(https://www.corpit.ru/mjt/tinycdb.html)
&url(https://packages.debian.org/stable/utils/freecdb)
&url(https://github.com/philpennock/cdbtools) (in Go)
.endd
-. --- 2018-09-07: corpit.ru http:-only
A cdb distribution is not needed in order to build Exim with cdb support,
because the code for reading cdb files is included directly in Exim itself.
However, no means of building or testing cdb files is provided with Exim, so
&*Warning 2*&: In a host list, you must always use &(net-iplsearch)& so that
the implicit key is the host's IP address rather than its name (see section
&<<SECThoslispatsikey>>&).
+
+&*Warning 3*&: Do not use an IPv4-mapped IPv6 address for a key; use the
+IPv4, in dotted-quad form. (Exim converts IPv4-mapped IPv6 addresses to this
+notation before executing the lookup.)
+.next
+.cindex lookup json
+.cindex json "lookup type"
+.cindex JSON expansions
+&(json)&: The given file is a text file with a JSON structure.
+An element of the structure is extracted, defined by the search key.
+The key is a list of subelement selectors
+(colon-separated by default but changeable in the usual way)
+which are applied in turn to select smaller and smaller portions
+of the JSON structure.
+If a selector is numeric, it must apply to a JSON array; the (zero-based)
+nunbered array element is selected.
+Otherwise it must apply to a JSON object; the named element is selected.
+The final resulting element can be a simple JSON type or a JSON object
+or array; for the latter two a string-representation os the JSON
+is returned.
+For elements of type string, the returned value is de-quoted.
.next
.cindex "linear search"
.cindex "lookup" "lsearch"
With &"strict"& a response from the DNS resolver that
is not labelled as authenticated data
is treated as equivalent to a temporary DNS error.
-The default is &"never"&.
+The default is &"lax"&.
See also the &$lookup_dnssec_authenticated$& variable.
where &'x.y'& does not match. It's best to avoid negation altogether in
referenced lists if you can.
+.new
+.cindex "hiding named list values"
+.cindex "named lists" "hiding value of"
+Some named list definitions may contain sensitive data, for example, passwords for
+accessing databases. To stop non-admin users from using the &%-bP%& command
+line option to read these values, you can precede the definition with the
+word &"hide"&. For example:
+.code
+hide domainlist filter_for_domains = ldap;PASS=secret ldap::/// ...
+.endd
+.wen
+
+
Named lists may have a performance advantage. When Exim is routing an
address or checking an incoming message, it caches the result of tests on named
lists. So, if you have a setting such as
recently implemented &(iplsearch)& files do require colons in IPv6 keys
(notated using the quoting facility) so as to distinguish them from IPv4 keys.
For this reason, when the lookup type is &(iplsearch)&, IPv6 addresses are
-converted using colons and not dots. In all cases, full, unabbreviated IPv6
+converted using colons and not dots.
+In all cases except IPv4-mapped IPv6, full, unabbreviated IPv6
addresses are always used.
+The latter are converted to IPv4 addresses, in dotted-quad form.
Ideally, it would be nice to tidy up this anomalous situation by changing to
colons in all cases, given that quoting is now available for &(lsearch)&.
them are expanded every time they are used; others are expanded only once.
When a string is being expanded it is copied verbatim from left to right except
+.cindex expansion "string concatenation"
when a dollar or backslash character is encountered. A dollar specifies the
start of a portion of the string that is interpreted and replaced as described
below in section &<<SECTexpansionitems>>& onwards. Backslash is used as an
options for which string expansion is performed are marked with † after
the data type. ACL rules always expand strings. A couple of expansion
conditions do not expand some of the brace-delimited branches, for security
-reasons.
+reasons,
+.cindex "tainted data" expansion
+.cindex expansion "tainted data"
+and expansion of data deriving from the sender (&"tainted data"&)
+is not permitted.
.cindex headers "authentication-results:"
.cindex authentication "expansion item"
This item returns a string suitable for insertion as an
-&'Authentication-Results"'&
+&'Authentication-Results:'&
header line.
The given <&'authserv-id'&> is included in the result; typically this
will be a domain name identifying the system performing the authentications.
object so that it doesn't reload the same object file in the same Exim process
(but of course Exim does start new processes frequently).
-There may be from zero to eight arguments to the function. When compiling
-a local function that is to be called in this way, &_local_scan.h_& should be
-included. The Exim variables and functions that are defined by that API
+There may be from zero to eight arguments to the function.
+
+When compiling
+a local function that is to be called in this way,
+first &_DLFUNC_IMPL_& should be defined,
+and second &_local_scan.h_& should be included.
+The Exim variables and functions that are defined by that API
are also available for dynamically loaded functions. The function itself
must have the following type:
.code
This forces an expansion failure (see section &<<SECTforexpfai>>&);
{<&'string2'&>} must be present for &"fail"& to be recognized.
-.new
.vitem "&*${extract json{*&<&'key'&>&*}{*&<&'string1'&>&*}{*&<&'string2'&>&*}&&&
+ {*&<&'string3'&>&*}}*&" &&&
+ "&*${extract jsons{*&<&'key'&>&*}{*&<&'string1'&>&*}{*&<&'string2'&>&*}&&&
{*&<&'string3'&>&*}}*&"
.cindex "expansion" "extracting from JSON object"
.cindex JSON expansions
The braces, commas and colons, and the quoting of the member name are required;
the spaces are optional.
Matching of the key against the member names is done case-sensitively.
+For the &"json"& variant,
+if a returned value is a JSON string, it retains its leading and
+trailing quotes.
+For the &"jsons"& variant, which is intended for use with JSON strings, the
+leading and trailing quotes are removed from the returned value.
. XXX should be a UTF-8 compare
The results of matching are handled as above.
-.wen
.vitem "&*${extract{*&<&'number'&>&*}{*&<&'separators'&>&*}&&&
empty (for example, the fifth field above).
-.new
-.vitem "&*${extract json{*&<&'number'&>&*}}&&&
+.vitem "&*${extract json {*&<&'number'&>&*}}&&&
+ {*&<&'string1'&>&*}{*&<&'string2'&>&*}{*&<&'string3'&>&*}}*&" &&&
+ "&*${extract jsons{*&<&'number'&>&*}}&&&
{*&<&'string1'&>&*}{*&<&'string2'&>&*}{*&<&'string3'&>&*}}*&"
.cindex "expansion" "extracting from JSON array"
.cindex JSON expansions
Field selection and result handling is as above;
there is no choice of field separator.
-.wen
+For the &"json"& variant,
+if a returned value is a JSON string, it retains its leading and
+trailing quotes.
+For the &"jsons"& variant, which is intended for use with JSON strings, the
+leading and trailing quotes are removed from the returned value.
.vitem &*${filter{*&<&'string'&>&*}{*&<&'condition'&>&*}}*&
.cindex "expansion" "selecting from list by condition"
.vindex "&$item$&"
After expansion, <&'string'&> is interpreted as a list, colon-separated by
-default, but the separator can be changed in the usual way. For each item
+default, but the separator can be changed in the usual way (&<<SECTlistsepchange>>&).
+For each item
in this list, its value is place in &$item$&, and then the condition is
evaluated. If the condition is true, &$item$& is added to the output as an
item in a new list; if the condition is false, the item is discarded. The
${filter{a:b:c}{!eq{$item}{b}}}
.endd
yields &`a:c`&. At the end of the expansion, the value of &$item$& is restored
-to what it was before. See also the &*map*& and &*reduce*& expansion items.
+to what it was before. See also the &%map%& and &%reduce%& expansion items.
.vitem &*${hash{*&<&'string1'&>&*}{*&<&'string2'&>&*}{*&<&'string3'&>&*}}*&
"&*$bheader_*&<&'header&~name'&>&*:*&&~or&~&&&
&*$bh_*&<&'header&~name'&>&*:*&" &&&
"&*$lheader_*&<&'header&~name'&>&*:*&&~or&~&&&
- &*$lh_*&<&'header&~name'&>&*:*&"
+ &*$lh_*&<&'header&~name'&>&*:*&" &&&
"&*$rheader_*&<&'header&~name'&>&*:*&&~or&~&&&
&*$rh_*&<&'header&~name'&>&*:*&"
.cindex "expansion" "header insertion"
those headers that contain lists of addresses, a comma is also inserted at the
junctions between headers. This does not happen for the &%rheader%& expansion.
+.new
+.cindex "tainted data"
+When the headers are from an incoming message,
+the result of expanding any of these variables is tainted.
+.wen
+
.vitem &*${hmac{*&<&'hashname'&>&*}{*&<&'secret'&>&*}{*&<&'string'&>&*}}*&
.cindex "expansion" "hmac hashing"
and leading and trailing white space (which is ignored).
After expansion, <&'string1'&> is interpreted as a list, colon-separated by
-default, but the separator can be changed in the usual way.
+default, but the separator can be changed in the usual way (&<<SECTlistsepchange>>&).
The first field of the list is numbered one.
If the number is negative, the fields are
.cindex "expansion" "list creation"
.vindex "&$item$&"
After expansion, <&'string1'&> is interpreted as a list, colon-separated by
-default, but the separator can be changed in the usual way. For each item
+default, but the separator can be changed in the usual way (&<<SECTlistsepchange>>&).
+For each item
in this list, its value is place in &$item$&, and then <&'string2'&> is
expanded and added to the output as an item in a new list. The separator used
for the output list is the same as the one used for the input, but a separator
${map{a:b:c}{[$item]}} ${map{<- x-y-z}{($item)}}
.endd
expands to &`[a]:[b]:[c] (x)-(y)-(z)`&. At the end of the expansion, the
-value of &$item$& is restored to what it was before. See also the &*filter*&
-and &*reduce*& expansion items.
+value of &$item$& is restored to what it was before. See also the &%filter%&
+and &%reduce%& expansion items.
.vitem &*${nhash{*&<&'string1'&>&*}{*&<&'string2'&>&*}{*&<&'string3'&>&*}}*&
.cindex "expansion" "numeric hash"
.code
${readsocket{/socket/name}{request string}{3s:shutdown=no}}
.endd
-.new
The second, tls, controls the use of TLS on the connection. Example:
.code
${readsocket{/socket/name}{request string}{3s:tls=yes}}
.endd
The default is to not use TLS.
If it is enabled, a shutdown as descripbed above is never done.
-.wen
A fourth argument allows you to change any newlines that are in the data
that is read, in the same way as for &%readfile%& (see above). This example
.vindex "&$item$&"
This operation reduces a list to a single, scalar string. After expansion,
<&'string1'&> is interpreted as a list, colon-separated by default, but the
-separator can be changed in the usual way. Then <&'string2'&> is expanded and
+separator can be changed in the usual way (&<<SECTlistsepchange>>&).
+Then <&'string2'&> is expanded and
assigned to the &$value$& variable. After this, each item in the <&'string1'&>
list is assigned to &$item$&, in turn, and <&'string3'&> is expanded for each of
them. The result of that expansion is assigned to &$value$& before the next
iteration. When the end of the list is reached, the final value of &$value$& is
-added to the expansion output. The &*reduce*& expansion item can be used in a
+added to the expansion output. The &%reduce%& expansion item can be used in a
number of ways. For example, to add up a list of numbers:
.code
${reduce {<, 1,2,3}{0}{${eval:$value+$item}}}
${reduce {3:0:9:4:6}{0}{${if >{$item}{$value}{$item}{$value}}}}
.endd
At the end of a &*reduce*& expansion, the values of &$item$& and &$value$& are
-restored to what they were before. See also the &*filter*& and &*map*&
+restored to what they were before. See also the &%filter%& and &%map%&
expansion items.
.vitem &*$rheader_*&<&'header&~name'&>&*:*&&~or&~&*$rh_*&<&'header&~name'&>&*:*&
.cindex list sorting
.cindex expansion "list sorting"
After expansion, <&'string'&> is interpreted as a list, colon-separated by
-default, but the separator can be changed in the usual way.
+default, but the separator can be changed in the usual way (&<<SECTlistsepchange>>&).
The <&'comparator'&> argument is interpreted as the operator
of a two-argument expansion condition.
The numeric operators plus ge, gt, le, lt (and ~i variants) are supported.
${addresses:>:$h_from:}
.endd
-Compare the &*address*& (singular)
+Compare the &%address%& (singular)
expansion item, which extracts the working address from a single RFC2822
-address. See the &*filter*&, &*map*&, and &*reduce*& items for ways of
+address. See the &%filter%&, &%map%&, and &%reduce%& items for ways of
processing lists.
To clarify "list of addresses in RFC 2822 format" mentioned above, Exim follows
returns the SHA-1 hash fingerprint of the certificate.
-.vitem &*${sha256:*&<&'string'&>&*}*&
+.vitem &*${sha256:*&<&'string'&>&*}*& &&&
+ &*${sha2:*&<&'string'&>&*}*& &&&
+ &*${sha2_<n>:*&<&'string'&>&*}*&
.cindex "SHA-256 hash"
+.cindex "SHA-2 hash"
.cindex certificate fingerprint
.cindex "expansion" "SHA-256 hashing"
.cindex "&%sha256%& expansion item"
+.cindex "&%sha2%& expansion item"
The &%sha256%& operator computes the SHA-256 hash value of the string
and returns
it as a 64-digit hexadecimal number, in which any letters are in upper case.
If the string is a single variable of type certificate,
returns the SHA-256 hash fingerprint of the certificate.
+The operator can also be spelled &%sha2%& and does the same as &%sha256%&
+(except for certificates, which are not supported).
+Finally, if an underbar
+and a number is appended it specifies the output length, selecting a
+member of the SHA-2 family of hash functions.
+Values of 256, 384 and 512 are accepted, with 256 being the default.
+
.vitem &*${sha3:*&<&'string'&>&*}*& &&&
&*${sha3_<n>:*&<&'string'&>&*}*&
.cindex "expansion" "utf-8 forcing"
.cindex "&%utf8clean%& expansion item"
This replaces any invalid utf-8 sequence in the string by the character &`?`&.
-.new
In versions of Exim before 4.92, this did not correctly do so for a truncated
final codepoint's encoding, and the character would be silently dropped.
If you must handle detection of this scenario across both sets of Exim behavior,
.endd
(which will false-positive if the first character of the local part is a
literal question mark).
