+
+DCC Support
+--------------------------------------------------------------
+Distributed Checksum Clearinghouse; http://www.rhyolite.com/dcc/
+
+*) Building exim
+
+In order to build exim with DCC support add
+
+EXPERIMENTAL_DCC=yes
+
+to your Makefile. (Re-)build/install exim. exim -d should show
+EXPERIMENTAL_DCC under "Support for".
+
+
+*) Configuration
+
+In the main section of exim.cf add at least
+ dccifd_address = /usr/local/dcc/var/dccifd
+or
+ dccifd_address = <ip> <port>
+
+In the DATA ACL you can use the new condition
+ dcc = *
+
+After that "$dcc_header" contains the X-DCC-Header.
+
+Return values are:
+ fail for overall "R", "G" from dccifd
+ defer for overall "T" from dccifd
+ accept for overall "A", "S" from dccifd
+
+dcc = */defer_ok works as for spamd.
+
+The "$dcc_result" variable contains the overall result from DCC
+answer. There will an X-DCC: header added to the mail.
+
+Usually you'll use
+ defer !dcc = *
+to greylist with DCC.
+
+If you set, in the main section,
+ dcc_direct_add_header = true
+then the dcc header will be added "in deep" and if the spool
+file was already written it gets removed. This forces Exim to
+write it again if needed. This helps to get the DCC Header
+through to eg. SpamAssassin.
+
+If you want to pass even more headers in the middle of the
+DATA stage you can set
+ $acl_m_dcc_add_header
+to tell the DCC routines to add more information; eg, you might set
+this to some results from ClamAV. Be careful. Header syntax is
+not checked and is added "as is".
+
+In case you've troubles with sites sending the same queue items from several
+hosts and fail to get through greylisting you can use
+$acl_m_dcc_override_client_ip
+
+Setting $acl_m_dcc_override_client_ip to an IP address overrides the default
+of $sender_host_address. eg. use the following ACL in DATA stage:
+
+ warn set acl_m_dcc_override_client_ip = \
+ ${lookup{$sender_helo_name}nwildlsearch{/etc/mail/multipleip_sites}{$value}{}}
+ condition = ${if def:acl_m_dcc_override_client_ip}
+ log_message = dbg: acl_m_dcc_override_client_ip set to \
+ $acl_m_dcc_override_client_ip
+
+Then set something like
+# cat /etc/mail/multipleip_sites
+mout-xforward.gmx.net 82.165.159.12
+mout.gmx.net 212.227.15.16
+
+Use a reasonable IP. eg. one the sending cluster actually uses.
+
+
+
+DMARC Support
+--------------------------------------------------------------
+
+DMARC combines feedback from SPF, DKIM, and header From: in order
+to attempt to provide better indicators of the authenticity of an
+email. This document does not explain the fundamentals, you
+should read and understand how it works by visiting the website at
+http://www.dmarc.org/.
+
+DMARC support is added via the libopendmarc library. Visit:
+
+ http://sourceforge.net/projects/opendmarc/
+
+to obtain a copy, or find it in your favorite rpm package
+repository. If building from source, this description assumes
+that headers will be in /usr/local/include, and that the libraries
+are in /usr/local/lib.
+
+1. To compile Exim with DMARC support, you must first enable SPF.
+Please read the Local/Makefile comments on enabling the SUPPORT_SPF
+feature. You must also have DKIM support, so you cannot set the
+DISABLE_DKIM feature. Once both of those conditions have been met
+you can enable DMARC in Local/Makefile:
+
+EXPERIMENTAL_DMARC=yes
+LDFLAGS += -lopendmarc
+# CFLAGS += -I/usr/local/include
+# LDFLAGS += -L/usr/local/lib
+
+The first line sets the feature to include the correct code, and
+the second line says to link the libopendmarc libraries into the
+exim binary. The commented out lines should be uncommented if you
+built opendmarc from source and installed in the default location.
+Adjust the paths if you installed them elsewhere, but you do not
+need to uncomment them if an rpm (or you) installed them in the
+package controlled locations (/usr/include and /usr/lib).
+
+
+2. Use the following global settings to configure DMARC:
+
+Required:
+dmarc_tld_file Defines the location of a text file of valid
+ top level domains the opendmarc library uses
+ during domain parsing. Maintained by Mozilla,
+ the most current version can be downloaded
+ from a link at http://publicsuffix.org/list/.
+
+Optional:
+dmarc_history_file Defines the location of a file to log results
+ of dmarc verification on inbound emails. The
+ contents are importable by the opendmarc tools
+ which will manage the data, send out DMARC
+ reports, and expire the data. Make sure the
+ directory of this file is writable by the user
+ exim runs as.
+
+dmarc_forensic_sender The email address to use when sending a
+ forensic report detailing alignment failures
+ if a sender domain's dmarc record specifies it
+ and you have configured Exim to send them.
+ Default: do-not-reply@$default_hostname
+
+
+3. By default, the DMARC processing will run for any remote,
+non-authenticated user. It makes sense to only verify DMARC
+status of messages coming from remote, untrusted sources. You can
+use standard conditions such as hosts, senders, etc, to decide that
+DMARC verification should *not* be performed for them and disable
+DMARC with a control setting:
+
+ control = dmarc_disable_verify
+
+A DMARC record can also specify a "forensic address", which gives
+exim an email address to submit reports about failed alignment.
+Exim does not do this by default because in certain conditions it
+results in unintended information leakage (what lists a user might
+be subscribed to, etc). You must configure exim to submit forensic
+reports to the owner of the domain. If the DMARC record contains a
+forensic address and you specify the control statement below, then
+exim will send these forensic emails. It's also advised that you
+configure a dmarc_forensic_sender because the default sender address
+construction might be inadequate.
+
+ control = dmarc_enable_forensic
+
+(AGAIN: You can choose not to send these forensic reports by simply
+not putting the dmarc_enable_forensic control line at any point in
+your exim config. If you don't tell it to send them, it will not
+send them.)
+
+There are no options to either control. Both must appear before
+the DATA acl.
+
+
+4. You can now run DMARC checks in incoming SMTP by using the
+"dmarc_status" ACL condition in the DATA ACL. You are required to
+call the spf condition first in the ACLs, then the "dmarc_status"
+condition. Putting this condition in the ACLs is required in order
+for a DMARC check to actually occur. All of the variables are set
+up before the DATA ACL, but there is no actual DMARC check that
+occurs until a "dmarc_status" condition is encountered in the ACLs.
+
+The dmarc_status condition takes a list of strings on its
+right-hand side. These strings describe recommended action based
+on the DMARC check. To understand what the policy recommendations
+mean, refer to the DMARC website above. Valid strings are:
+
+ o accept The DMARC check passed and the library recommends
+ accepting the email.
+ o reject The DMARC check failed and the library recommends
+ rejecting the email.
+ o quarantine The DMARC check failed and the library recommends
+ keeping it for further inspection.
+ o none The DMARC check passed and the library recommends
+ no specific action, neutral.
+ o norecord No policy section in the DMARC record for this
+ sender domain.
+ o nofrom Unable to determine the domain of the sender.
+ o temperror Library error or dns error.
+ o off The DMARC check was disabled for this email.
+
+You can prefix each string with an exclamation mark to invert its
+meaning, for example "!accept" will match all results but
+"accept". The string list is evaluated left-to-right in a
+short-circuit fashion. When a string matches the outcome of the
+DMARC check, the condition succeeds. If none of the listed
+strings matches the outcome of the DMARC check, the condition
+fails.
+
+Of course, you can also use any other lookup method that Exim
+supports, including LDAP, Postgres, MySQL, etc, as long as the
+result is a list of colon-separated strings.
+
+Several expansion variables are set before the DATA ACL is
+processed, and you can use them in this ACL. The following
+expansion variables are available:
+
+ o $dmarc_status
+ This is a one word status indicating what the DMARC library
+ thinks of the email. It is a combination of the results of
+ DMARC record lookup and the SPF/DKIM/DMARC processing results
+ (if a DMARC record was found). The actual policy declared
+ in the DMARC record is in a separate expansion variable.
+
+ o $dmarc_status_text
+ This is a slightly longer, human readable status.
+
+ o $dmarc_used_domain
+ This is the domain which DMARC used to look up the DMARC
+ policy record.
+
+ o $dmarc_domain_policy
+ This is the policy declared in the DMARC record. Valid values
+ are "none", "reject" and "quarantine". It is blank when there
+ is any error, including no DMARC record.
+
+A now-redundant variable $dmarc_ar_header has now been withdrawn.
+Use the ${authresults } expansion instead.
+
+
+5. How to enable DMARC advanced operation:
+By default, Exim's DMARC configuration is intended to be
+non-intrusive and conservative. To facilitate this, Exim will not
+create any type of logging files without explicit configuration by
+you, the admin. Nor will Exim send out any emails/reports about
+DMARC issues without explicit configuration by you, the admin (other
+than typical bounce messages that may come about due to ACL
+processing or failure delivery issues).
+
+In order to log statistics suitable to be imported by the opendmarc
+tools, you need to:
+a. Configure the global setting dmarc_history_file.
+b. Configure cron jobs to call the appropriate opendmarc history
+ import scripts and truncating the dmarc_history_file.
+
+In order to send forensic reports, you need to:
+a. Configure the global setting dmarc_forensic_sender.
+b. Configure, somewhere before the DATA ACL, the control option to
+ enable sending DMARC forensic reports.
+
+
+6. Example usage:
+(RCPT ACL)
+ warn domains = +local_domains
+ hosts = +local_hosts
+ control = dmarc_disable_verify
+
+ warn !domains = +screwed_up_dmarc_records
+ control = dmarc_enable_forensic
+
+ warn condition = (lookup if destined to mailing list)
+ set acl_m_mailing_list = 1
+
+(DATA ACL)
+ warn dmarc_status = accept : none : off
+ !authenticated = *
+ log_message = DMARC DEBUG: $dmarc_status $dmarc_used_domain
+ add_header = $dmarc_ar_header
+
+ warn dmarc_status = !accept
+ !authenticated = *
+ log_message = DMARC DEBUG: '$dmarc_status' for $dmarc_used_domain
+
+ warn dmarc_status = quarantine
+ !authenticated = *
+ set $acl_m_quarantine = 1
+ # Do something in a transport with this flag variable
+
+ deny condition = ${if eq{$dmarc_domain_policy}{reject}}
+ condition = ${if eq{$acl_m_mailing_list}{1}}
+ message = Messages from $dmarc_used_domain break mailing lists
+
+ deny dmarc_status = reject
+ !authenticated = *
+ message = Message from $dmarc_used_domain failed sender's DMARC policy, REJECT
+
+
+
+DSN extra information
+---------------------
+If compiled with EXPERIMENTAL_DSN_INFO extra information will be added
+to DSN fail messages ("bounces"), when available. The intent is to aid
+tracing of specific failing messages, when presented with a "bounce"
+complaint and needing to search logs.
+
+
+The remote MTA IP address, with port number if nonstandard.
+Example:
+ Remote-MTA: X-ip; [127.0.0.1]:587
+Rationale:
+ Several addresses may correspond to the (already available)
+ dns name for the remote MTA.
+
+The remote MTA connect-time greeting.
+Example:
+ X-Remote-MTA-smtp-greeting: X-str; 220 the.local.host.name ESMTP Exim x.yz Tue, 2 Mar 1999 09:44:33 +0000
+Rationale:
+ This string sometimes presents the remote MTA's idea of its
+ own name, and sometimes identifies the MTA software.
+
+The remote MTA response to HELO or EHLO.
+Example:
+ X-Remote-MTA-helo-response: X-str; 250-the.local.host.name Hello localhost [127.0.0.1]
+Limitations:
+ Only the first line of a multiline response is recorded.
+Rationale:
+ This string sometimes presents the remote MTA's view of
+ the peer IP connecting to it.
+
+The reporting MTA detailed diagnostic.
+Example:
+ X-Exim-Diagnostic: X-str; SMTP error from remote mail server after RCPT TO:<d3@myhost.test.ex>: 550 hard error
+Rationale:
+ This string sometimes give extra information over the
+ existing (already available) Diagnostic-Code field.
+
+
+Note that non-RFC-documented field names and data types are used.
+
+
+LMDB Lookup support
+-------------------
+LMDB is an ultra-fast, ultra-compact, crash-proof key-value embedded data store.
+It is modeled loosely on the BerkeleyDB API. You should read about the feature
+set as well as operation modes at https://symas.com/products/lightning-memory-mapped-database/
+
+LMDB single key lookup support is provided by linking to the LMDB C library.
+The current implementation does not support writing to the LMDB database.
+
+Visit https://github.com/LMDB/lmdb to download the library or find it in your
+operating systems package repository.
+
+If building from source, this description assumes that headers will be in
+/usr/local/include, and that the libraries are in /usr/local/lib.
+
+1. In order to build exim with LMDB lookup support add or uncomment
+
+EXPERIMENTAL_LMDB=yes
+
+to your Local/Makefile. (Re-)build/install exim. exim -d should show
+Experimental_LMDB in the line "Support for:".
+
+EXPERIMENTAL_LMDB=yes
+LDFLAGS += -llmdb
+# CFLAGS += -I/usr/local/include
+# LDFLAGS += -L/usr/local/lib
+
+The first line sets the feature to include the correct code, and
+the second line says to link the LMDB libraries into the
+exim binary. The commented out lines should be uncommented if you
+built LMDB from source and installed in the default location.
