configure a dmarc_forensic_sender because the default sender address
construction might be inadequate.
- control = dmarc_forensic_enable
+ control = dmarc_enable_forensic
(AGAIN: You can choose not to send these forensic reports by simply
-not putting the dmarc_forensic_enable control line at any point in
+not putting the dmarc_enable_forensic control line at any point in
your exim config. If you don't tell it to send them, it will not
send them.)
deny dmarc_status = reject
!authenticated = *
- message = Message from $domain_used_domain failed sender's DMARC policy, REJECT
+ message = Message from $dmarc_used_domain failed sender's DMARC policy, REJECT
+SOCKS
+------------------------------------------------------------
+Support for proxying outbound SMTP via a Socks 5 proxy
+(RFC 1928) is included if Exim is compiled with
+EXPERIMENTAL_SOCKS defined.
+
+If an smtp transport has a nonempty socks_proxy option
+defined, this is active. The option is expanded and
+should be a list (colon-separated by default) of
+proxy specifiers. Each proxy specifier is a list
+(space-separated by default) where the initial element
+is an IP address and any subsequent elements are options.
+
+Options are a string <name>=<value>.
+These options are currently defined:
+- "auth", with possible values "none" and "name".
+ Using "name" selects username/password authentication
+ per RFC 1929. Default is "none".
+- "name" sets the authentication username. Default is empty.
+- "pass" sets the authentication password. Default is empty.
+- "port" sets the tcp port number for the proxy. Default is 1080.
+- "tmo" sets a connection timeout in seconds for this proxy. Default is 5.
+
+Proxies from the list are tried in order until
+one responds. The timeout for the overall connection
+applies to the set of proxied attempts.
+
+If events are used, the remote IP/port during a
+tcp:connect event will be that of the proxy.
+
+
+
+
DANE
------------------------------------------------------------
DNS-based Authentication of Named Entities, as applied
$tls_out_tlsa_usage (detailed above).
+
+INTERNATIONAL
+------------------------------------------------------------
+SMTPUTF8
+Internationalised mail name handling.
+RFCs 6530, 6533, 5890
+
+Compile with EXPERIMENTAL_INTERNATIONAL and libidn.
+
+New main config option smtputf8_advertise_hosts, default '*',
+a host list. If this matches the sending host and
+accept_8bitmime is true (the default) then the ESMTP option
+SMTPUTF8 will be advertised.
+
+If the sender specifies the SMTPUTF8 option on a MAIL command
+international handling for the message is enabled and
+the expansion variable $message_smtputf8 will have value TRUE.
+
+The option allow_utf8_domains is set to true for this
+message. All DNS lookups are converted to a-label form
+whatever the setting of allow_utf8_domains.
+
+Both localparts and domain are maintained as the original
+utf8 form internally; any matching or regex use will
+require appropriate care. Filenames created, eg. by
+the appendfile transport, will have utf8 name.
+
+Helo names sent by the smtp transport will have any utf8
+components expanded to a-label form.
+
+Any certificate name checks will be done using the a-label
+form of the name.
+
+Log lines and Received-by: header lines will aquire a "utf8"
+prefix on the protocol element, eg. utf8esmtp.
+
+New expansion operators:
+ ${utf8_domain_to_alabel:str}
+ ${utf8_domain_from_alabel:str}
+ ${utf8_localpart_to_alabel:str}
+ ${utf8_localpart_from_alabel:str}
+
+New "control = utf8_downconvert" ACL modifier,
+sets a flag requiring that addresses are converted to
+a-label form before smtp delivery, for use in a
+Message Submission Agent context. Can also be
+phrased as "control = utf8_downconvert/1" and is
+mandatory. The flag defaults to zero and can be cleared
+by "control = utf8_downconvert/0". The value "-1"
+may also be used, to use a-label for only if the
+destination host does not support SMTPUTF8.
+
+If mua_wrapper is set, the utf8_downconvert control
+defaults to -1 (convert if needed).
+
+
+There is no explicit support for VRFY and EXPN.
+Configurations supporting these should inspect
+$smtp_command_argument for an SMTPUTF8 argument.
+
+There is no support for LMTP on Unix sockets.
+Using the "lmtp" protocol option on an smtp transport,
+for LMTP over TCP, should work as expected.
+
+Known issues:
+ - DSN unitext handling is not present
+ - no provision for converting logging from or to UTF-8
+
+----
+IMAP folder names
+
+New expansion operator:
+
+${imapfolder {<string>} {<sep>} {<specials>}}
+
+The string is converted from the charset specified by the headers charset
+command (in a filter file) or headers_charset global option, to the
+modified UTF-7 encoding specified by RFC 2060, with the following
+exception: All occurences of <sep> (which has to be a single character)
+are replaced with periods ("."), and all periods and slashes that aren't
+<sep> and are not in the <specials> string are BASE64 encoded.
+
+The third argument can be omitted, defaulting to an empty string.
+The second argument can be omitted, defaulting to "/".
+
+This is the encoding used by Courier for Maildir names on disk, and followed
+by many other IMAP servers.
+
+ Example 1: ${imapfolder {Foo/Bar}} yields "Foo.Bar".
+ Example 2: ${imapfolder {Foo/Bar}{.}{/}} yields "Foo&AC8-Bar".
+ Example 3: ${imapfolder {Räksmörgås}} yields "R&AOQ-ksm&APY-rg&AOU-s".
+
+Note that the source charset setting is vital, and also that characters
+must be representable in UTF-16.
+
+
+
+
--------------------------------------------------------------
End of file
--------------------------------------------------------------
git://git.exim.org / users / jgh / exim.git / blobdiff