-.wen
.vitem "&*${utf8_domain_to_alabel:*&<&'string'&>&*}*&" &&&
"&*${utf8_domain_from_alabel:*&<&'string'&>&*}*&" &&&
.vindex "&$item$&"
These conditions iterate over a list. The first argument is expanded to form
the list. By default, the list separator is a colon, but it can be changed by
-the normal method. The second argument is interpreted as a condition that is to
+the normal method (&<<SECTlistsepchange>>&).
+The second argument is interpreted as a condition that is to
be applied to each item in the list in turn. During the interpretation of the
condition, the current list item is placed in a variable called &$item$&.
.ilist
.code
${if forany{<, $recipients}{match{$item}{^user3@}}{yes}{no}}
.endd
-The value of &$item$& is saved and restored while &*forany*& or &*forall*& is
+The value of &$item$& is saved and restored while &%forany%& or &%forall%& is
being processed, to enable these expansion items to be nested.
To scan a named list, expand it with the &*listnamed*& operator.
+.vitem "&*forall_json{*&<&'a JSON array'&>&*}{*&<&'a condition'&>&*}*&" &&&
+ "&*forany_json{*&<&'a JSON array'&>&*}{*&<&'a condition'&>&*}*&" &&&
+ "&*forall_jsons{*&<&'a JSON array'&>&*}{*&<&'a condition'&>&*}*&" &&&
+ "&*forany_jsons{*&<&'a JSON array'&>&*}{*&<&'a condition'&>&*}*&"
+.cindex JSON "iterative conditions"
+.cindex JSON expansions
+.cindex expansion "&*forall_json*& condition"
+.cindex expansion "&*forany_json*& condition"
+.cindex expansion "&*forall_jsons*& condition"
+.cindex expansion "&*forany_jsons*& condition"
+As for the above, except that the first argument must, after expansion,
+be a JSON array.
+The array separator is not changeable.
+For the &"jsons"& variants the elements are expected to be JSON strings
+and have their quotes removed before the evaluation of the condition.
+
+
.vitem &*ge&~{*&<&'string1'&>&*}{*&<&'string2'&>&*}*& &&&
&*gei&~{*&<&'string1'&>&*}{*&<&'string2'&>&*}*&
.vindex "&$config_file$&"
The name of the main configuration file Exim is using.
+.vitem &$dmarc_domain_policy$& &&&
+ &$dmarc_status$& &&&
+ &$dmarc_status_text$& &&&
+ &$dmarc_used_domains$&
+Results of DMARC verification.
+For details see section &<<SECDMARC>>&.
+
.vitem &$dkim_verify_status$&
Results of DKIM verification.
For details see section &<<SECDKIMVFY>>&.
the complete argument of the ETRN command (see section &<<SECTETRN>>&).
.endlist
+.new
+.cindex "tainted data"
+If the origin of the data is an incoming message,
+the result of expanding this variable is tainted.
+See also &$domain_verified$&.
+.wen
+
.vitem &$domain_data$&
.vindex "&$domain_data$&"
The first character is a major version number, currently 4.
Then after a dot, the next group of digits is a minor version number.
There may be other characters following the minor version.
+This value may be overridden by the &%exim_version%& main config option.
.vitem &$header_$&<&'name'&>
This is not strictly an expansion variable. It is expansion syntax for
.cindex authentication "expansion item"
Performing these checks sets up information used by the
-&$authresults$& expansion item.
+&%authresults%& expansion item.
.vitem &$host_lookup_failed$&
because a message may have many recipients and the system filter is called just
once.
+.new
+.cindex "tainted data"
+If the origin of the data is an incoming message,
+the result of expanding this variable is tainted.
+
+&*Warning*&: the content of this variable is usually provided by a potential
+attacker.
+Consider carefully the implications of using it unvalidated as a name
+for file access.
+This presents issues for users' &_.forward_& and filter files.
+For traditional full user accounts, use &%check_local_users%& and the
+&$local_part_verified$& variable rather than this one.
+For virtual users, store a suitable pathname component in the database
+which is used for account name validation, and use that retrieved value
+rather than this variable.
+If needed, use a router &%address_data%& or &%set%& option for
+the retrieved data.
+.wen
+
.vindex "&$local_part_prefix$&"
+.vindex "&$local_part_prefix_v$&"
.vindex "&$local_part_suffix$&"
+.vindex "&$local_part_suffix_v$&"
.cindex affix variables
If a local part prefix or suffix has been recognized, it is not included in the
value of &$local_part$& during routing and subsequent delivery. The values of
any prefix or suffix are in &$local_part_prefix$& and
&$local_part_suffix$&, respectively.
+.new
+If the affix specification included a wildcard then the portion of
+the affix matched by the wildcard is in
+&$local_part_prefix_v$& or &$local_part_suffix_v$& as appropriate.
+.wen
When a message is being delivered to a file, pipe, or autoreply transport as a
result of aliasing or forwarding, &$local_part$& is set to the local part of
specific prefix for the local part was recognized, it is available in this
variable, having been removed from &$local_part$&.
+.new
+.vitem &$local_part_prefix_v$&
+.vindex "&$local_part_prefix_v$&"
+When &$local_part_prefix$& is valid and the prefix match used a wildcard,
+the portion matching the wildcard is available in this variable.
+.wen
+
.vitem &$local_part_suffix$&
.vindex "&$local_part_suffix$&"
When an address is being routed or delivered, and a
specific suffix for the local part was recognized, it is available in this
variable, having been removed from &$local_part$&.
+.new
+.vitem &$local_part_suffix_v$&
+.vindex "&$local_part_suffix_v$&"
+When &$local_part_suffix$& is valid and the suffix match used a wildcard,
+the portion matching the wildcard is available in this variable.
+.wen
+
+.new
+.vitem &$local_part_verified$&
+.vindex "&$local_part_verified$&"
+If the router generic option &%check_local_part%& has run successfully,
+this variable has the user database version of &$local_part$&.
+Such values are not tainted and hence usable for building file names.
+.wen
+
.vitem &$local_scan_data$&
.vindex "&$local_scan_data$&"
This variable contains the text returned by the &[local_scan()]& function when
.vitem &$queue_name$&
.vindex &$queue_name$&
-.cindex "named queues"
+.cindex "named queues" variable
.cindex queues named
The name of the spool queue in use; empty for the default queue.
+.vitem &$queue_size$&
+.vindex "&$queue_size$&"
+.cindex "queue" "size of"
+.cindex "spool" "number of messages"
+This variable contains the number of messages queued.
+It is evaluated on demand, but no more often than once every minute.
+
+.vitem &$r_...$&
+.vindex &$r_...$&
+.cindex router variables
+Values can be placed in these variables by the &%set%& option of a router.
+They can be given any name that starts with &$r_$&.
+The values persist for the address being handled through subsequent routers
+and the eventual transport.
+
.vitem &$rcpt_count$&
.vindex "&$rcpt_count$&"
When a message is being received by SMTP, this variable contains the number of
&*Note*&: Under versions of OpenSSL preceding 1.1.1,
when a list of more than one
file is used for &%tls_certificate%&, this variable is not reliable.
+The macro "_TLS_BAD_MULTICERT_IN_OURCERT" will be defined for those versions.
.vitem &$tls_in_peercert$&
.vindex "&$tls_in_peercert$&"
but in the context of an outward SMTP delivery taking place via the &(smtp)& transport
becomes the same as &$tls_out_cipher$&.
+.vitem &$tls_in_cipher_std$&
+.vindex "&$tls_in_cipher_std$&"
+As above, but returning the RFC standard name for the cipher suite.
+
.vitem &$tls_out_cipher$&
.vindex "&$tls_out_cipher$&"
This variable is
&<<CHAPTLS>>& for details of TLS support and chapter &<<CHAPsmtptrans>>& for
details of the &(smtp)& transport.
+.vitem &$tls_out_cipher_std$&
+.vindex "&$tls_out_cipher_std$&"
+As above, but returning the RFC standard name for the cipher suite.
+
.vitem &$tls_out_dane$&
.vindex &$tls_out_dane$&
DANE active status. See section &<<SECDANE>>&.
.vindex &$tls_out_tlsa_usage$&
Bitfield of TLSA record types found. See section &<<SECDANE>>&.
+.vitem &$tls_in_ver$&
+.vindex "&$tls_in_ver$&"
+When a message is received from a remote host over an encrypted SMTP connection
+this variable is set to the protocol version, eg &'TLS1.2'&.
+
+.vitem &$tls_out_ver$&
+.vindex "&$tls_out_ver$&"
+When a message is being delivered to a remote host over an encrypted SMTP connection
+this variable is set to the protocol version.
+
+
.vitem &$tod_bsdinbox$&
.vindex "&$tod_bsdinbox$&"
The time of day and the date, in the format required for BSD-style mailbox
.vitem &$version_number$&
.vindex "&$version_number$&"
-The version number of Exim.
+The version number of Exim. Same as &$exim_version$&, may be overridden
+by the &%exim_version%& main config option.
.vitem &$warn_message_delay$&
.vindex "&$warn_message_delay$&"
.endlist
The default list separator in both cases is a colon, but this can be changed as
-described in section &<<SECTlistconstruct>>&. When IPv6 addresses are involved,
+described in section &<<SECTlistsepchange>>&. When IPv6 addresses are involved,
it is usually best to change the separator to avoid having to double all the
colons. For example:
.code
exim.
The value of &%-oX%& is a list of items. The default colon separator can be
-changed in the usual way if required. If there are any items that do not
+changed in the usual way (&<<SECTlistsepchange>>&) if required.
+If there are any items that do not
contain dots or colons (that is, are not IP addresses), the value of
&%daemon_smtp_ports%& is replaced by the list of those items. If there are any
items that do contain dots or colons, the value of &%local_interfaces%& is
See also the &'Policy controls'& section above.
.table2
-.row &%dkim_verify_signers%& "DKIM domain for which DKIM ACL is run"
+.row &%dkim_verify_hashes%& "DKIM hash methods accepted for signatures"
+.row &%dkim_verify_keytypes%& "DKIM key types accepted for signatures"
+.row &%dkim_verify_signers%& "DKIM domains for which DKIM ACL is run"
.row &%host_lookup%& "host name looked up for these hosts"
.row &%host_lookup_order%& "order of DNS and local name lookups"
.row &%recipient_unqualified_hosts%& "may send unqualified recipients"
.row &%ignore_fromline_hosts%& "allow &""From ""& from these hosts"
.row &%ignore_fromline_local%& "allow &""From ""& from local SMTP"
.row &%pipelining_advertise_hosts%& "advertise pipelining to these hosts"
+.row &%pipelining_connect_advertise_hosts%& "advertise pipelining to these hosts"
.row &%prdr_enable%& "advertise PRDR to all hosts"
.row &%smtputf8_advertise_hosts%& "advertise SMTPUTF8 to these hosts"
.row &%tls_advertise_hosts%& "advertise TLS to these hosts"
.option add_environment main "string list" empty
.cindex "environment" "set values"
-This option allows to set individual environment variables that the
-currently linked libraries and programs in child processes use.
+This option adds individual environment variables that the
+currently linked libraries and programs in child processes may use.
+Each list element should be of the form &"name=value"&.
+
See &<<SECTpipeenv>>& for the environment of &(pipe)& transports.
.option admin_groups main "string list&!!" unset
.cindex "UTF-8" "in domain name"
Lots of discussion is going on about internationalized domain names. One
camp is strongly in favour of just using UTF-8 characters, and it seems
-that at least two other MTAs permit this. This option allows Exim users to
-experiment if they wish.
+that at least two other MTAs permit this.
+This option allows Exim users to experiment if they wish.
If it is set true, Exim's domain parsing function allows valid
UTF-8 multicharacters to appear in domain name components, in addition to
-letters, digits, and hyphens. However, just setting this option is not
-enough; if you want to look up these domain names in the DNS, you must also
+letters, digits, and hyphens.
+
+If Exim is built with internationalization support
+and the SMTPUTF8 ESMTP option is in use (see chapter &<<CHAPi18n>>&)
+this option can be left as default.
+Without that,
+if you want to look up such domain names in the DNS, you must also
adjust the value of &%dns_check_names_pattern%& to match the extended form. A
suitable setting is:
.code
to handle IPv6 literal addresses.
+.new
+.option dkim_verify_hashes main "string list" "sha256 : sha512"
+.cindex DKIM "selecting signature algorithms"
+This option gives a list of hash types which are acceptable in signatures,
+.wen
+and an order of processing.
+Signatures with algorithms not in the list will be ignored.
+
+Acceptable values include:
+.code
+sha1
+sha256
+sha512
+.endd
+
+Note that the acceptance of sha1 violates RFC 8301.
+
+.option dkim_verify_keytypes main "string list" "ed25519 : rsa"
+This option gives a list of key types which are acceptable in signatures,
+and an order of processing.
+Signatures with algorithms not in the list will be ignored.
+
+.option dkim_verify_minimal main boolean false
+If set to true, verification of signatures will terminate after the
+first success.
+
.option dkim_verify_signers main "domain list&!!" $dkim_signers
.cindex DKIM "controlling calls to the ACL"
This option gives a list of DKIM domains for which the DKIM ACL is run.
reversed and looked up in the reverse DNS, as described in more detail in
section &<<SECTverifyCSA>>&.
-.new
.option dns_cname_loops main integer 1
.cindex DNS "CNAME following"
This option controls the following of CNAME chains, needed if the resolver does
The default value of one CNAME-follow is needed
thanks to the observed return for an MX request,
given no MX presence but a CNAME to an A, of the CNAME.
-.wen
.option dns_dnssec_ok main integer -1
This is a fudge to help with name servers that give big delays or otherwise do
not work for the AAAA record type. In due course, when the world's name
servers have all been upgraded, there should be no need for this option.
+Note that all lookups, including those done for verification, are affected;
+this will result in verify failure for IPv6 connections or ones using names
+only valid for IPv6 addresses.
.option dns_retrans main time 0s
used. See chapter &<<CHAPsecurity>>& for a discussion of security issues.
+.option exim_version main string "current version"
+.cindex "Exim version"
+.cindex customizing "version number"
+.cindex "version number of Exim" override
+This option overrides the &$version_number$&/&$exim_version$& that Exim reports in
+various places. Use with care; this may fool stupid security scanners.
+
+
.option extra_local_interfaces main "string list" unset
This option defines network interfaces that are to be considered local when
routing, but which are not used for listening by the daemon. See section
&'Sender:'& header lines supplied by untrusted users, you must also set
&%local_sender_retain%& to be true.
