UTF8: mua_wrapper

[users/jgh/exim.git] / test / README

diff --git a/test/README b/test/README
index 80c35117b4de9f0605df5de522563a19cfa3954a..d971bc7441bca055069f2890b4b48cf9a523482b 100644 (file)
--- a/test/README
+++ b/test/README
@@ -116,6 +116,9 @@ In order to run this test suite, the following requirements must be met:
 
 (9) Exim must be built with TRUSTED_CONFIG_LIST support, so that the test
     configs can be placed into it.  A suitable file location is .../exim/test/trusted_configs
 
 (9) Exim must be built with TRUSTED_CONFIG_LIST support, so that the test
     configs can be placed into it.  A suitable file location is .../exim/test/trusted_configs

+    with content .../exim/test/test-config [fill out the ... to make full
+    paths].  This file should be owner/group matching CONFIGURE_OWNER/GROUP,
+    or root/root.  The config files in .../exim/test/confs/ should be owner/group the same.

     DISABLE_D_OPTION must not be used. If ALT_CONFIG_PREFIX is used, it
     must contain the directory of the test-suite.  WHITELIST_D_MACROS should contain:
     
     DISABLE_D_OPTION must not be used. If ALT_CONFIG_PREFIX is used, it
     must contain the directory of the test-suite.  WHITELIST_D_MACROS should contain:
     


@@ -897,13 +900,15 @@ input, details of which are given below. A number of options are implemented:
 
   -d       causes the server to output debugging information
 
 
   -d       causes the server to output debugging information
 

-  -t       sets a timeout in seconds (default 5) for when the server is
+  -t <sec> sets a timeout (default 5) for when the server is

            awaiting an incoming connection
 
   -noipv4  causes the server not to set up an IPv4 socket
 
   -noipv6  causes the server not to set up an IPv6 socket
 
            awaiting an incoming connection
 
   -noipv4  causes the server not to set up an IPv4 socket
 
   -noipv6  causes the server not to set up an IPv6 socket
 

+  -i <sec> sets an initial pause, to delay before creating the listen sockets
+

 By default, in an IPv6 environment, both kinds of socket are set up. However,
 the test script knows which interfaces actually exist on the host, and it adds
 -noipv4 or -noipv6 to the server command as required. An error occurs if both
 By default, in an IPv6 environment, both kinds of socket are set up. However,
 the test script knows which interfaces actually exist on the host, and it adds
 -noipv4 or -noipv6 to the server command as required. An error occurs if both


@@ -1019,7 +1024,10 @@ are of the following kinds:
     (d) If the line starts with ">*eof", nothing is sent and the connection
           is closed.
 
     (d) If the line starts with ">*eof", nothing is sent and the connection
           is closed.
 

-    The data that is sent starts after the initial '>' sequence.
+    The data that is sent starts after the initial '>' sequence.  Within
+    each line the sequence '\x' followed by two hex digits can be used
+    to specify an arbitrary byte value.  The sequence '\\' specifies a
+    single backslash.

 
 (2) A line that starts with "*sleep" specifies a number of seconds to wait
     before proceeding.
 
 (2) A line that starts with "*sleep" specifies a number of seconds to wait
     before proceeding.


@@ -1033,7 +1041,10 @@ are of the following kinds:
 (5) Otherwise, the line defines the start of an input line that the client
     is expected to send. To allow for lines that start with digits, the line
     may start with '<', which is not taken as part of the input data. If the
 (5) Otherwise, the line defines the start of an input line that the client
     is expected to send. To allow for lines that start with digits, the line
     may start with '<', which is not taken as part of the input data. If the

-    input does not match, the server bombs out with an error message.
+    lines starts with '<<' then only the characters are expected; no return-
+    linefeed terminator. If the input does not match, the server bombs out
+    with an error message.  Backslash-escape sequences may be used in the
+    line content as for output lines.

 
 Here is a simple example of server use in a test script:
 
 
 Here is a simple example of server use in a test script: