+ 9. When an address is delayed because of a 4xx response to a RCPT command, it
+ is now the combination of sender and recipient that is delayed in
+ subsequent queue runs until its retry time is reached. You can revert to
+ the previous behavious, that is, delay the recipient independent of the
+ sender, by setting address_retry_include_sender=false in the smtp
+ transport. However, this can lead to problems with servers that regularly
+ issue 4xx responses to RCPT commands.
+
+10. Unary negation and the bitwise logical operators and, or, xor, not, and
+ shift, have been added to the eval: and eval10: expansion items. These
+ items may now contain arithmetic operators (plus, minus, times, divide,
+ remainder, negate), bitwise operators (and, or, xor, not, shift), and
+ parentheses. All operations are carried out using signed integer
+ arithmetic. Operator priorities are as in C, namely:
+
+ (highest) not, negate
+ times, divide, remainder
+ plus, minus
+ shift-left, shift-right
+ and
+ xor
+ (lowest) or
+
+ Binary operators with the same priority are evaluated from left to right.
+ For example:
+
+ ${eval:1+1} yields 2
+ ${eval:1+2*3} yields 7
+ ${eval:(1+2)*3} yields 9
+ ${eval:2+42%5} yields 4
+ ${eval:0xc&5} yields 4
+ ${eval:0xc|5} yields 13
+ ${eval:0xc^5} yields 9
+ ${eval:0xc>>1} yields 6
+ ${eval:0xc<<1} yields 24
+ ${eval:~255&0x1234} yields 4608
+ ${eval:-(~255&0x1234)} yields -4608
+
+11. The variables $interface_address and $interface_port have been renamed
+ as $received_ip_address and $received_port, to make it clear that they
+ relate to message reception rather than delivery. (The old names remain
+ available for compatibility.)
+
+12. The "message" modifier can now be used on acl verbs to vary the message
+ that is sent when an SMTP command is accepted. For example, in a RCPT ACL
+ you could have:
+
+ accept <some conditions>
+ message = OK, I'll allow you through today
+
+ Previously, this message modifier would have had no effect whatsoever.
+
+ IMPORTANT: The new behaviour applies to "accept" (and "discard") only if
+ there is no occurrence of "endpass" in the statement. If "endpass" is
+ present, the behaviour reverts to the old case, where "message" applies to
+ rejection. This is for backwards compatibility.
+
+ It is always possible to rewrite ACL statements so that "endpass" is not
+ needed (and indeed it is no longer used in the default configuration, and
+ is somewhat not recommended nowadays because it causes confusion.)
+
+ It is now generally true that the "message" modifier sets up a text string
+ that is expanded and used as a response message if the current statement
+ terminates the ACL. The expansion happens at the time Exim decides that the
+ ACL is to end, not at the time it processes "message". If the expansion
+ fails, or generates an empty string, the modifier is ignored.
+
+ For ACLs that are triggered by SMTP commands, the message is returned as
+ part of the SMTP response. In this situation, the message may begin with an
+ overriding SMTP response code, optionally followed by an "extended response
+ code". However, the first digit of the supplied response code must be the
+ same as would be sent by default. A panic occurs if it is not. For the
+ predata ACL, note that the default success code is 354, not 2xx.
+
+ However, notwithstanding the previous paragraph, for the QUIT ACL, unlike
+ the others, the message modifier cannot override the 221 response code.
+
+ In the case of the "connect" ACL, accepting with a message modifier
+ overrides the value of smtp_banner.
+
+ The ACL test specified by acl_smtp_helo happens when the client issues the
+ HELO or EHLO commands, after the tests specified by helo_accept_junk_hosts,
+ helo_allow_chars and helo(_try)_verify_hosts. An acceptance message
+ modifier for EHLO/HELO may not contain more than one line (it will be
+ truncated at the first newline and a panic logged), and it cannot affect
+ the EHLO options.
+
+
+
+Version 4.63
+------------
+
+1. There is a new Boolean option called filter_prepend_home for the redirect
+ router.
+
+2. There is a new acl, set by acl_not_smtp_start, which is run right at the
+ start of receiving a non-SMTP message, before any of the message has been
+ read.
+
+3. When an SMTP error message is specified in a "message" modifier in an ACL,
+ or in a :fail: or :defer: message in a redirect router, Exim now checks the
+ start of the message for an SMTP error code.
+
+4. There is a new parameter for LDAP lookups called "referrals", which takes
+ one of the settings "follow" (the default) or "nofollow".
+
+5. Version 20070721.2 of exipick now included, offering these new options:
+ --reverse
+ After all other sorting options have bee processed, reverse order
+ before displaying messages (-R is synonym).
+ --random
+ Randomize order of matching messages before displaying.
+ --size
+ Instead of displaying the matching messages, display the sum
+ of their sizes.
+ --sort <variable>[,<variable>...]
+ Before displaying matching messages, sort the messages according to
+ each messages value for each variable.
+ --not
+ Negate the value for every test (returns inverse output from the
+ same criteria without --not).
+
+
+Version 4.62
+------------
+
+1. The ${readsocket expansion item now supports Internet domain sockets as well
+ as Unix domain sockets. If the first argument begins "inet:", it must be of
+ the form "inet:host:port". The port is mandatory; it may be a number or the
+ name of a TCP port in /etc/services. The host may be a name, or it may be an
+ IP address. An ip address may optionally be enclosed in square brackets.
+ This is best for IPv6 addresses. For example:
+
+ ${readsocket{inet:[::1]:1234}{<request data>}...
+
+ Only a single host name may be given, but if looking it up yield more than
+ one IP address, they are each tried in turn until a connection is made. Once
+ a connection has been made, the behaviour is as for ${readsocket with a Unix
+ domain socket.
+
+2. If a redirect router sets up file or pipe deliveries for more than one
+ incoming address, and the relevant transport has batch_max set greater than
+ one, a batch delivery now occurs.
+
+3. The appendfile transport has a new option called maildirfolder_create_regex.
+ Its value is a regular expression. For a maildir delivery, this is matched
+ against the maildir directory; if it matches, Exim ensures that a
+ maildirfolder file is created alongside the new, cur, and tmp directories.
+
+
+Version 4.61
git://git.exim.org / users / jgh / exim.git / blobdiff