+.cindex "envelope from"
.cindex "envelope sender"
These options affect only the header lines in the message. The envelope sender
is still forced to be the login id at the qualify domain unless
name. If no specific path is set for the log files at compile or runtime,
or if the option is unset at runtime (i.e. &`log_file_path = `&)
they are written in a sub-directory called &_log_& in Exim's spool directory.
+A path must start with a slash.
+To send to syslog, use the word &"syslog"&.
Chapter &<<CHAPlog>>& contains further details about Exim's logging, and
section &<<SECTwhelogwri>>& describes how the contents of &%log_file_path%& are
used. If this string is fixed at your installation (contains no expansion
transport driver.
-.option openssl_options main "string list" "+no_sslv2 +single_dh_use +no_ticket"
+.option openssl_options main "string list" "+no_sslv2 +no_sslv3 +single_dh_use +no_ticket +no_renegotiation"
.cindex "OpenSSL "compatibility options"
This option allows an administrator to adjust the SSL options applied
by OpenSSL to connections. It is given as a space-separated list of items,
This option is available only when Exim is built with an embedded Perl
interpreter. See chapter &<<CHAPperl>>& for details of its use.
-.option perl_startup main boolean false
+.option perl_taintmode main boolean false
.cindex "Perl"
-This Option enables the taint mode of the embedded Perl interpreter.
+This option enables the taint mode of the embedded Perl interpreter.
.option pgsql_servers main "string list" unset
that clients will use it; &"out of order"& commands that are &"expected"& do
not count as protocol errors (see &%smtp_max_synprot_errors%&).
+.option pipelining_connect_advertise_hosts main "host list&!!" *
+.cindex "pipelining" "early connection"
+.cindex "pipelining" PIPE_CONNECT
+If Exim is built with the SUPPORT_PIPE_CONNECT build option
+this option controls which hosts the facility is advertised to
+and from which pipeline early-connection (before MAIL) SMTP
+commands are acceptable.
+When used, the pipelining saves on roundtrip times.
+
+See also the &%hosts_pipe_connect%& smtp transport option.
+
+Currently the option name &"X_PIPE_CONNECT"& is used.
+
.option prdr_enable main boolean false
.cindex "PRDR" "enabling on server"
the daemon's command line.
.cindex queues named
-.cindex "named queues"
+.cindex "named queues" "resource limit"
To set limits for different named queues use
an expansion depending on the &$queue_name$& variable.
.option queue_smtp_domains main "domain list&!!" unset
.cindex "queueing incoming messages"
.cindex "message" "queueing remote deliveries"
+.cindex "first pass routing"
When this option is set, a delivery process is started whenever a message is
received, routing is performed, and local deliveries take place.
However, if any SMTP deliveries are required for domains that match
used. If the expansion yields an empty string, no &'Received:'& header line is
added to the message. Otherwise, the string should start with the text
&"Received:"& and conform to the RFC 2822 specification for &'Received:'&
-header lines. The default setting is:
+header lines.
+The default setting is:
.code
received_header_text = Received: \
${if def:sender_rcvhost {from $sender_rcvhost\n\t}\
- {${if def:sender_ident \
- {from ${quote_local_part:$sender_ident} }}\
- ${if def:sender_helo_name {(helo=$sender_helo_name)\n\t}}}}\
+ {${if def:sender_ident \
+ {from ${quote_local_part:$sender_ident} }}\
+ ${if def:sender_helo_name {(helo=$sender_helo_name)\n\t}}}}\
by $primary_hostname \
- ${if def:received_protocol {with $received_protocol}} \
- ${if def:tls_in_cipher {($tls_in_cipher)\n\t}}\
+ ${if def:received_protocol {with $received_protocol }}\
+ ${if def:tls_ver { ($tls_ver)}}\
+ ${if def:tls_in_cipher_std { tls $tls_in_cipher_std\n\t}}\
(Exim $version_number)\n\t\
${if def:sender_address \
{(envelope-from <$sender_address>)\n\t}}\
&%sender_unqualified_hosts%&, or if the message was submitted locally (not
using TCP/IP), and the &%-bnq%& option was not set.
-.option set_environment main "string list" empty
-.cindex "environment"
-This option allows to set individual environment variables that the
-currently linked libraries and programs in child processes use. The
-default list is empty,
-
.option slow_lookup_log main integer 0
.cindex "logging" "slow lookups"
smtp_etrn_command = /etc/etrn_command $domain \
$sender_host_address
.endd
+.new
+If the option is not set, the argument for the ETRN command must
+be a &'#'& followed by an address string.
+In this case an &'exim -R <string>'& command is used;
+if the ETRN ACL has set up a named-queue then &'-MCG <queue>'& is appended.
+.wen
+
A new process is created to run the command, but Exim does not wait for it to
complete. Consequently, its status cannot be checked. If the command cannot be
run, a line is written to the panic log, but the ETRN caller still receives
.cindex "TLS" "server certificate; location of"
.cindex "certificate" "server, location of"
The value of this option is expanded, and must then be a list of absolute paths to
-files which contains the server's certificates. Commonly only one file is
-needed.
+files which contain the server's certificates (in PEM format).
+Commonly only one file is needed.
The server's private key is also
assumed to be in this file if &%tls_privatekey%& is unset. See chapter
&<<CHAPTLS>>& for further details.
option in the relevant &(smtp)& transport.
&*Note*&: If you use filenames based on IP addresses, change the list
-separator in the usual way to avoid confusion under IPv6.
+separator in the usual way (&<<SECTlistsepchange>>&) to avoid confusion under IPv6.
&*Note*&: Under versions of OpenSSL preceding 1.1.1,
when a list of more than one
file is used, the &$tls_in_ourcert$& variable is unreliable.
-
-&*Note*&: OCSP stapling is not usable under OpenSSL
-when a list of more than one file is used.
+The macro "_TLS_BAD_MULTICERT_IN_OURCERT" will be defined for those versions.
If the option contains &$tls_out_sni$& and Exim is built against OpenSSL, then
if the OpenSSL build supports TLS extensions and the TLS client sends the
The value of this option is expanded and indicates the source of DH parameters
to be used by Exim.
-&*Note: The Exim Maintainers strongly recommend using a filename with site-generated
+This option is ignored for GnuTLS version 3.6.0 and later.
+The library manages parameter negotiation internally.
+
+&*Note: The Exim Maintainers strongly recommend,
+for other TLS library versions,
+using a filename with site-generated
local DH parameters*&, which has been supported across all versions of Exim. The
other specific constants available are a fallback so that even when
"unconfigured", Exim can offer Perfect Forward Secrecy in older ciphersuites in TLS.
Certificate Authority.
Usable for GnuTLS 3.4.4 or 3.3.17 or OpenSSL 1.1.0 (or later).
+The macro "_HAVE_TLS_OCSP" will be defined for those versions.
-For GnuTLS 3.5.6 or later the expanded value of this option can be a list
+For OpenSSL 1.1.0 or later, and
+for GnuTLS 3.5.6 or later the expanded value of this option can be a list
of files, to match a list given for the &%tls_certificate%& option.
The ordering of the two lists must match.
-
+The macro "_HAVE_TLS_OCSP_LIST" will be defined for those versions.
+
+The file(s) should be in DER format,
+except for GnuTLS 3.6.3 or later
+or for OpenSSL,
+when an optional filetype prefix can be used.
+The prefix must be one of "DER" or "PEM", followed by
+a single space. If one is used it sets the format for subsequent
+files in the list; the initial format is DER.
+If multiple proofs are wanted, for multiple chain elements
+(this only works under TLS1.3)
+they must be coded as a combined OCSP response.
+
+Although GnuTLS will accept PEM files with multiple separate
+PEM blobs (ie. separate OCSP responses), it sends them in the
+TLS Certificate record interleaved with the certificates of the chain;
+although a GnuTLS client is happy with that, an OpenSSL client is not.
.option tls_on_connect_ports main "string list" unset
.cindex SSMTP
.cindex "sender" "setting by untrusted user"
.cindex "untrusted user setting sender"
.cindex "user" "untrusted setting sender"
+.cindex "envelope from"
.cindex "envelope sender"
When an untrusted user submits a message to Exim using the standard input, Exim
normally creates an envelope sender address from the user's login and the
This makes the configuration file less messy, and also reduces the number of
lookups (though Exim does cache lookups).
+See also the &%set%& option below.
+
.vindex "&$sender_address_data$&"
.vindex "&$address_data$&"
The &%address_data%& facility is also useful as a means of passing information
unless you really, really know what you are doing. See also the generic
transport option of the same name.
-.option dnssec_request_domains routers "domain list&!!" unset
+.option dnssec_request_domains routers "domain list&!!" *
.cindex "MX record" "security"
.cindex "DNSSEC" "MX lookup"
.cindex "security" "MX lookup"
.option errors_to routers string&!! unset
+.cindex "envelope from"
.cindex "envelope sender"
.cindex "router" "changing address for errors"
If a router successfully handles an address, it may assign the address to a
.cindex "fallback" "hosts specified on router"
String expansion is not applied to this option. The argument must be a
colon-separated list of host names or IP addresses. The list separator can be
-changed (see section &<<SECTlistconstruct>>&), and a port can be specified with
+changed (see section &<<SECTlistsepchange>>&), and a port can be specified with
each name or address. In fact, the format of each item is exactly the same as
defined for the list of hosts in a &(manualroute)& router (see section
&<<SECTformatonehostitem>>&).
.cindex "header lines" "adding"
.cindex "router" "adding header lines"
This option specifies a list of text headers,
-newline-separated (by default, changeable in the usual way),
+newline-separated (by default, changeable in the usual way &<<SECTlistsepchange>>&),
that is associated with any addresses that are accepted by the router.
Each item is separately expanded, at routing time. However, this
option has no effect when an address is just being verified. The way in which
.cindex "header lines" "removing"
.cindex "router" "removing header lines"
This option specifies a list of text headers,
-colon-separated (by default, changeable in the usual way),
+colon-separated (by default, changeable in the usual way &<<SECTlistsepchange>>&),
that is associated with any addresses that are accepted by the router.
-Each item is separately expanded, at routing time. However, this
-option has no effect when an address is just being verified. The way in which
+However, the option has no effect when an address is just being verified.
+Each list item is separately expanded, at transport time.
+.new
+If an item ends in *, it will match any header with the given prefix.
+.wen
+The way in which
the text is used to remove header lines at transport time is described in
section &<<SECTheadersaddrem>>&. Header lines are not actually removed until
the message is in the process of being transported. This means that references
to header lines in string expansions in the transport's configuration still
&"see"& the original header lines.
-The &%headers_remove%& option is expanded after &%errors_to%& and
+The &%headers_remove%& option is handled after &%errors_to%& and
&%headers_add%&, but before &%transport%&. If an item expansion is forced to fail,
the item has no effect. Other expansion failures are treated as configuration
errors.
This behaviour can be overridden by setting &%rcpt_include_affixes%& true on
the relevant transport.
+.new
+.vindex &$local_part_prefix_v$&
+If wildcarding (above) was used then the part of the prefix matching the
+wildcard is available in &$local_part_prefix_v$&.
+.wen
+
When an address is being verified, &%local_part_prefix%& affects only the
behaviour of the router. If the callout feature of verification is in use, this
means that the full address, including the prefix, will be used during the
through the &%require_files%& list, expanding each item separately.
Because the list is split before expansion, any colons in expansion items must
-be doubled, or the facility for using a different list separator must be used.
+be doubled, or the facility for using a different list separator must be used
+(&<<SECTlistsepchange>>&).
If any expansion is forced to fail, the item is ignored. Other expansion
failures cause routing of the address to be deferred.
This option controls whether the local part is used to form the key for retry
hints for addresses that suffer temporary errors while being handled by this
-router. The default value is true for any router that has &%check_local_user%&
+router. The default value is true for any router that has any of
+&%check_local_user%&,
+&%local_parts%&,
+&%condition%&,
+&%local_part_prefix%&,
+&%local_part_suffix%&,
+&%senders%& or
+&%require_files%&
set, and false otherwise. Note that this option does not apply to hints keys
for transport delays; they are controlled by a generic transport option of the
same name.
+Failing to set this option when it is needed
+(because a remote router handles only some of the local-parts for a domain)
+can result in incorrect error messages being generated.
+
The setting of &%retry_use_local_part%& applies only to the router on which it
appears. If the router generates child addresses, they are routed
independently; this setting does not become attached to them.
matters.
+.option set routers "string list" unset
+.cindex router variables
+This option may be used multiple times on a router;
+because of this the list aspect is mostly irrelevant.
+The list separator is a semicolon but can be changed in the
+usual way.
+
+Each list-element given must be of the form &"name = value"&
+and the names used must start with the string &"r_"&.
+Values containing a list-separator should have them doubled.
+When a router runs, the strings are evaluated in order,
+to create variables which are added to the set associated with
+the address.
+The variable is set with the expansion of the value.
+The variables can be used by the router options
+(not including any preconditions)
+and by the transport.
+Later definitions of a given named variable will override former ones.
+Variable use is via the usual &$r_...$& syntax.
+
+This is similar to the &%address_data%& option, except that
+many independent variables can be used, with choice of naming.
+
+
.option translate_ip_address routers string&!! unset
.cindex "IP address" "translating"
.cindex "packet radio"
If the list is written with spaces, it must be protected with quotes.
The format of each item
in the list is described in the next section. The list separator can be changed
-as described in section &<<SECTlistconstruct>>&.
+as described in section &<<SECTlistsepchange>>&.
If the list of hosts was obtained from a &%route_list%& item, the following
variables are set during its expansion:
yield empty addresses, for example, items containing only RFC 2822 address
comments.
+.new
+.cindex "tainted data" "in filenames"
+.cindex redirect "tainted data"
+Tainted data may not be used for a filename.
+
+&*Warning*&: It is unwise to use &$local_part$& or &$domain$&
+directly for redirection,
+as they are provided by a potential attacker.
+In the examples above, &$local_part$& is used for looking up data held locally
+on the system, and not used directly (the second example derives &$home$& via
+the passsword file or database, using &$local_part$&).
+.wen
+
.section "Forward files and address verification" "SECID125"
.code
list1: :include:/opt/lists/list1
.endd
+.new
+.cindex "tainted data" "in filenames"
+.cindex redirect "tainted data"
+Tainted data may not be used for a filename.
+.wen
.next
.cindex "address redirection" "to black hole"
.cindex "delivery" "discard"
.cindex "header lines" "adding in transport"
.cindex "transport" "header lines; adding"
This option specifies a list of text headers,
-newline-separated (by default, changeable in the usual way),
+newline-separated (by default, changeable in the usual way &<<SECTlistsepchange>>&),
which are (separately) expanded and added to the header
portion of a message as it is transported, as described in section
&<<SECTheadersaddrem>>&. Additional header lines can also be specified by
.option headers_remove transports list&!! unset
.cindex "header lines" "removing"
.cindex "transport" "header lines; removing"
-This option specifies a list of header names,
-colon-separated (by default, changeable in the usual way);
-these headers are omitted from the message as it is transported, as described
-in section &<<SECTheadersaddrem>>&. Header removal can also be specified by
-routers.
+This option specifies a list of text headers,
+colon-separated (by default, changeable in the usual way &<<SECTlistsepchange>>&),
+to be removed from the message.
+However, the option has no effect when an address is just being verified.
Each list item is separately expanded.
If the result of the expansion is an empty string, or if the expansion
is forced to fail, no action is taken. Other expansion failures are treated as
errors and cause the delivery to be deferred.
+.new
+If an item ends in *, it will match any header with the given prefix.
+.wen
+
+Matching headers are omitted from the message as it is transported, as described
+in section &<<SECTheadersaddrem>>&. Header removal can also be specified by
+routers.
Unlike most options, &%headers_remove%& can be specified multiple times
for a transport; all listed headers are removed.
.option return_path transports string&!! unset
.cindex "envelope sender"
+.cindex "envelope from"
.cindex "transport" "return path; changing"
.cindex "return path" "changing in transport"
If this option is set, the string is expanded at transport time and replaces
used to determine the file or directory name for the delivery. Normally, the
contents of &$address_file$& are used in some way in the string expansion.
.endlist
+.new
+.cindex "tainted data" "in filenames"
+.cindex appendfile "tainted data"
+Tainted data may not be used for a file or directory name.
+This means that, for instance, &$local_part$& cannot be used directly
+as a component of a path. It can however be used as the key for a lookup
+which returns a path (or component).
+.wen
.cindex "Sieve filter" "configuring &(appendfile)&"
Section &<<SECID136>>& contains further information.
+This option should not be used when other message-handling software
+may duplicate messages by making hardlinks to the files. When that is done Exim
+will count the message size once for each filename, in contrast with the actual
+disk usage. When the option is not set, calculating total usage requires
+a system-call per file to get the size; the number of links is then available also
+as is used to adjust the effective size.
+
.option quota_warn_message appendfile string&!! "see below"
See below for the use of this option. If it is not set when
.option use_bsmtp appendfile boolean false
+.cindex "envelope from"
.cindex "envelope sender"
If this option is set true, &(appendfile)& writes messages in &"batch SMTP"&
format, with the envelope sender and recipient(s) included as SMTP commands. If
details of the local delivery environment and chapter &<<CHAPbatching>>&
for a discussion of local delivery batching.
+.new
+.cindex "tainted data" "in pipe command"
+.cindex pipe "tainted data"
+Tainted data may not be used for the command name.
+.wen
+
.section "Concurrent delivery" "SECID140"
If two messages arrive at almost the same time, and both are routed to a pipe
.cindex "filter" "transport filter"
.vindex "&$pipe_addresses$&"
Special handling takes place when an argument consists of precisely the text
-&`$pipe_addresses`&. This is not a general expansion variable; the only
+&`$pipe_addresses`& (no quotes).
+This is not a general expansion variable; the only
place this string is recognized is when it appears as an argument for a pipe or
transport filter command. It causes each address that is being handled to be
inserted in the argument list at that point &'as a separate argument'&. This
avoids any problems with spaces or shell metacharacters, and is of use when a
&(pipe)& transport is handling groups of addresses in a batch.
-If &%force_command%& is enabled on the transport, Special handling takes place
+If &%force_command%& is enabled on the transport, special handling takes place
for an argument that consists of precisely the text &`$address_pipe`&. It
is handled similarly to &$pipe_addresses$& above. It is expanded and each
argument is inserted in the argument list at that point
.option dkim_canon smtp string&!! unset
+DKIM signing option. For details see section &<<SECDKIMSIGN>>&.
.option dkim_domain smtp string list&!! unset
+DKIM signing option. For details see section &<<SECDKIMSIGN>>&.
.option dkim_hash smtp string&!! sha256
+DKIM signing option. For details see section &<<SECDKIMSIGN>>&.
.option dkim_identity smtp string&!! unset
+DKIM signing option. For details see section &<<SECDKIMSIGN>>&.
.option dkim_private_key smtp string&!! unset
+DKIM signing option. For details see section &<<SECDKIMSIGN>>&.
.option dkim_selector smtp string&!! unset
+DKIM signing option. For details see section &<<SECDKIMSIGN>>&.
.option dkim_strict smtp string&!! unset
+DKIM signing option. For details see section &<<SECDKIMSIGN>>&.
.option dkim_sign_headers smtp string&!! "per RFC"
+DKIM signing option. For details see section &<<SECDKIMSIGN>>&.
.option dkim_timestamps smtp string&!! unset
-DKIM signing options. For details see section &<<SECDKIMSIGN>>&.
+DKIM signing option. For details see section &<<SECDKIMSIGN>>&.
.option delay_after_cutoff smtp boolean true
details.
-.option dnssec_request_domains smtp "domain list&!!" unset
+.option dnssec_request_domains smtp "domain list&!!" *
.cindex "MX record" "security"
.cindex "DNSSEC" "MX lookup"
.cindex "security" "MX lookup"
.cindex "DNS" "DNSSEC"
DNS lookups for domains matching &%dnssec_request_domains%& will be done with
-the dnssec request bit set.
-This applies to all of the SRV, MX, AAAA, A lookup sequence.
+the dnssec request bit set. Setting this transport option is only useful if the
+transport overrides or sets the host names. See the &%dnssec_request_domains%&
+router option.
.cindex "security" "MX lookup"
.cindex "DNS" "DNSSEC"
DNS lookups for domains matching &%dnssec_require_domains%& will be done with
-the dnssec request bit set. Any returns not having the Authenticated Data bit
-(AD bit) set will be ignored and logged as a host-lookup failure.
-This applies to all of the SRV, MX, AAAA, A lookup sequence.
+the dnssec request bit set. Setting this transport option is only
+useful if the transport overrides or sets the host names. See the
+&%dnssec_require_domains%& router option.
Exim will not use the SMTP PIPELINING extension when delivering to any host
that matches this list, even if the server host advertises PIPELINING support.
+.option hosts_pipe_connect smtp "host list&!!" unset
+.cindex "pipelining" "early connection"
+.cindex "pipelining" PIPE_CONNECT
+If Exim is built with the SUPPORT_PIPE_CONNECT build option
+this option controls which to hosts the facility watched for
+and recorded, and used for subsequent connections.
+
+The retry hints database is used for the record,
+and records are subject to the &%retry_data_expire%& option.
+When used, the pipelining saves on roundtrip times.
+It also turns SMTP into a client-first protocol
+so combines well with TCP Fast Open.
+
+See also the &%pipelining_connect_advertise_hosts%& main option.
+
+Note:
+When the facility is used, the transport &%helo_data%& option
+will be expanded before the &$sending_ip_address$& variable
+is filled in.
+A check is made for the use of that variable, without the
+presence of a &"def:"& test on it, but suitably complex coding
+can avoid the check and produce unexpected results.
+You have been warned.
+
.option hosts_avoid_tls smtp "host list&!!" unset
.cindex "TLS" "avoiding for certain hosts"
message on the same connection. See section &<<SECTmulmessam>>& for an
explanation of when this might be needed.
-.option hosts_noproxy_tls smtp "host list&!!" *
+.option hosts_noproxy_tls smtp "host list&!!" unset
.cindex "TLS" "passing connection"
.cindex "multiple SMTP deliveries"
.cindex "TLS" "multiple message deliveries"
.cindex DANE "requiring for certain servers"
If built with DANE support, Exim will require that a DNSSEC-validated
TLSA record is present for any host matching the list,
-and that a DANE-verified TLS connection is made.
+and that a DANE-verified TLS connection is made. See
+the &%dnssec_request_domains%& router and transport options.
There will be no fallback to in-clear communication.
See section &<<SECDANE>>&.
.cindex "RFC 3030" "CHUNKING"
This option provides a list of servers to which, provided they announce
CHUNKING support, Exim will attempt to use BDAT commands rather than DATA.
+.new
+Unless DKIM signing is being done,
+.wen
BDAT will not be used in conjunction with a transport filter.
-.option hosts_try_dane smtp "host list&!!" unset
+.option hosts_try_dane smtp "host list&!!" *
.cindex DANE "transport options"
.cindex DANE "attempting for certain servers"
-If built with DANE support, Exim will lookup a
-TLSA record for any host matching the list.
-If found and verified by DNSSEC,
-a DANE-verified TLS connection is made to that host;
-there will be no fallback to in-clear communication.
+If built with DANE support, Exim will require that a DNSSEC-validated
+TLSA record is present for any host matching the list,
+and that a DANE-verified TLS connection is made. See
+the &%dnssec_request_domains%& router and transport options.
+There will be no fallback to in-clear communication.
See section &<<SECDANE>>&.
-.option hosts_try_fastopen smtp "host list&!!" unset
+.option hosts_try_fastopen smtp "host list&!!" *
.cindex "fast open, TCP" "enabling, in client"
.cindex "TCP Fast Open" "enabling, in client"
.cindex "RFC 7413" "TCP Fast Open"
during the expansion of the string. Forced expansion failure, or an empty
string result causes the option to be ignored. Otherwise, after expansion, the
string must be a list of IP addresses, colon-separated by default, but the
-separator can be changed in the usual way. For example:
+separator can be changed in the usual way (&<<SECTlistsepchange>>&).
+For example:
.code
interface = <; 192.168.123.123 ; 3ffe:ffff:836f::fe86:a061
.endd
If the expansion fails, or if a port number cannot be found, delivery
is deferred.
-.new
Note that at least one Linux distribution has been seen failing
to put &"smtps"& in its &"/etc/services"& file, resulting is such deferrals.
-.wen
If this option is set to &"smtps"&, the default value for the &%port%& option
changes to &"smtps"&, and the transport initiates TLS immediately after
connecting, as an outbound SSL-on-connect, instead of using STARTTLS to upgrade.
-.new
The Internet standards bodies used to strongly discourage use of this mode,
but as of RFC 8314 it is perferred over STARTTLS for message submission
(as distinct from MTA-MTA communication).
-.wen
.option retry_include_ip_address smtp boolean&!! true
If both this option and &%tls_try_verify_hosts%& are unset
operation is as if this option selected all hosts.
-.new
.option utf8_downconvert smtp integer!! unset
.cindex utf8 "address downconversion"
.cindex i18n "utf8 address downconversion"
this option controls conversion of UTF-8 in message addresses
to a-label form.
For details see section &<<SECTi18nMTA>>&.
-.wen
rewriting is applied immediately to child addresses that are generated by
redirection, unless &%no_rewrite%& is set on the router.
+.cindex "envelope from"
.cindex "envelope sender" "rewriting at transport time"
.cindex "rewriting" "at transport time"
.cindex "header lines" "rewriting at transport time"
AUTH_CRAM_MD5=yes
AUTH_CYRUS_SASL=yes
AUTH_DOVECOT=yes
+AUTH_EXTERNAL=yes
AUTH_GSASL=yes
AUTH_HEIMDAL_GSSAPI=yes
AUTH_PLAINTEXT=yes
the Cyrus SASL authentication library.
The third is an interface to Dovecot's authentication system, delegating the
work via a socket interface.
-The fourth provides an interface to the GNU SASL authentication library, which
+The fourth provides for negotiation of authentication done via non-SMTP means,
+as defined by RFC 4422 Appendix A.
+The fifth provides an interface to the GNU SASL authentication library, which
provides mechanisms but typically not data sources.
-The fifth provides direct access to Heimdal GSSAPI, geared for Kerberos, but
+The sixth provides direct access to Heimdal GSSAPI, geared for Kerberos, but
supporting setting a server keytab.
-The sixth can be configured to support
+The seventh can be configured to support
the PLAIN authentication mechanism (RFC 2595) or the LOGIN mechanism, which is
-not formally documented, but used by several MUAs. The seventh authenticator
+not formally documented, but used by several MUAs.
+The eighth authenticator
supports Microsoft's &'Secure Password Authentication'& mechanism.
-The eighth is an Exim authenticator but not an SMTP one;
+The last is an Exim authenticator but not an SMTP one;
instead it can use information from a TLS negotiation.
The authenticators are configured using the same syntax as other drivers (see
.cindex authentication "expansion item"
Successful authentication sets up information used by the
-&$authresults$& expansion item.
+&%authresults%& expansion item.
use unencrypted plain text, you should not use the same passwords for SMTP
connections as you do for login accounts.
-.section "Plaintext options" "SECID171"
+.section "Avoiding cleartext use" "SECTplain_TLS"
+The following generic option settings will disable &(plaintext)& authenticators when
+TLS is not being used:
+.code
+ server_advertise_condition = ${if def:tls_in_cipher }
+ client_condition = ${if def:tls_out_cipher}
+.endd
+
+&*Note*&: a plaintext SMTP AUTH done inside TLS is not vulnerable to casual snooping,
+but is still vulnerable to a Man In The Middle attack unless certificates
+(including their names) have been properly verified.
+
+.section "Plaintext server options" "SECID171"
.cindex "options" "&(plaintext)& authenticator (server)"
When configured as a server, &(plaintext)& uses the following options:
This is actually a global authentication option, but it must be set in order to
configure the &(plaintext)& driver as a server. Its use is described below.
-.option server_prompts plaintext string&!! unset
+.option server_prompts plaintext "string list&!!" unset
The contents of this option, after expansion, must be a colon-separated list of
prompt strings. If expansion fails, a temporary authentication rejection is
given.