+Adjust the paths if you installed them elsewhere, but you do not
+need to uncomment them if an rpm (or you) installed them in the
+package controlled locations (/usr/include and /usr/lib).
+
+2. Create your LMDB files, you can use the mdb_load utility which is
+part of the LMDB distribution our your favourite language bindings.
+
+3. Add the single key lookups to your exim.conf file, example lookups
+are below.
+
+${lookup{$sender_address_domain}lmdb{/var/lib/baruwa/data/db/relaydomains.mdb}{$value}}
+${lookup{$sender_address_domain}lmdb{/var/lib/baruwa/data/db/relaydomains.mdb}{$value}fail}
+${lookup{$sender_address_domain}lmdb{/var/lib/baruwa/data/db/relaydomains.mdb}}
+
+
+Queuefile transport
+-------------------
+Queuefile is a pseudo transport which does not perform final delivery.
+It simply copies the exim spool files out of the spool directory into
+an external directory retaining the exim spool format.
+
+The spool files can then be processed by external processes and then
+requeued into exim spool directories for final delivery.
+
+The motivation/inspiration for the transport is to allow external
+processes to access email queued by exim and have access to all the
+information which would not be available if the messages were delivered
+to the process in the standard email formats.
+
+The mailscanner package is one of the processes that can take advantage
+of this transport to filter email.
+
+The transport can be used in the same way as the other existing transports,
+i.e by configuring a router to route mail to a transport configured with
+the queuefile driver.
+
+The transport only takes one option:
+
+* directory - This is used to specify the directory messages should be
+copied to
+
+The generic transport options (body_only, current_directory, disable_logging,
+debug_print, delivery_date_add, envelope_to_add, event_action, group,
+headers_add, headers_only, headers_remove, headers_rewrite, home_directory,
+initgroups, max_parallel, message_size_limit, rcpt_include_affixes,
+retry_use_local_part, return_path, return_path_add, shadow_condition,
+shadow_transport, transport_filter, transport_filter_timeout, user) are
+ignored.
+
+Sample configuration:
+
+(Router)
+
+scan:
+ driver = accept
+ transport = scan
+
+(Transport)
+
+scan:
+ driver = queuefile
+ directory = /var/spool/baruwa-scanner/input
+
+
+In order to build exim with Queuefile transport support add or uncomment
+
+EXPERIMENTAL_QUEUEFILE=yes
+
+to your Local/Makefile. (Re-)build/install exim. exim -d should show
+Experimental_QUEUEFILE in the line "Support for:".
+
+
+ARC support
+-----------
+Specification: https://tools.ietf.org/html/draft-ietf-dmarc-arc-protocol-11
+Note that this is not an RFC yet, so may change.
+
+ARC is intended to support the utility of SPF and DKIM in the presence of
+intermediaries in the transmission path - forwarders and mailinglists -
+by establishing a cryptographically-signed chain in headers.
+
+Normally one would only bother doing ARC-signing when functioning as
+an intermediary. One might do verify for local destinations.
+
+ARC uses the notion of a "ADministrative Management Domain" (ADMD).
+Described in RFC 5598 (section 2.3), this is essentially the set of
+mail-handling systems that the mail transits. A label should be chosen to
+identify the ADMD. Messages should be ARC-verified on entry to the ADMD,
+and ARC-signed on exit from it.
+
+
+Verification
+--
+An ACL condition is provided to perform the "verifier actions" detailed
+in section 6 of the above specification. It may be called from the DATA ACL
+and succeeds if the result matches any of a given list.
+It also records the highest ARC instance number (the chain size)
+and verification result for later use in creating an Authentication-Results:
+standard header.
+
+ verify = arc/<acceptable_list> none:fail:pass
+
+ add_header = :at_start:${authresults {<admd-identifier>}}
+
+ Note that it would be wise to strip incoming messages of A-R headers
+ that claim to be from our own <admd-identifier>.
+
+There are two new variables: $arc_state and $arc_state_reason.
+
+Receive log lines for an ARC pass will be tagged "ARC".
+
+
+Signing
+--
+arc_sign = <admd-identifier> : <selector> : <privkey>
+An option on the smtp transport, which constructs and prepends to the message
+an ARC set of headers. The textually-first Authentication-Results: header
+is used as a basis (you must have added one on entry to the ADMD).
+Expanded; if unset, empty or forced-failure then no signing is done.
+
+
+