-$Cambridge: exim/doc/doc-txt/NewStuff,v 1.53 2005/06/27 14:34:33 ph10 Exp $
+$Cambridge: exim/doc/doc-txt/NewStuff,v 1.64 2005/08/22 14:01:37 ph10 Exp $
New Features in Exim
--------------------
updated when there is a relatively large batch of changes). The doc/ChangeLog
file contains a listing of all changes, including bug fixes.
+Exim version 4.53
+-----------------
+
+TK/01 Added the "success_on_redirect" address verification option. When an
+ address generates new addresses during routing, Exim will abort
+ verification with "success" when more than one address has been
+ generated, but continue to verify a single new address. The latter
+ does not happen when the new "success_on_redirect" option is set, like
+
+ require verify = recipient/success_on_redirect/callout=10s
+
+ In that case, verification will succeed when a router generates a new
+ address.
+
+PH/01 Support for SQLite database lookups has been added. This is another
+ query-style lookup, but it is slightly different from the others because
+ a file name is required in addition to the SQL query. This is because an
+ SQLite database is a single file and there is no daemon as in other SQL
+ databases. The interface to Exim requires the name of the file, as an
+ absolute path, to be given at the start of the query. It is separated
+ from the query by white space. This means that the path name cannot
+ contain white space. Here is a lookup expansion example:
+
+ ${lookup sqlite {/some/thing/sqlitedb \
+ select name from aliases where id='ph10';}}
+
+ In a list, the syntax is similar. For example:
+
+ domainlist relay_domains = sqlite;/some/thing/sqlitedb \
+ select * from relays where ip='$sender_host_address';
+
+ The only character affected by the ${quote_sqlite: operator is a single
+ quote, which it doubles.
+
+ The SQLite library handles multiple simultaneous accesses to the database
+ internally. Multiple readers are permitted, but only one process can
+ update at once. Attempts to access the database while it is being updated
+ are rejected after a timeout period, during which the SQLite library
+ waits for the lock to be released. In Exim, the default timeout is set
+ to 5 seconds, but it can be changed by means of the sqlite_lock_timeout
+ option.
+
+ Note that you must set LOOKUP_SQLITE=yes in Local/Makefile in order to
+ obtain SQLite support, and you will also need to add -lsqlite3 to the
+ EXTRALIBS setting. And of course, you have to install SQLite on your
+ host first.
+
+PH/02 The variable $message_id is now deprecated, to be replaced by
+ $message_exim_id, which makes it clearer which ID is being referenced.
+
+PH/03 The use of forbid_filter_existstest now also locks out the use of the
+ ${stat: expansion item.
+
+PH/04 The IGNOREQUOTA extension to the LMTP protocol is now available in both
+ the lmtp transport and the smtp transport running in LMTP mode. In the
+ lmtp transport there is a new Boolean option called ignore_quota, and in
+ the smtp transport there is a new Boolean option called
+ lmtp_ignore_quota. If either of these options is set TRUE, the string
+ "IGNOREQUOTA" is added to RCPT commands when using the LMTP protocol,
+ provided that the server has advertised support for IGNOREQUOTA in its
+ response to the LHLO command.
+
+PH/05 Previously, if "verify = helo" was set in an ACL, the condition was true
+ only if the host matched helo_try_verify_hosts, which caused the
+ verification to occur when the EHLO/HELO command was issued. The ACL just
+ tested the remembered result. Now, if a previous verification attempt has
+ not happened, "verify = helo" does it there and then.
+
+PH/06 It is now possible to specify a port number along with a host name or
+ IP address in the list of hosts defined in the manualroute or
+ queryprogram routers, fallback_hosts, or the "hosts" option of the smtp
+ transport. These all override any port specification on the transport.
+ The relatively standard syntax of using a colon separator has been
+ adopted, but there are some gotchas that need attention:
+
+ * In all these lists of hosts, colon is the default separator, so either
+ the colon that specifies a port must be doubled, or the separator must
+ be changed. The following two examples have the same effect:
+
+ fallback_hosts = host1.tld::1225 : host2.tld::1226
+ fallback_hosts = <; host1.tld:1225 ; host2.tld:1226
+
+ * When IPv6 addresses are involved, it gets worse, because they contain
+ colons of their own. To make this case easier, it is permitted to
+ enclose an IP address (either v4 or v6) in square brackets if a port
+ number follows. Here's an example from a manualroute router:
+
+ route_list = * "</ [10.1.1.1]:1225 / [::1]:1226"
+
+ If the "/MX" feature is to be used as well as a port specifier, the port
+ must come last. For example:
+
+ route_list = * dom1.tld/mx::1225
+
+PH/07 $smtp_command_argument is now set for all SMTP commands, not just the
+ non-message ones. This makes it possible to inspect the complete command
+ for RCPT commands, for example.
+
Exim version 4.52
-----------------
example, you can limit the sending rate of each authenticated user,
independent of the computer they are sending from, by setting the key
to $authenticated_id. The default key is $sender_host_address.
+ Internally, Exim includes the smoothing constant p and the options in
+ the lookup key because they alter the meaning of the stored data.
+ This is not true for the limit m, so you can alter the configured
+ maximum rate and Exim will still remember clients' past behaviour,
+ but if you alter the other ratelimit parameters Exim will effectively
+ forget their past behaviour.
Each ratelimit condition can have up to two options. The first option
specifies what Exim measures the rate of, and the second specifies how
cdb {DB/ratelimits.cdb} \
{$value} {RATELIMIT} }
+ Warning: if you have a busy server with a lot of ratelimit tests,
+ especially with the per_rcpt option, you may suffer from a performance
+ bottleneck caused by locking on the ratelimit hints database. Apart from
+ making your ACLs less complicated, you can reduce the problem by using a
+ RAM disk for Exim's hints directory, /var/spool/exim/db/. However this
+ means that Exim will lose its hints data after a reboot (including retry
+ hints, the callout cache, and ratelimit data).
+
TK/01 Added an 'spf' lookup type that will return an SPF result for a given
email address (the key) and an IP address (the database):
git://git.exim.org / users / jgh / exim.git / blobdiff