.section "The PLAIN authentication mechanism" "SECID172"
.cindex "PLAIN authentication mechanism"
-.cindex "authentication" "PLAIN mechanism"
+.cindex authentication PLAIN
.cindex "binary zero" "in &(plaintext)& authenticator"
The PLAIN authentication mechanism (RFC 2595) specifies that three strings be
sent as one item of data (that is, one combined string containing two NUL
.section "The LOGIN authentication mechanism" "SECID173"
.cindex "LOGIN authentication mechanism"
-.cindex "authentication" "LOGIN mechanism"
+.cindex authentication LOGIN
The LOGIN authentication mechanism is not documented in any RFC, but is in use
in a number of programs. No data is sent with the AUTH command. Instead, a
user name and password are supplied separately, in response to prompts. The
.scindex IIDcramauth1 "&(cram_md5)& authenticator"
.scindex IIDcramauth2 "authenticators" "&(cram_md5)&"
.cindex "CRAM-MD5 authentication mechanism"
-.cindex "authentication" "CRAM-MD5 mechanism"
+.cindex authentication CRAM-MD5
The CRAM-MD5 authentication mechanism is described in RFC 2195. The server
sends a challenge string to the client, and the response consists of a user
name and the CRAM-MD5 digest of the challenge string combined with a secret
.scindex IIDdcotauth1 "&(dovecot)& authenticator"
.scindex IIDdcotauth2 "authenticators" "&(dovecot)&"
This authenticator is an interface to the authentication facility of the
-Dovecot POP/IMAP server, which can support a number of authentication methods.
+Dovecot 2 POP/IMAP server, which can support a number of authentication methods.
Note that Dovecot must be configured to use auth-client not auth-userdb.
If you are using Dovecot to authenticate POP/IMAP clients, it might be helpful
to use the same mechanisms for SMTP authentication. This is a server
connection, a client certificate has been verified, the &"valid-client-cert"&
option is passed. When authentication succeeds, the identity of the user
who authenticated is placed in &$auth1$&.
+
+.new
+The Dovecot configuration to match the above wil look
+something like:
+.code
+conf.d/10-master.conf :-
+
+service auth {
+...
+#SASL
+ unix_listener auth-client {
+ mode = 0660
+ user = mail
+ }
+...
+}
+
+conf.d/10-auth.conf :-
+
+auth_mechanisms = plain login ntlm
+.endd
+.wen
+
.ecindex IIDdcotauth1
.ecindex IIDdcotauth2
.cindex "authentication" "LOGIN"
.cindex "authentication" "DIGEST-MD5"
.cindex "authentication" "CRAM-MD5"
-.cindex "authentication" "SCRAM-SHA-1"
-The &(gsasl)& authenticator provides server integration for the GNU SASL
+.cindex "authentication" "SCRAM family"
+The &(gsasl)& authenticator provides integration for the GNU SASL
library and the mechanisms it provides. This is new as of the 4.80 release
and there are a few areas where the library does not let Exim smoothly
scale to handle future authentication mechanisms, so no guarantee can be
made that any particular new authentication mechanism will be supported
without code changes in Exim.
-Exim's &(gsasl)& authenticator does not have client-side support at this
-time; only the server-side support is implemented. Patches welcome.
+.new
+The library is expected to add support in an upcoming
+realease for the SCRAM-SHA-256 method.
+The macro _HAVE_AUTH_GSASL_SCRAM_SHA_256 will be defined
+when this happens.
+
+
+.option client_authz gsasl string&!! unset
+This option can be used to supply an &'authorization id'&
+which is different to the &'authentication_id'& provided
+by &%client_username%& option.
+If unset or (after expansion) empty it is not used,
+which is the common case.
+
+.option client_channelbinding gsasl boolean false
+See &%server_channelbinding%& below.
+
+.option client_password gsasl string&!! unset
+This option is exapanded before use, and should result in
+the password to be used, in clear.
+
+.option client_username gsasl string&!! unset
+This option is exapanded before use, and should result in
+the account name to be used.
+.wen
+
+.new
+.option client_spassword gsasl string&!! unset
+If a SCRAM mechanism is being used and this option is set
+it is used in preference to &%client_password%&.
+The value after expansion should be
+a 40 (for SHA-1) or 64 (for SHA-256) character string
+with the PBKDF2-prepared password, hex-encoded.
+Note that this value will depend on the salt and iteration-count
+supplied by the server.
+.wen
+
.option server_channelbinding gsasl boolean false
-Do not set this true without consulting a cryptographic engineer.
+Do not set this true and rely on the properties
+without consulting a cryptographic engineer.
Some authentication mechanisms are able to use external context at both ends
of the session to bind the authentication to that context, and fail the
non-issue, as a man-in-the-middle attack will cause the correct client and
server to see different identifiers and authentication will fail.
-This is currently only supported when using the GnuTLS library. This is
+.new
+This is
only usable by mechanisms which support "channel binding"; at time of
writing, that's the SCRAM family.
+When using this feature the "-PLUS" variants of the method names need to be used.
+.wen
This defaults off to ensure smooth upgrade across Exim releases, in case
this option causes some clients to start failing. Some future release
of Exim might have switched the default to be true.
-However, Channel Binding in TLS has proven to be broken in current versions.
+However, Channel Binding in TLS has proven to be vulnerable in current versions.
Do not plan to rely upon this feature for security, ever, without consulting
with a subject matter expert (a cryptographic engineer).
Some mechanisms will use this data.
-.option server_scram_iter gsasl string&!! unset
+.option server_scram_iter gsasl string&!! 4096
This option provides data for the SCRAM family of mechanisms.
-&$auth1$& is not available at evaluation time.
-(This may change, as we receive feedback on use)
-
+.new
+The &$auth1$&, &$auth2$& and &$auth3$& variables are available
+when this option is expanded.
+
+The result of expansion should be a decimal number,
+and represents both a lower-bound on the security, and
+a compute cost factor imposed on the client
+(if it does not cache results, or the server changes
+either the iteration count or the salt).
+A minimum value of 4096 is required by the standards
+for all current SCRAM mechanism variants.
+.wen
.option server_scram_salt gsasl string&!! unset
This option provides data for the SCRAM family of mechanisms.
-&$auth1$& is not available at evaluation time.
-(This may change, as we receive feedback on use)
+.new
+The &$auth1$&, &$auth2$& and &$auth3$& variables are available
+when this option is expanded.
+The value should be a base64-encoded string,
+of random data typically 4-to-16 bytes long.
+If unset or empty after expansion the library will provides a value for the
+protocol conversation.
+.wen
+
+
+.new
+.option server_key gsasl string&!! unset
+.option server_skey gsasl string&!! unset
+These options can be used for the SCRAM family of mechanisms
+to provide stored information related to a password,
+the storage of which is preferable to plaintext.
+
+&%server_key%& is the value defined in the SCRAM standards as ServerKey;
+&%server_skey%& is StoredKey.
+
+They are only available for version 1.9.0 (or later) of the gsasl library.
+When this is so, the macros
+_OPT_AUTHENTICATOR_GSASL_SERVER_KEY
+and _HAVE_AUTH_GSASL_SCRAM_S_KEY
+will be defined.
+
+The &$authN$& variables are available when these options are expanded.
+
+If set, the results of expansion should for each
+should be a 28 (for SHA-1) or 44 (for SHA-256) character string
+of base64-coded data, and will be used in preference to the
+&%server_password%& option.
+If unset or not of the right length, &%server_password%& will be used.
+
+The libgsasl library release includes a utility &'gsasl'& which can be used
+to generate these values.
+.wen
.option server_service gsasl string &`smtp`&
+. ////////////////////////////////////////////////////////////////////////////
+. ////////////////////////////////////////////////////////////////////////////
+
+.chapter "The external authenticator" "CHAPexternauth"
+.scindex IIDexternauth1 "&(external)& authenticator"
+.scindex IIDexternauth2 "authenticators" "&(external)&"
+.cindex "authentication" "Client Certificate"
+.cindex "authentication" "X509"
+.cindex "Certificate-based authentication"
+The &(external)& authenticator provides support for
+authentication based on non-SMTP information.
+The specification is in RFC 4422 Appendix A
+(&url(https://tools.ietf.org/html/rfc4422)).
+It is only a transport and negotiation mechanism;
+the process of authentication is entirely controlled
+by the server configuration.
+
+The client presents an identity in-clear.
+It is probably wise for a server to only advertise,
+and for clients to only attempt,
+this authentication method on a secure (eg. under TLS) connection.
+
+One possible use, compatible with the
+K-9 Mail Andoid client (&url(https://k9mail.github.io/)),
+is for using X509 client certificates.
+
+It thus overlaps in function with the TLS authenticator
+(see &<<CHAPtlsauth>>&)
+but is a full SMTP SASL authenticator
+rather than being implicit for TLS-connection carried
+client certificates only.
+
+The examples and discussion in this chapter assume that
+client-certificate authentication is being done.
+
+The client must present a certificate,
+for which it must have been requested via the
+&%tls_verify_hosts%& or &%tls_try_verify_hosts%& main options
+(see &<<CHAPTLS>>&).
+For authentication to be effective the certificate should be
+verifiable against a trust-anchor certificate known to the server.
+
+.section "External options" "SECTexternsoptions"
+.cindex "options" "&(external)& authenticator (server)"
+The &(external)& authenticator has two server options:
+
+.option server_param2 external string&!! unset
+.option server_param3 external string&!! unset
+.cindex "variables (&$auth1$& &$auth2$& etc)" "in &(external)& authenticator"
+These options are expanded before the &%server_condition%& option
+and the result are placed in &$auth2$& and &$auth3$& resectively.
+If the expansion is forced to fail, authentication fails. Any other expansion
+failure causes a temporary error code to be returned.
+
+They can be used to clarify the coding of a complex &%server_condition%&.
+
+.section "Using external in a server" "SECTexternserver"
+.cindex "AUTH" "in &(external)& authenticator"
+.cindex "numerical variables (&$1$& &$2$& etc)" &&&
+ "in &(external)& authenticator"
+.vindex "&$auth1$&, &$auth2$&, etc"
+.cindex "base64 encoding" "in &(external)& authenticator"
+
+When running as a server, &(external)& performs the authentication test by
+expanding a string. The data sent by the client with the AUTH command, or in
+response to subsequent prompts, is base64 encoded, and so may contain any byte
+values when decoded. The decoded value is treated as
+an identity for authentication and
+placed in the expansion variable &$auth1$&.
+
+For compatibility with previous releases of Exim, the value is also placed in
+the expansion variable &$1$&. However, the use of this
+variable for this purpose is now deprecated, as it can lead to confusion in
+string expansions that also use them for other things.
+
+.vindex "&$authenticated_id$&"
+Once an identity has been received,
+&%server_condition%& is expanded. If the expansion is forced to fail,
+authentication fails. Any other expansion failure causes a temporary error code
+to be returned. If the result of a successful expansion is an empty string,
+&"0"&, &"no"&, or &"false"&, authentication fails. If the result of the
+expansion is &"1"&, &"yes"&, or &"true"&, authentication succeeds and the
+generic &%server_set_id%& option is expanded and saved in &$authenticated_id$&.
+For any other result, a temporary error code is returned, with the expanded
+string as the error text.
+
+Example:
+.code
+ext_ccert_san_mail:
+ driver = external
+ public_name = EXTERNAL
+
+ server_advertise_condition = $tls_in_certificate_verified
+ server_param2 = ${certextract {subj_altname,mail,>:} \
+ {$tls_in_peercert}}
+ server_condition = ${if forany {$auth2} \
+ {eq {$item}{$auth1}}}
+ server_set_id = $auth1
+.endd
+This accepts a client certificate that is verifiable against any
+of your configured trust-anchors
+(which usually means the full set of public CAs)
+and which has a mail-SAN matching the claimed identity sent by the client.
+
+&*Note*&: up to TLS1.2, the client cert is on the wire in-clear, including the SAN.
+The account name is therefore guessable by an opponent.
+TLS 1.3 protects both server and client certificates, and is not vulnerable
+in this way.
+
+
+.section "Using external in a client" "SECTexternclient"
+.cindex "options" "&(external)& authenticator (client)"
+The &(external)& authenticator has one client option:
+
+.option client_send external string&!! unset
+This option is expanded and sent with the AUTH command as the
+identity being asserted.
+
+Example:
+.code
+ext_ccert:
+ driver = external
+ public_name = EXTERNAL
+
+ client_condition = ${if !eq{$tls_out_cipher}{}}
+ client_send = myaccount@smarthost.example.net
+.endd
+
+
+.ecindex IIDexternauth1
+.ecindex IIDexternauth2
+
+
+
+
+
. ////////////////////////////////////////////////////////////////////////////
. ////////////////////////////////////////////////////////////////////////////
.section "OpenSSL vs GnuTLS" "SECTopenvsgnu"
.cindex "TLS" "OpenSSL &'vs'& GnuTLS"
-The first TLS support in Exim was implemented using OpenSSL. Support for GnuTLS
-followed later, when the first versions of GnuTLS were released. To build Exim
-to use GnuTLS, you need to set
+TLS is supported in Exim using either the OpenSSL or GnuTLS library.
+To build Exim to use OpenSSL you need to set
.code
-USE_GNUTLS=yes
+USE_OPENSSL=yes
.endd
-in Local/Makefile, in addition to
+in Local/Makefile.
+
+To build Exim to use GnuTLS, you need to set
.code
-SUPPORT_TLS=yes
+USE_GNUTLS=yes
.endd
+in Local/Makefile.
+
You must also set TLS_LIBS and TLS_INCLUDE appropriately, so that the
include files and libraries for GnuTLS can be found.
.oindex "&%tls_require_ciphers%&" "OpenSSL"
There is a function in the OpenSSL library that can be passed a list of cipher
suites before the cipher negotiation takes place. This specifies which ciphers
-.new
are acceptable for TLS versions prior to 1.3.
-.wen
The list is colon separated and may contain names like
DES-CBC3-SHA. Exim passes the expanded value of &%tls_require_ciphers%&
directly to this function call.
tls_require_ciphers = ECDSA:RSA:!COMPLEMENTOFDEFAULT
.endd
-.new
For TLS version 1.3 the control available is less fine-grained
and Exim does not provide access to it at present.
The value of the &%tls_require_ciphers%& option is ignored when
.code
TLS_AES_256_GCM_SHA384:TLS_CHACHA20_POLY1305_SHA256:TLS_AES_128_GCM_SHA256
.endd
-.wen
.section "Requiring specific ciphers or other parameters in GnuTLS" &&&
-.section "Configuring an Exim client to use TLS" "SECID185"
+.section "Configuring an Exim client to use TLS" "SECTclientTLS"
.cindex "cipher" "logging"
.cindex "log" "TLS cipher"
.cindex "log" "distinguished name"
if it requests it. If the server is Exim, it will request a certificate only if
&%tls_verify_hosts%& or &%tls_try_verify_hosts%& matches the client.
