-$Cambridge: exim/doc/doc-txt/ChangeLog,v 1.294 2006/02/13 12:02:59 ph10 Exp $
+$Cambridge: exim/doc/doc-txt/ChangeLog,v 1.319 2006/03/01 11:40:51 ph10 Exp $
Change log file for Exim from version 4.21
-------------------------------------------
PH/26 Added the /no_tell option to "control=freeze".
+PH/27 If a host name lookup failed very early in a connection, for example, if
+ the IP address matched host_lookup and the reverse lookup yielded a name
+ that did not have a forward lookup, an error message of the form "no IP
+ address found for host xxx.xxx.xxx (during SMTP connection from NULL)"
+ could be logged. Now it outputs the IP address instead of "NULL".
+
+PH/28 An enabling patch from MH: add new function child_open_exim2() which
+ allows the sender and the authenticated sender to be set when
+ submitting a message from within Exim. Since child_open_exim() is
+ documented for local_scan(), the new function should be too.
+
+PH/29 In GnuTLS, a forced expansion failure for tls_privatekey was not being
+ ignored. In both GnuTLS and OpenSSL, an expansion of tls_privatekey that
+ results in an empty string is now treated as unset.
+
+PH/30 Fix eximon buffer overflow bug (Bugzilla #73).
+
+PH/31 Added sender_verify_fail logging option.
+
+PH/32 In November 2003, the code in Exim that added an empty Bcc: header when
+ needed by RFC 822 but not by RFC 2822 was commented out. I have now
+ tidied the source and removed it altogether.
+
+PH/33 When a queue run was abandoned because the load average was too high, a
+ log line was always written; now it is written only if the queue_run log
+ selector is set. In addition, the log line for abandonment now contains
+ information about the queue run such as the pid. This is always present
+ in "start" and "stop" lines but was omitted from the "abandon" line.
+
+PH/34 Omit spaces between a header name and the colon in the error message that
+ is given when verify = headers_syntax fails (if there are lots of them,
+ the message gets confusing).
+
+PH/35 Change the default for dns_check_names_pattern to allow slashes within
+ names, as there are now some PTR records that contain slashes. This check
+ is only to protect against broken name servers that fall over on strange
+ characters, so the fact that it applies to all lookups doesn't matter.
+
+PH/36 Now that the new test suite is complete, we can remove some of the
+ special code in Exim that was needed for the old test suite. For example,
+ sorting DNS records because real resolvers return them in an arbitrary
+ order. The new test suite's fake resolver always returns records in the
+ same order.
+
+PH/37 When running in the test harness, use -odi for submitted messages (e.g.
+ bounces) except when queue_only is set, to avoid logging races between
+ the different processes.
+
+PH/38 Panic-die if .include specifies a non-absolute path.
+
+PH/39 A tweak to the "H" retry rule from its user.
+
+JJ/03 exipick: Removed parentheses from 'next' and 'last' calls that specified
+ a label. They prevented compilation on older perls.
+
+JJ/04 exipick: Refactored code to prevent implicit split to @_ which caused
+ a warning to be raised on newish perls.
+
+JJ/05 exipick: Fixed bug where -bpc always showed a count of all messages
+ on queue. Changes to match documented behaviour of showing count of
+ messages matching specified criteria.
+
+PH/40 Changed the default ident timeout from 30s to 5s.
+
+PH/41 Added support for the use of login_cap features, on those BSD systems
+ that have them, for controlling the resources used by pipe deliveries.
+
+PH/42 The content-scanning code uses fopen() to create files in which to put
+ message data. Previously it was not paying any attention to the mode of
+ the files. Exim runs with umask(0) because the rest of the code creates
+ files with open(), and sets the required mode explicitly. Thus, these
+ files were ending up world-writeable. This was not a big issue, because,
+ being within the spool directory, they were not world-accessible. I have
+ created a function called modefopen, which takes an additional mode
+ argument. It sets umask(777), creates the file, chmods it to the required
+ mode, then resets the umask. All the relevant calls to fopen() in the
+ content scanning code have been changed to use this function.
+
+PH/43 If retry_interval_max is set greater than 24 hours, it is quietly reset
+ to 24 hours. This avoids potential overflow problems when processing G
+ and H retry rules. I suspect nobody ever tinkers with this value.
+
+PH/44 Added STRIP_COMMAND=/usr/bin/strip to the FreeBSD Makefile.
+
+PH/45 When the plaintext authenticator is running as a client, the server's
+ challenges are checked to ensure they are valid base64 strings. By
+ default, the authentication attempt is cancelled if an invalid string is
+ received. Setting client_ignore_invalid_base64 true ignores these errors.
+ The decoded challenge strings are now placed in $auth1, $auth2, etc. as
+ they are received. Thus, the responses can be made to depend on the
+ challenges. If an invalid string is ignored, an empty string is placed in
+ the variable.
+
+PH/46 Messages that are created by the autoreply transport now contains a
+ References: header, in accordance with RFCs 2822 and 3834.
+
+PH/47 Added authenticated_sender_force to the smtp transport.
+
+PH/48 The ${prvs expansion was broken on systems where time_t was long long.
+
+PH/49 Installed latest patch from the Sieve maintainer.
+
+PH/50 When an Exim quota was set without a file count quota, and mailbox_size
+ was also set, the appendfile transport was unnecessarily scanning a
+ directory of message files (e.g. for maildir delivery) to find the count
+ of files (along with the size), even though it did not need this
+ information. It now does the scan only if it needs to find either the
+ size of the count of files.
+
+PH/51 Added ${time_eval: to convert Exim time strings into seconds.
Exim version 4.60
git://git.exim.org / users / jgh / exim.git / blobdiff