configure a dmarc_forensic_sender because the default sender address
construction might be inadequate.
- control = dmarc_forensic_enable
+ control = dmarc_enable_forensic
(AGAIN: You can choose not to send these forensic reports by simply
-not putting the dmarc_forensic_enable control line at any point in
+not putting the dmarc_enable_forensic control line at any point in
your exim config. If you don't tell it to send them, it will not
send them.)
deny dmarc_status = reject
!authenticated = *
- message = Message from $domain_used_domain failed sender's DMARC policy, REJECT
+ message = Message from $dmarc_used_domain failed sender's DMARC policy, REJECT
+SOCKS
+------------------------------------------------------------
+Support for proxying outbound SMTP via a Socks 5 proxy
+(RFC 1928) is included if Exim is compiled with
+EXPERIMENTAL_SOCKS defined.
+
+If an smtp transport has a nonempty socks_proxy option
+defined, this is active. The option is expanded and
+should be a list (colon-separated by default) of
+proxy specifiers. Each proxy specifier is a list
+(space-separated by default) where the initial element
+is an IP address and any subsequent elements are options.
+
+Options are a string <name>=<value>.
+These options are currently defined:
+- "auth", with possible values "none" and "name".
+ Using "name" selects username/password authentication
+ per RFC 1929. Default is "none".
+- "name" sets the authentication username. Default is empty.
+- "pass" sets the authentication password. Default is empty.
+- "port" sets the tcp port number for the proxy. Default is 1080.
+- "tmo" sets a connection timeout in seconds for this proxy. Default is 5.
+
+Proxies from the list are tried in order until
+one responds. The timeout for the overall connection
+applies to the set of proxied attempts.
+
+If events are used, the remote IP/port during a
+tcp:connect event will be that of the proxy.
+
+
+
+
DANE
------------------------------------------------------------
DNS-based Authentication of Named Entities, as applied
$tls_out_tlsa_usage (detailed above).
+
+SMTPUTF8
+------------------------------------------------------------
+Internationalised mail name handling.
+RFCs 6530, 6533, 5890
+
+Compile with EXPERIMENTAL_INTERNATIONAL and libidn.
+
+New main config option smtputf8_advertise_hosts, default '*',
+a host list. If this matches the sending host and
+accept_8bitmime is true (the default) then the ESMTP option
+SMTPUTF8 will be advertised.
+
+If the sender specifies the SMTPUTF8 option on a MAIL command
+international handling for the message is enabled and
+the expansion variable $message_smtputf8 will have value TRUE.
+
+The option allow_utf8_domains is set to true for this
+message. All DNS lookups are converted to a-label form
+whatever the setting of allow_utf8_domains.
+
+Both localparts and domain are maintained as the original
+utf8 form internally; any matching or regex use will
+require appropriate care. Filenames created, eg. by
+the appendfile transport, will have utf8 name.
+
+Helo names sent by the smtp transport will have any utf8
+components expanded to a-label form.
+
+Log lines and Received-by: header lines will aquire a "utf8"
+prefix on the protocol element, eg. utf8esmtp.
+
+New expansion operators:
+ ${utf8_domain_to_alabel:str}
+ ${utf8_domain_from_alabel:str}
+ ${utf8_localpart_to_alabel:str}
+ ${utf8_localpart_from_alabel:str}
+
+New "control = utf8_downconvert" ACL modifier,
+sets a flag requiring that addresses are converted to
+a-label form before smtp delivery, for use in a
+Message Submission Agent context. Can also be
+phrased as "control = utf8_downconvert/1" and is
+mandatory. The flag defaults to zero and can be cleared
+by "control = utf8_downconvert/0". The value "-1"
+may also be used, to use a-label for only if the
+destination host does not support SMTPUTF8.
+
+If mua_wrapper is set, the utf8_downconvert control
+defaults to -1 (convert if needed).
+
+
+There is no explicit support for VRFY and EXPN.
+Configurations supporting these should inspect
+$smtp_command_argument for an SMTPUTF8 argument.
+
+There is no support for LMTP on Unix sockets.
+Using the "lmtp" protocol option on an smtp transport,
+for LMTP over TCP, should work as expected.
+
+Known issues:
+ - DSN unitext handling is not present
+ - no provision for converting logging from or to UTF-8
+
--------------------------------------------------------------
End of file
--------------------------------------------------------------
git://git.exim.org / users / jgh / exim.git / blobdiff