+&*Note*&: Do not use a certificate which has the OCSP-must-staple extension,
+for client use (they are usable for server use).
+As the TLS protocol has no means for the client to staple before TLS 1.3 it will result
+in failed connections.
+
If the &%tls_verify_certificates%& option is set on the &(smtp)& transport, it
specifies a collection of expected server certificates.
These may be
attacks in the string (&`../`& or SQL), and ensuring that a valid filename
can always be referenced; it is important to remember that &$tls_in_sni$& is
arbitrary unverified data provided prior to authentication.
-Further, the initial certificate is loaded before SNI is arrived, so
+Further, the initial certificate is loaded before SNI has arrived, so
an expansion for &%tls_certificate%& must have a default which is used
when &$tls_in_sni$& is empty.
in &_Local/Makefile_&.
If it has been included, the macro "_HAVE_DANE" will be defined.
-The TLSA record for the server may have "certificate usage" of DANE-TA(2) or DANE-EE(3).
+A TLSA record consist of 4 fields, the "Certificate Usage", the
+"Selector", the "Matching type", and the "Certificate Association Data".
+For a detailed description of the TLSA record see
+&url(https://tools.ietf.org/html/rfc7671#page-5,RFC 7671).
+
+The TLSA record for the server may have "Certificate Usage" (1st) field of DANE-TA(2) or DANE-EE(3).
These are the "Trust Anchor" and "End Entity" variants.
The latter specifies the End Entity directly, i.e. the certificate involved is that of the server
(and if only DANE-EE is used then it should be the sole one transmitted during the TLS handshake);
all of which point to a single TLSA record.
DANE-TA and DANE-EE can both be used together.
-.new
Our recommendation is to use DANE with a certificate from a public CA,
because this enables a variety of strategies for remote clients to verify
your certificate.
If you're not already using a private CA, or it doesn't meet these
requirements, then we encourage you to avoid all these issues and use a public
CA such as &url(https://letsencrypt.org/,Let's Encrypt) instead.
-.wen
-The TLSA record should have a Selector field of SPKI(1) and a Matching Type field of SHA2-512(2).
+The TLSA record should have a "Selector" (2nd) field of SPKI(1) and
+a "Matching Type" (3rd) field of SHA2-512(2).
-At the time of writing, &url(https://www.huque.com/bin/gen_tlsa)
-is useful for quickly generating TLSA records; and commands like
+For the "Certificate Authority Data" (4th) field, commands like
.code
- openssl x509 -in -pubkey -noout <certificate.pem \
+ openssl x509 -pubkey -noout <certificate.pem \
| openssl rsa -outform der -pubin 2>/dev/null \
| openssl sha512 \
| awk '{print $2}'
.endd
-are workable for 4th-field hashes.
+are workable to create a hash of the certificate's public key.
+
+An example TLSA record for DANE-EE(3), SPKI(1), and SHA-512 (2) looks like
+
+.code
+ _25._tcp.mail.example.com. TLSA 3 1 2 8BA8A336E...
+.endd
+
+At the time of writing, &url(https://www.huque.com/bin/gen_tlsa)
+is useful for quickly generating TLSA records.
+
For use with the DANE-TA model, server certificates must have a correct name (SubjectName or SubjectAltName).
-.new
The Certificate issued by the CA published in the DANE-TA model should be
issued using a strong hash algorithm.
Exim, and importantly various other MTAs sending to you, will not
libraries.
This means no MD5 and no SHA-1. SHA2-256 is the minimum for reliable
interoperability (and probably the maximum too, in 2018).
-.wen
The use of OCSP-stapling should be considered, allowing for fast revocation of certificates (which would otherwise
be limited by the DNS TTL on the TLSA records). However, this is likely to only be usable with DANE-TA. NOTE: the
For client-side DANE there are three new smtp transport options, &%hosts_try_dane%&, &%hosts_require_dane%&
and &%dane_require_tls_ciphers%&.
-The require variant will result in failure if the target host is not DNSSEC-secured.
+The &"require"& variant will result in failure if the target host is not
+DNSSEC-secured. To get DNSSEC-secured hostname resolution, use
+the &%dnssec_request_domains%& router or transport option.
DANE will only be usable if the target host has DNSSEC-secured MX, A and TLSA records.
If DANE is not usable, whether requested or not, and CA-anchored
verification evaluation is wanted, the above variables should be set appropriately.
-Currently the &%dnssec_request_domains%& must be active and &%dnssec_require_domains%& is ignored.
+The router and transport option &%dnssec_request_domains%& must not be
+set to &"never"&, and &%dnssec_require_domains%& is ignored.
If verification was successful using DANE then the "CV" item in the delivery log line will show as "CV=dane".
It can be at the end of an &%accept%& statement:
.code
accept ...some conditions
- control = queue_only
+ control = queue
.endd
In this case, the control is applied when this statement yields &"accept"&, in
other words, when the conditions are all true.
It can be in the middle of an &%accept%& statement:
.code
accept ...some conditions...
- control = queue_only
+ control = queue
...some more conditions...
.endd
If the first set of conditions are true, the control is applied, even if the
the operation and configuration of DKIM, see section &<<SECDKIM>>&.
+.vitem &*control&~=&~dmarc_disable_verify*&
+.cindex "disable DMARC verify"
+.cindex "DMARC" "disable verify"
+This control turns off DMARC verification processing entirely. For details on
+the operation and configuration of DMARC, see section &<<SECDMARC>>&.
+
+
.vitem &*control&~=&~dscp/*&<&'value'&>
.cindex "&ACL;" "setting DSCP value"
.cindex "DSCP" "inbound"
controlled by &%acl_smtp_connect%& or &%acl_smtp_helo%&. See also
&%pipelining_advertise_hosts%&.
-.vitem &*control&~=&~queue_only*&
+.new
+.vitem &*control&~=&~queue/*&<&'options'&>* &&&
+ &*control&~=&~queue_only*&
+.oindex "&%queue%&"
.oindex "&%queue_only%&"
.cindex "queueing incoming messages"
+.cindex queueing "forcing in ACL"
+.cindex "first pass routing"
This control is permitted only for the MAIL, RCPT, DATA, and non-SMTP ACLs, in
other words, only when a message is being received. If the message is accepted,
it is placed on Exim's queue and left there for delivery by a subsequent queue
-runner. No immediate delivery process is started. In other words, it has the
-effect as the &%queue_only%& global option. However, the control applies only
-to the current message, not to any subsequent ones that may be received in the
-same SMTP connection.
+runner.
+If used with no options set,
+no immediate delivery process is started. In other words, it has the
+effect as the &%queue_only%& global option or &'-odq'& command-line option.
+
+If the &'first_pass_route'& option is given then
+the behaviour is like the command-line &'-oqds'& option;
+a delivery process is started which stops short of making
+any SMTP delivery. The benefit is that the hints database will be updated for
+the message being waiting for a specific host, and a later queue run will be
+able to send all such messages on a single connection.
+
+The control only applies to the current message, not to any subsequent ones that
+ may be received in the same SMTP connection.
+.wen
.vitem &*control&~=&~submission/*&<&'options'&>
.cindex "message" "submission"
.cindex "&ACL;" "virus scanning"
.cindex "&ACL;" "scanning for viruses"
This condition is available only when Exim is compiled with the
-content-scanning extension. It causes the incoming message to be scanned for
+content-scanning extension
+and only after a DATA command.
+It causes the incoming message to be scanned for
viruses. For details, see chapter &<<CHAPexiscan>>&.
.vitem &*mime_regex&~=&~*&<&'list&~of&~regular&~expressions'&>
attempt to verify the HELO/EHLO contents, it is carried out when this
condition is encountered. See the description of the &%helo_verify_hosts%& and
&%helo_try_verify_hosts%& options for details of how to request verification
-independently of this condition.
+independently of this condition, and for detail of the verification.
For SMTP input that does not come over TCP/IP (the &%-bs%& command line
option), this condition is always true.
-.vitem &*verify&~=&~not_blind*&
+.vitem &*verify&~=&~not_blind/*&<&'options'&>
.cindex "verifying" "not blind"
.cindex "bcc recipients, verifying none"
This condition checks that there are no blind (bcc) recipients in the message.
&'Resent-Cc:'& header lines exist, they are also checked. This condition can be
used only in a DATA or non-SMTP ACL.
+There is one possible option, &`case_insensitive`&. If this is present then
+local parts are checked case-insensitively.
+
There are, of course, many legitimate messages that make use of blind (bcc)
recipients. This check should not be used on its own for blocking messages.
The &%leaky%& (default) option means that the client's recorded rate is not
updated if it is above the limit. The effect of this is that Exim measures the
client's average rate of successfully sent email,
-.new
up to the given limit.
This is appropriate if the countermeasure when the condition is true
consists of refusing the message, and
is generally the better choice if you have clients that retry automatically.
If the action when true is anything more complex then this option is
likely not what is wanted.
-.wen
The &%strict%& option means that the client's recorded rate is always
updated. The effect of this is that Exim measures the client's average rate
The main use of these variables is expected to be to distinguish between
rejections of MAIL and rejections of RCPT in callouts.
-.new
The above variables may also be set after a &*successful*&
address verification to:
.ilist
&%random%&: A random local-part callout succeeded
.endlist
-.wen
specialized interfaces for &"daemon"& type virus scanners, which are resident
in memory and thus are much faster.
+Since message data needs to have arrived,
+the condition may be only called in ACL defined by
+&%acl_smtp_data%&,
+&%acl_smtp_data_prdr%&,
+&%acl_smtp_mime%& or
+&%acl_smtp_dkim%&
+
A timeout of 2 minutes is applied to a scanner call (by default);
if it expires then a defer action is taken.
condition succeeds if a virus is found and its name matches the regular
expression. This allows you to take special actions on certain types of virus.
Note that &"/"& characters in the RE must be doubled due to the list-processing,
-unless the separator is changed (in the usual way).
+unless the separator is changed (in the usual way &<<SECTlistsepchange>>&).
.endlist
You can append a &`defer_ok`& element to the &%malware%& argument list to accept
you must set the &%spamd_address%& option in the global part of the Exim
configuration as follows (example):
.code
-spamd_address = 192.168.99.45 387
+spamd_address = 192.168.99.45 783
.endd
The SpamAssassin protocol relies on a TCP half-close from the client.
If your SpamAssassin client side is running a Linux system with an
You can have multiple &%spamd%& servers to improve scalability. These can
reside on other hardware reachable over the network. To specify multiple
&%spamd%& servers, put multiple address/port pairs in the &%spamd_address%&
-option, separated with colons (the separator can be changed in the usual way):
+option, separated with colons (the separator can be changed in the usual way &<<SECTlistsepchange>>&):
.code
spamd_address = 192.168.2.10 783 : \
192.168.2.11 783 : \
Unix and TCP socket specifications may be mixed in any order.
Each element of the list is a list itself, space-separated by default
-and changeable in the usual way; take care to not double the separator.
+and changeable in the usual way (&<<SECTlistsepchange>>&);
+take care to not double the separator.
For TCP socket specifications a host name or IP (v4 or v6, but
subject to list-separator quoting rules) address can be used,
available in the MIME ACL:
.vlist
+.vitem &$mime_anomaly_level$& &&&
+ &$mime_anomaly_text$&
+.vindex &$mime_anomaly_level$&
+.vindex &$mime_anomaly_text$&
+If there are problems decoding, these variables contain information on
+the detected issue.
+
.vitem &$mime_boundary$&
-If the current part is a multipart (see &$mime_is_multipart$&) below, it should
+.vindex &$mime_boundary$&
+If the current part is a multipart (see &$mime_is_multipart$& below), it should
have a boundary string, which is stored in this variable. If the current part
has no boundary parameter in the &'Content-Type:'& header, this variable
contains the empty string.
.vitem &$mime_charset$&
+.vindex &$mime_charset$&
This variable contains the character set identifier, if one was found in the
&'Content-Type:'& header. Examples for charset identifiers are:
.code
case-insensitively.
.vitem &$mime_content_description$&
+.vindex &$mime_content_description$&
This variable contains the normalized content of the &'Content-Description:'&
header. It can contain a human-readable description of the parts content. Some
implementations repeat the filename for attachments here, but they are usually
only used for display purposes.
.vitem &$mime_content_disposition$&
+.vindex &$mime_content_disposition$&
This variable contains the normalized content of the &'Content-Disposition:'&
header. You can expect strings like &"attachment"& or &"inline"& here.
.vitem &$mime_content_id$&
+.vindex &$mime_content_id$&
This variable contains the normalized content of the &'Content-ID:'& header.
This is a unique ID that can be used to reference a part from another part.
.vitem &$mime_content_size$&
+.vindex &$mime_content_size$&
This variable is set only after the &%decode%& modifier (see above) has been
successfully run. It contains the size of the decoded part in kilobytes. The
size is always rounded up to full kilobytes, so only a completely empty part
has a &$mime_content_size$& of zero.
.vitem &$mime_content_transfer_encoding$&
+.vindex &$mime_content_transfer_encoding$&
This variable contains the normalized content of the
&'Content-transfer-encoding:'& header. This is a symbolic name for an encoding
type. Typical values are &"base64"& and &"quoted-printable"&.
.vitem &$mime_content_type$&
+.vindex &$mime_content_type$&
If the MIME part has a &'Content-Type:'& header, this variable contains its
value, lowercased, and without any options (like &"name"& or &"charset"&). Here
are some examples of popular MIME types, as they may appear in this variable:
empty string.
.vitem &$mime_decoded_filename$&
+.vindex &$mime_decoded_filename$&
This variable is set only after the &%decode%& modifier (see above) has been
successfully run. It contains the full path and filename of the file
containing the decoded data.
.cindex "RFC 2047"
.vlist
.vitem &$mime_filename$&
+.vindex &$mime_filename$&
This is perhaps the most important of the MIME variables. It contains a
proposed filename for an attachment, if one was found in either the
&'Content-Type:'& or &'Content-Disposition:'& headers. The filename will be
found, this variable contains the empty string.
.vitem &$mime_is_coverletter$&
+.vindex &$mime_is_coverletter$&
This variable attempts to differentiate the &"cover letter"& of an e-mail from
attached data. It can be used to clamp down on flashy or unnecessarily encoded
content in the cover letter, while not restricting attachments at all.
condition = $mime_is_coverletter
condition = ${if eq{$mime_content_type}{text/html}{1}{0}}
.endd
+
.vitem &$mime_is_multipart$&
+.vindex &$mime_is_multipart$&
This variable has the value 1 (true) when the current part has the main type
&"multipart"&, for example, &"multipart/alternative"& or &"multipart/mixed"&.
Since multipart entities only serve as containers for other parts, you may not
want to carry out specific actions on them.
.vitem &$mime_is_rfc822$&
+.vindex &$mime_is_rfc822$&
This variable has the value 1 (true) if the current part is not a part of the
checked message itself, but part of an attached message. Attached message
decoding is fully recursive.
.vitem &$mime_part_count$&
+.vindex &$mime_part_count$&
This variable is a counter that is raised for each processed MIME part. It
starts at zero for the very first part (which is usually a multipart). The
counter is per-message, so it is reset when processing RFC822 attachments (see
.cindex "&[local_scan()]& function" "building Exim to use"
To make use of the local scan function feature, you must tell Exim where your
function is before building Exim, by setting
-.new
both HAVE_LOCAL_SCAN and
-.wen
LOCAL_SCAN_SOURCE in your
&_Local/Makefile_&. A recommended place to put it is in the &_Local_&
directory, so you might set
HAVE_LOCAL_SCAN=yes
LOCAL_SCAN_SOURCE=Local/local_scan.c
.endd
-for example. The function must be called &[local_scan()]&. It is called by
+for example. The function must be called &[local_scan()]&;
+.new
+the source file(s) for it should first #define LOCAL_SCAN
+and then #include "local_scan.h".
+.wen
+It is called by
Exim after it has received a message, when the success return code is about to
be sent. This is after all the ACLs have been run. The return code from your
function controls whether the message is actually accepted or not. There is a
.cindex &%dlfunc%& "API description"
You must include this line near the start of your code:
.code
+#define LOCAL_SCAN
#include "local_scan.h"
.endd
This header file defines a number of variables and other values, and the
prototype for the function itself. Exim is coded to use unsigned char values
almost exclusively, and one of the things this header defines is a shorthand
for &`unsigned char`& called &`uschar`&.
-It also contains the following macro definitions, to simplify casting character
+It also makes available the following macro definitions, to simplify casting character
strings and pointers to character strings:
.code
#define CS (char *)
This function is used in conjunction with &'smtp_printf()'&, as described
below.
-.vitem &*void&~smtp_printf(char&~*,&~...)*&
-The arguments of this function are like &[printf()]&; it writes to the SMTP
+.vitem &*void&~smtp_printf(char&~*,BOOL,&~...)*&
+The arguments of this function are almost like &[printf()]&; it writes to the SMTP
output stream. You should use this function only when there is an SMTP output
stream, that is, when the incoming message is being received via interactive
SMTP. This is the case when &%smtp_input%& is TRUE and &%smtp_batched_input%&
If an SMTP TLS connection is established, &'smtp_printf()'& uses the TLS
output function, so it can be used for all forms of SMTP connection.
+The second argument is used to request that the data be buffered
+(when TRUE) or flushed (along with any previously buffered, when FALSE).
+This is advisory only, but likely to save on system-calls and packets
+sent when a sequence of calls to the function are made.
+
+The argument was added in Exim version 4.90 - changing the API/ABI.
+Nobody noticed until 4.93 was imminent, at which point the
+ABI version number was incremented.
+
Strings that are written by &'smtp_printf()'& from within &[local_scan()]&
must start with an appropriate response code: 550 if you are going to return
LOCAL_SCAN_REJECT, 451 if you are going to return
multiple output lines.
The &'smtp_printf()'& function does not return any error indication, because it
-does not automatically flush pending output, and therefore does not test
+does not
+guarantee a flush of
+pending output, and therefore does not test
the state of the stream. (In the main code of Exim, flushing and error
detection is done when Exim is ready for the next SMTP input command.) If
you want to flush the output and check for an error (for example, the
arguments. It flushes the output stream, and returns a non-zero value if there
is an error.
-.vitem &*void&~*store_get(int)*&
+.new
+.vitem &*void&~*store_get(int,BOOL)*&
This function accesses Exim's internal store (memory) manager. It gets a new
-chunk of memory whose size is given by the argument. Exim bombs out if it ever
+chunk of memory whose size is given by the first argument.
+The second argument should be given as TRUE if the memory will be used for
+data possibly coming from an attacker (eg. the message content),
+FALSE if it is locally-sourced.
+Exim bombs out if it ever
runs out of memory. See the next section for a discussion of memory handling.
+.wen
-.vitem &*void&~*store_get_perm(int)*&
+.vitem &*void&~*store_get_perm(int,BOOL)*&
This function is like &'store_get()'&, but it always gets memory from the
permanent pool. See the next section for a discussion of memory handling.
.section "Setting an errors address in a system filter" "SECID217"
+.cindex "envelope from"
.cindex "envelope sender"
In a system filter, if a &%deliver%& command is followed by
.code
.cindex "sender" "address"
.oindex "&%uucp_from_pattern%&"
.oindex "&%uucp_from_sender%&"
+.cindex "envelope from"
.cindex "envelope sender"
.cindex "Sendmail compatibility" "&""From""& line"
Messages that have come from UUCP (and some other applications) often begin
.section "Variable Envelope Return Paths (VERP)" "SECTverp"
.cindex "VERP"
.cindex "Variable Envelope Return Paths"
+.cindex "envelope from"
.cindex "envelope sender"
Variable Envelope Return Paths &-- see &url(https://cr.yp.to/proto/verp.txt) &--
are a way of helping mailing list administrators discover which subscription
.cindex "SMTP" "passed connection"
.cindex "SMTP" "multiple deliveries"
.cindex "multiple SMTP deliveries"
+.cindex "first pass routing"
Mail waiting to be sent from an intermittently connected host will probably
not have been routed, because without a connection DNS lookups are not
possible. This means that if a normal queue run is done at connection time,
&`DKIM`& domain verified in incoming message
&`DN `& distinguished name from peer certificate
&`DS `& DNSSEC secured lookups
-&`DT `& on &`=>`& lines: time taken for a delivery
+&`DT `& on &`=>`&, &'=='& and &'**'& lines: time taken for, or to attempt, a delivery
&`F `& sender address (on delivery lines)
&`H `& host name and IP address
&`I `& local interface used
-&`id `& message id for incoming message
+&`id `& message id (from header) for incoming message
&`K `& CHUNKING extension used
&`L `& on &`<=`& and &`=>`& lines: PIPELINING extension used
&`M8S `& 8BITMIME status for incoming message
&` arguments `& command line arguments
&`*connection_reject `& connection rejections
&`*delay_delivery `& immediate delivery delayed
-&` deliver_time `& time taken to perform delivery
+&` deliver_time `& time taken to attempt delivery
&` delivery_size `& add &`S=`&&'nnn'& to => lines
&`*dkim `& DKIM verified domain on <= lines
&` dkim_verbose `& separate full DKIM verification result line, per signature
&` incoming_port `& remote port on <= lines
&`*lost_incoming_connection `& as it says (includes timeouts)
&` millisec `& millisecond timestamps and RT,QT,DT,D times
+&`*msg_id `& on <= lines, Message-ID: header value
+&` msg_id_created `& on <= lines, Message-ID: header value when one had to be added
&` outgoing_interface `& local interface on => lines
&` outgoing_port `& add remote port to => lines
&`*queue_run `& start and end queue runs
&%millisec%&: Timestamps have a period and three decimal places of finer granularity
appended to the seconds value.
.next
+.cindex "log" "message id"
+&%msg_id%&: The value of the Message-ID: header.
+.next
+&%msg_id_created%&: The value of the Message-ID: header, when one had to be created.
+This will be either because the message is a bounce, or was submitted locally
+(submission mode) without one.
+The field identifier will have an asterix appended: &"id*="&.
+.next
.cindex "log" "outgoing interface"
.cindex "log" "local interface"
.cindex "log" "local address and port"
&%pid%&: The current process id is added to every log line, in square brackets,
immediately after the time and date.
.next
-.new
.cindex log pipelining
.cindex pipelining "logging outgoing"
&%pipelining%&: A field is added to delivery and accept
On accept lines, where PIPELINING was offered but not used by the client,
the field has a minus appended.
+
+.cindex "pipelining" "early connection"
+If Exim is built with the SUPPORT_PIPE_CONNECT build option
+accept "L" fields have a period appended if the feature was
+offered but not used, or an asterisk appended if used.
+Delivery "L" fields have an asterisk appended if used.
+
.next
.cindex "log" "queue run"
.cindex "queue runner" "logging"
.vitem &*-x*&
Match only non-frozen messages.
+
+.vitem &*-G*&&~<&'queuename'&>
+Match only messages in the given queue. Without this, the default queue is searched.
.endlist
The following options control the format of the output:
is insurance against disk crashes where the directory is lost but the files
themselves are recoverable.
-.new
The file formats may be changed, or new formats added, at any release.
Spool files are not intended as an interface to other programs
and should not be used as such.
-.wen
Some people are tempted into editing -D files in order to modify messages. You
need to be extremely careful if you do this; it is not recommended and you are
certificate.
.endlist
+Any of the above may have an extra hyphen prepended, to indicate the the
+corresponding data is untrusted.
+
Following the options there is a list of those addresses to which the message
is not to be delivered. This set of addresses is initialized from the command
line when the &%-t%& option is used and &%extract_addresses_remove_arguments%&
. ////////////////////////////////////////////////////////////////////////////
. ////////////////////////////////////////////////////////////////////////////
-.chapter "DKIM and SPF" "CHAPdkim" &&&
- "DKIM and SPF Support"
-.cindex "DKIM"
+.chapter "DKIM, SPF and DMARC" "CHAPdkim" &&&
+ "DKIM, SPF and DMARC Support"
.section "DKIM (DomainKeys Identified Mail)" SECDKIM
+.cindex "DKIM"
DKIM is a mechanism by which messages sent by some entity can be provably
linked to a domain which that entity controls. It permits reputation to
.cindex "DKIM" "signing"
For signing to be usable you must have published a DKIM record in DNS.
-Note that RFC 8301 says:
+Note that RFC 8301 (which does not cover EC keys) says:
.code
rsa-sha1 MUST NOT be used for signing or verifying.
.option dkim_domain smtp string list&!! unset
The domain(s) you want to sign with.
After expansion, this can be a list.
-Each element in turn is put into the &%$dkim_domain%& expansion variable
+Each element in turn,
+lowercased,
+is put into the &%$dkim_domain%& expansion variable
while expanding the remaining signing options.
If it is empty after expansion, DKIM signing is not done,
and no error will result even if &%dkim_strict%& is set.
openssl genrsa -out dkim_rsa.private 2048
openssl rsa -in dkim_rsa.private -out /dev/stdout -pubout -outform PEM
.endd
+The result file from the first command should be retained, and
+this option set to use it.
Take the base-64 lines from the output of the second command, concatenated,
for the DNS TXT record.
See section 3.6 of RFC6376 for the record specification.
Signers SHOULD use RSA keys of at least 2048 bits.
.endd
-Support for EC keys is being developed under
-&url(https://datatracker.ietf.org/doc/draft-ietf-dcrup-dkim-crypto/).
+EC keys for DKIM are defined by RFC 8463.
They are considerably smaller than RSA keys for equivalent protection.
As they are a recent development, users should consider dual-signing
(by setting a list of selectors, and an expansion for this option)
certtool --load_privkey=dkim_ed25519.private --pubkey_info --outder | tail -c +13 | base64
.endd
-Note that the format
-of Ed25519 keys in DNS has not yet been decided; this release supports
-both of the leading candidates at this time, a future release will
-probably drop support for whichever proposal loses.
+Exim also supports an alternate format
+of Ed25519 keys in DNS which was a candidate during development
+of the standard, but not adopted.
+A future release will probably drop that support.
.option dkim_hash smtp string&!! sha256
Can be set to any one of the supported hash methods, which are:
will be signed, and one signature added for a missing header with the
name will be appended.
-.new
.option dkim_timestamps smtp integer&!! unset
This option controls the inclusion of timestamp information in the signature.
If not set, no such information will be included.
both creation (t=) and expiry (x=) tags will be included.
RFC 6376 lists these tags as RECOMMENDED.
-.wen
.section "Verifying DKIM signatures in incoming mail" "SECDKIMVFY"
.cindex "DKIM" "verification"
-.new
Verification of DKIM signatures in SMTP incoming email is done for all
messages for which an ACL control &%dkim_disable_verify%& has not been set.
+.cindex DKIM "selecting signature algorithms"
+Individual classes of signature algorithm can be ignored by changing
+the main options &%dkim_verify_hashes%& or &%dkim_verify_keytypes%&.
+The &%dkim_verify_minimal%& option can be set to cease verification
+processing for a message once the first passing signature is found.
+
.cindex authentication "expansion item"
Performing verification sets up information used by the
-&$authresults$& expansion item.
-.wen
+&%authresults%& expansion item.
-.new The results of that verification are then made available to the
-&%acl_smtp_dkim%& ACL, &new(which can examine and modify them).
-By default, this ACL is called once for each
-syntactically(!) correct signature in the incoming message.
+For most purposes the default option settings suffice and the remainder
+of this section can be ignored.
+
+The results of verification are made available to the
+&%acl_smtp_dkim%& ACL, which can examine and modify them.
A missing ACL definition defaults to accept.
+By default, the ACL is called once for each
+syntactically(!) correct signature in the incoming message.
If any ACL call does not accept, the message is not accepted.
If a cutthrough delivery was in progress for the message, that is
summarily dropped (having wasted the transmission effort).
-To evaluate the &new(verification result) in the ACL
+To evaluate the verification result in the ACL
a large number of expansion variables
containing the signature status and its details are set up during the
runtime of the ACL.
Calling the ACL only for existing signatures is not sufficient to build
-more advanced policies. For that reason, the global option
-&%dkim_verify_signers%&, and a global expansion variable
+more advanced policies. For that reason, the main option
+&%dkim_verify_signers%&, and an expansion variable
&%$dkim_signers%& exist.
-The global option &%dkim_verify_signers%& can be set to a colon-separated
+The main option &%dkim_verify_signers%& can be set to a colon-separated
list of DKIM domains or identities for which the ACL &%acl_smtp_dkim%& is
called. It is expanded when the message has been received. At this point,
the expansion variable &%$dkim_signers%& already contains a colon-separated
If a domain or identity is listed several times in the (expanded) value of
&%dkim_verify_signers%&, the ACL is only called once for that domain or identity.
+Note that if the option is set using untrustworthy data
+(such as the From: header)
+care should be taken to force lowercase for domains
+and for the domain part if identities.
+The default setting can be regarded as trustworthy in this respect.
+
If multiple signatures match a domain (or identity), the ACL is called once
for each matching signature.
-Inside the &%acl_smtp_dkim%&, the following expansion variables are
+Inside the DKIM ACL, the following expansion variables are
available (from most to least important):
algorithms (currently, rsa-sha1) have permanently failed evaluation
.endd
-To enforce this you must have a DKIM ACL which checks this variable
-and overwrites the &$dkim_verify_status$& variable as discussed above.
+To enforce this you must either have a DKIM ACL which checks this variable
+and overwrites the &$dkim_verify_status$& variable as discussed above,
+or have set the main option &%dkim_verify_hashes%& to exclude
+processing of such signatures.
.vitem &%$dkim_canon_body%&
The body canonicalization method. One of 'relaxed' or 'simple'.
The number of signed body bytes. If zero ("0"), the body is unsigned. If no
limit was set by the signer, "9999999999999" is returned. This makes sure
that this variable always expands to an integer value.
-.new
&*Note:*& The presence of the signature tag specifying a signing body length
is one possible route to spoofing of valid DKIM signatures.
A paranoid implementation might wish to regard signature where this variable
shows less than the "no limit" return as being invalid.
-.wen
.vitem &%$dkim_created%&
UNIX timestamp reflecting the date and time when the signature was created.
SPF is a mechanism whereby a domain may assert which IP addresses may transmit
messages with its domain in the envelope from, documented by RFC 7208.
-For more information on SPF see &url(http://www.openspf.org).
-. --- 2018-09-07: still not https
+For more information on SPF see &url(http://www.open-spf.org), a static copy of
+the &url(http://openspf.org).
+. --- 2019-10-28: still not https, open-spf.org is told to be a
+. --- web-archive copy of the now dead openspf.org site
+. --- See https://www.mail-archive.com/mailop@mailop.org/msg08019.html for a
+. --- discussion.
Messages sent by a system not authorised will fail checking of such assertions.
This includes retransmissions done by traditional forwarders.
For verification, an ACL condition and an expansion lookup are provided.
.cindex authentication "expansion item"
Performing verification sets up information used by the
-&$authresults$& expansion item.
+&%authresults%& expansion item.
.cindex SPF "ACL condition"
message = $sender_host_address is not allowed to send mail from \
${if def:sender_address_domain \
{$sender_address_domain}{$sender_helo_name}}. \
- Please see http://www.openspf.org/Why?scope=\
+ Please see http://www.open-spf.org/Why?scope=\
${if def:sender_address_domain {mfrom}{helo}};\
identity=${if def:sender_address_domain \
{$sender_address}{$sender_helo_name}};\
"Best-guess". Strictly speaking, "Best-guess" is not standard
SPF, but it is supported by the same framework that enables SPF
capability.
-Refer to &url(http://www.openspf.org/FAQ/Best_guess_record)
+Refer to &url(http://www.open-spf.org/FAQ/Best_guess_record)
for a description of what it means.
-. --- 2018-09-07: still not https:
+. --- 2019-10-28: still not https:
To access this feature, simply use the spf_guess condition in place
of the spf one. For example:
.cindex SPF "lookup expansion"
.cindex lookup spf
A lookup expansion is also available. It takes an email
-address as the key and an IP address as the database:
+address as the key and an IP address
+(v4 or v6)
+as the database:
.code
${lookup {username@domain} spf {ip.ip.ip.ip}}
The lookup will return the same result strings as can appear in
&$spf_result$& (pass,fail,softfail,neutral,none,err_perm,err_temp).
-Currently, only IPv4 addresses are supported.
+
+
+
+
+
+.section DMARC SECDMARC
+.cindex DMARC verification
+
+DMARC combines feedback from SPF, DKIM, and header From: in order
+to attempt to provide better indicators of the authenticity of an
+email. This document does not explain the fundamentals; you
+should read and understand how it works by visiting the website at
+&url(http://www.dmarc.org/).
+
+If Exim is built with DMARC support,
+the libopendmarc library is used.
+
+For building Exim yourself, obtain the library from
+&url(http://sourceforge.net/projects/opendmarc/)
+to obtain a copy, or find it in your favorite package
+repository. You will need to attend to the local/Makefile feature
+SUPPORT_DMARC and the associated LDFLAGS addition.
+This description assumes
+that headers will be in /usr/local/include, and that the libraries
+are in /usr/local/lib.
+
+. subsection
+
+There are three main-configuration options:
+.cindex DMARC "configuration options"
+
+The &%dmarc_tld_file%& option
+.oindex &%dmarc_tld_file%&
+defines the location of a text file of valid
+top level domains the opendmarc library uses
+during domain parsing. Maintained by Mozilla,
+the most current version can be downloaded
+from a link at &url(https://publicsuffix.org/list/public_suffix_list.dat).
+See also the util/renew-opendmarc-tlds.sh script.
+.new
+The default for the option is unset.
+If not set, DMARC processing is disabled.
+.wen
+
+
+The &%dmarc_history_file%& option, if set
+.oindex &%dmarc_history_file%&
+defines the location of a file to log results
+of dmarc verification on inbound emails. The
+contents are importable by the opendmarc tools
+which will manage the data, send out DMARC
+reports, and expire the data. Make sure the
+directory of this file is writable by the user
+exim runs as.
+The default is unset.
+
+The &%dmarc_forensic_sender%& option
+.oindex &%dmarc_forensic_sender%&
+defines an alternate email address to use when sending a
+forensic report detailing alignment failures
+if a sender domain's dmarc record specifies it
+and you have configured Exim to send them.
+If set, this is expanded and used for the
+From: header line; the address is extracted
+from it and used for the envelope from.
+If not set (the default), the From: header is expanded from
+the dsn_from option, and <> is used for the
+envelope from.
+
+. I wish we had subsections...
+
+.cindex DMARC controls
+By default, the DMARC processing will run for any remote,
+non-authenticated user. It makes sense to only verify DMARC
+status of messages coming from remote, untrusted sources. You can
+use standard conditions such as hosts, senders, etc, to decide that
+DMARC verification should *not* be performed for them and disable
+DMARC with an ACL control modifier:
+.code
+ control = dmarc_disable_verify
+.endd
+A DMARC record can also specify a "forensic address", which gives
+exim an email address to submit reports about failed alignment.
+Exim does not do this by default because in certain conditions it
+results in unintended information leakage (what lists a user might
+be subscribed to, etc). You must configure exim to submit forensic
+reports to the owner of the domain. If the DMARC record contains a
+forensic address and you specify the control statement below, then
+exim will send these forensic emails. It is also advised that you
+configure a &%dmarc_forensic_sender%& because the default sender address
+construction might be inadequate.
+.code
+ control = dmarc_enable_forensic
+.endd
+(AGAIN: You can choose not to send these forensic reports by simply
+not putting the dmarc_enable_forensic control line at any point in
+your exim config. If you don't tell exim to send them, it will not
+send them.)
+
+There are no options to either control. Both must appear before
+the DATA acl.
+
+. subsection
+
+DMARC checks cam be run on incoming SMTP messages by using the
+&"dmarc_status"& ACL condition in the DATA ACL. You are required to
+call the &"spf"& condition first in the ACLs, then the &"dmarc_status"&
+condition. Putting this condition in the ACLs is required in order
+for a DMARC check to actually occur. All of the variables are set
+up before the DATA ACL, but there is no actual DMARC check that
+occurs until a &"dmarc_status"& condition is encountered in the ACLs.
+
+The &"dmarc_status"& condition takes a list of strings on its
+right-hand side. These strings describe recommended action based
+on the DMARC check. To understand what the policy recommendations
+mean, refer to the DMARC website above. Valid strings are:
+.display
+&'accept '& The DMARC check passed and the library recommends accepting the email.
+&'reject '& The DMARC check failed and the library recommends rejecting the email.
+&'quarantine '& The DMARC check failed and the library recommends keeping it for further inspection.
+&'none '& The DMARC check passed and the library recommends no specific action, neutral.
+&'norecord '& No policy section in the DMARC record for this sender domain.
+&'nofrom '& Unable to determine the domain of the sender.
+&'temperror '& Library error or dns error.
+&'off '& The DMARC check was disabled for this email.
+.endd
+You can prefix each string with an exclamation mark to invert its
+meaning, for example "!accept" will match all results but
+"accept". The string list is evaluated left-to-right in a
+short-circuit fashion. When a string matches the outcome of the
+DMARC check, the condition succeeds. If none of the listed
+strings matches the outcome of the DMARC check, the condition
+fails.
+
+Of course, you can also use any other lookup method that Exim
+supports, including LDAP, Postgres, MySQL, etc, as long as the
+result is a list of colon-separated strings.
+
+Performing the check sets up information used by the
+&%authresults%& expansion item.
+
+Several expansion variables are set before the DATA ACL is
+processed, and you can use them in this ACL. The following
+expansion variables are available:
+
+.vlist
+.vitem &$dmarc_status$&
+.vindex &$dmarc_status$&
+.cindex DMARC result
+A one word status indicating what the DMARC library
+thinks of the email. It is a combination of the results of
+DMARC record lookup and the SPF/DKIM/DMARC processing results
+(if a DMARC record was found). The actual policy declared
+in the DMARC record is in a separate expansion variable.
+
+.vitem &$dmarc_status_text$&
+.vindex &$dmarc_status_text$&
+Slightly longer, human readable status.
+
+.vitem &$dmarc_used_domain$&
+.vindex &$dmarc_used_domain$&
+The domain which DMARC used to look up the DMARC policy record.
+
+.vitem &$dmarc_domain_policy$&
+.vindex &$dmarc_domain_policy$&
+The policy declared in the DMARC record. Valid values
+are "none", "reject" and "quarantine". It is blank when there
+is any error, including no DMARC record.
+.endlist
+
+. subsection
+
+By default, Exim's DMARC configuration is intended to be
+non-intrusive and conservative. To facilitate this, Exim will not
+create any type of logging files without explicit configuration by
+you, the admin. Nor will Exim send out any emails/reports about
+DMARC issues without explicit configuration by you, the admin (other
+than typical bounce messages that may come about due to ACL
+processing or failure delivery issues).
+
+In order to log statistics suitable to be imported by the opendmarc
+tools, you need to:
+.ilist
+Configure the global option &%dmarc_history_file%&
+.next
+Configure cron jobs to call the appropriate opendmarc history
+import scripts and truncating the dmarc_history_file
+.endlist
+
+In order to send forensic reports, you need to:
+.ilist
+Configure the global option &%dmarc_forensic_sender%&
+.next
+Configure, somewhere before the DATA ACL, the control option to
+enable sending DMARC forensic reports
+.endlist
+
+. subsection
+
+Example usage:
+.code
+(RCPT ACL)
+ warn domains = +local_domains
+ hosts = +local_hosts
+ control = dmarc_disable_verify
+
+ warn !domains = +screwed_up_dmarc_records
+ control = dmarc_enable_forensic
+
+ warn condition = (lookup if destined to mailing list)
+ set acl_m_mailing_list = 1
+
+(DATA ACL)
+ warn dmarc_status = accept : none : off
+ !authenticated = *
+ log_message = DMARC DEBUG: $dmarc_status $dmarc_used_domain
+
+ warn dmarc_status = !accept
+ !authenticated = *
+ log_message = DMARC DEBUG: '$dmarc_status' for $dmarc_used_domain
+
+ warn dmarc_status = quarantine
+ !authenticated = *
+ set $acl_m_quarantine = 1
+ # Do something in a transport with this flag variable
+
+ deny condition = ${if eq{$dmarc_domain_policy}{reject}}
+ condition = ${if eq{$acl_m_mailing_list}{1}}
+ message = Messages from $dmarc_used_domain break mailing lists
+
+ deny dmarc_status = reject
+ !authenticated = *
+ message = Message from $dmarc_used_domain failed sender's DMARC policy, REJECT
+
+ warn add_header = :at_start:${authresults {$primary_hostname}}
+.endd
+
.endd
If &$proxy_session$& is set but &$proxy_external_address$& is empty
there was a protocol error.
+The variables &$sender_host_address$& and &$sender_host_port$&
+will have values for the actual client system, not the proxy.
Since the real connections are all coming from the proxy, and the
per host connection tracking is done before Proxy Protocol is
If mua_wrapper is set, the utf8_downconvert control
is initially set to -1.
-.new
The smtp transport has an option &%utf8_downconvert%&.
If set it must expand to one of the three values described above,
and it overrides any previously set value.
-.wen
There is no explicit support for VRFY and EXPN.
The name is placed in the variable &$event_name$& and the event action
expansion must check this, as it will be called for every possible event type.
+.new
The current list of events is:
+.wen
.display
&`dane:fail after transport `& per connection
&`msg:complete after main `& per message
+&`msg:defer after transport `& per message per delivery try
&`msg:delivery after transport `& per recipient
&`msg:rcpt:host:defer after transport `& per recipient per host
&`msg:rcpt:defer after transport `& per recipient
-&`msg:host:defer after transport `& per attempt
+&`msg:host:defer after transport `& per host per delivery try; host errors
&`msg:fail:delivery after transport `& per recipient
&`msg:fail:internal after main `& per recipient
&`tcp:connect before transport `& per connection
&`tcp:close after transport `& per connection
&`tls:cert before both `& per certificate in verification chain
&`smtp:connect after transport `& per connection
+&`smtp:ehlo after transport `& per connection
.endd
New event types may be added in future.
with the event type:
.display
&`dane:fail `& failure reason
+&`msg:defer `& error string
&`msg:delivery `& smtp confirmation message
&`msg:fail:internal `& failure reason
&`msg:fail:delivery `& smtp error message
+&`msg:host:defer `& error string
&`msg:rcpt:host:defer `& error string
&`msg:rcpt:defer `& error string
-&`msg:host:defer `& error string
&`tls:cert `& verification chain depth
&`smtp:connect `& smtp banner
+&`smtp:ehlo `& smtp ehlo response
.endd
The :defer events populate one extra variable: &$event_defer_errno$&.
git://git.exim.org / users / jgh / exim.git / blobdiff