-# $Cambridge: exim/src/src/EDITME,v 1.22 2008/07/25 20:23:25 fanf2 Exp $
+# $Cambridge: exim/src/src/EDITME,v 1.27 2010/06/12 15:21:25 jetmore Exp $
##################################################
# The Exim mail transport agent #
# group that is used for Exim processes when they no longer need to be root. In
# particular, this applies when receiving messages and when doing remote
# deliveries. (Local deliveries run as various non-root users, typically as the
-# owner of a local mailbox.) Specifying these values as root is very strongly
-# discouraged.
+# owner of a local mailbox.) Specifying these values as root is not supported.
EXIM_USER=
# SUPPORT_MBX=yes
+#------------------------------------------------------------------------------
+# See below for dynamic lookup modules.
+# LOOKUP_MODULE_DIR=/usr/lib/exim/lookups/
+# If not using package management but using this anyway, then think about how
+# you perform upgrades and revert them. You should consider the benefit of
+# embedding the Exim version number into LOOKUP_MODULE_DIR, so that you can
+# maintain two concurrent sets of modules.
+
+# To build a module dynamically, you'll need to define CFLAGS_DYNAMIC for
+# your platform. Eg:
+# CFLAGS_DYNAMIC=-shared -rdynamic
+# CFLAGS_DYNAMIC=-shared -rdynamic -fPIC
+
#------------------------------------------------------------------------------
# These settings determine which file and database lookup methods are included
# in the binary. See the manual chapter entitled "File and database lookups"
# LOOKUP_DNSDB does *not* refer to general mail routing using the DNS. It is
# for the specialist case of using the DNS as a general database facility (not
# common).
+# If set to "2" instead of "yes" then the corresponding lookup will be
+# built as a module and must be installed into LOOKUP_MODULE_DIR. You need to
+# add -export-dynamic -rdynamic to EXTRALIBS. You may also need to add -ldl to
+# EXTRALIBS so that dlopen() is available to Exim. You need to define
+# LOOKUP_MODULE_DIR above so the exim binary actually loads dynamic lookup
+# modules.
+# Also, instead of adding all the libraries/includes to LOOKUP_INCLUDE and
+# LOOKUP_LIBS, add them to the respective LOOKUP_*_INCLUDE and LOOKUP_*_LIBS
+# (where * is the name as given here in this list). That ensures that only
+# the dynamic library and not the exim binary will be linked against the
+# library.
+# NOTE: LDAP cannot be built as a module!
LOOKUP_DBM=yes
LOOKUP_LSEARCH=yes
+LOOKUP_DNSDB=yes
# LOOKUP_CDB=yes
-# LOOKUP_DNSDB=yes
# LOOKUP_DSEARCH=yes
# LOOKUP_IBASE=yes
# LOOKUP_LDAP=yes
# WITH_OLD_DEMIME=yes
+# If you're using ClamAV and are backporting fixes to an old version, instead
+# of staying current (which is the more usual approach) then you may need to
+# use an older API which uses a STREAM command, now deprecated, instead of
+# zINSTREAM. If you need to set this, please let the Exim developers know, as
+# if nobody reports a need for it, we'll remove this option and clean up the
+# code. zINSTREAM was introduced with ClamAV 0.95.
+#
+# WITH_OLD_CLAMAV_STREAM=yes
+
+#------------------------------------------------------------------------------
+# By default Exim includes code to support DKIM (DomainKeys Identified
+# Mail, RFC4871) signing and verification. Verification of signatures is
+# turned on by default. See the spec for information on conditionally
+# disabling it. To disable the inclusion of the entire feature, set
+# DISABLE_DKIM to "yes"
+
+# DISABLE_DKIM=yes
+
+
#------------------------------------------------------------------------------
# Compiling Exim with experimental features. These are documented in
# experimental-spec.txt. "Experimental" means that the way these features are
#------------------------------------------------------------------------------
-# By default, Exim insists that its configuration file be owned either by root
-# or by the Exim user. You can specify one additional permitted owner here.
+# By default, Exim insists that its configuration file be owned by root. You
+# can specify one additional permitted owner here.
# CONFIGURE_OWNER=
# If the configuration file is group-writeable, Exim insists by default that it
-# is owned by root or the Exim user. You can specify one additional permitted
-# group owner here.
+# is owned by root. You can specify one additional permitted group owner here.
# CONFIGURE_GROUP=
#------------------------------------------------------------------------------
# The -C option allows Exim to be run with an alternate runtime configuration
-# file. When this is used by root or the Exim user, root privilege is retained
-# by the binary (for any other caller, it is dropped). You can restrict the
-# location of alternate configurations by defining a prefix below. Any file
-# used with -C must then start with this prefix (except that /dev/null is also
-# permitted if the caller is root, because that is used in the install script).
-# If the prefix specifies a directory that is owned by root, a compromise of
-# the Exim account does not permit arbitrary alternate configurations to be
-# used. The prefix can be more restrictive than just a directory (the second
-# example).
+# file. When this is used by root, root privilege is retained by the binary
+# (for any other caller including the Exim user, it is dropped). You can
+# restrict the location of alternate configurations by defining a prefix below.
+# Any file used with -C must then start with this prefix (except that /dev/null
+# is also permitted if the caller is root, because that is used in the install
+# script). If the prefix specifies a directory that is owned by root, a
+# compromise of the Exim account does not permit arbitrary alternate
+# configurations to be used. The prefix can be more restrictive than just a
+# directory (the second example).
# ALT_CONFIG_PREFIX=/some/directory/
# ALT_CONFIG_PREFIX=/some/directory/exim.conf-
#------------------------------------------------------------------------------
-# If you uncomment the following line, only root may use the -C or -D options
-# without losing root privilege. The -C option specifies an alternate runtime
-# configuration file, and the -D option changes macro values in the runtime
-# configuration. Uncommenting this line restricts what can be done with these
-# options. A call to receive a message (either one-off or via a daemon) cannot
-# successfully continue to deliver it, because the re-exec of Exim to regain
-# root privilege will fail, owing to the use of -C or -D by the Exim user.
-# However, you can still use -C for testing (as root) if you do separate Exim
-# calls for receiving a message and subsequently delivering it.
+# When a user other than root uses the -C option to override the configuration
+# file (including the Exim user when re-executing Exim to regain root
+# privileges for local message delivery), this will normally cause Exim to
+# drop root privileges. The TRUSTED_CONFIG_LIST option, specifies a file which
+# contains a list of trusted configuration filenames, one per line. If the -C
+# option is used by the Exim user or by the user specified in the
+# CONFIGURE_OWNER setting, to specify a configuration file which is listed in
+# the TRUSTED_CONFIG_LIST file, then root privileges are not dropped by Exim.
-# ALT_CONFIG_ROOT_ONLY=yes
+# TRUSTED_CONFIG_LIST=/usr/exim/trusted_configs
#------------------------------------------------------------------------------
# DISABLE_D_OPTION=yes
+#------------------------------------------------------------------------------
+# By contrast, you might be maintaining a system which relies upon the ability
+# to override values with -D and assumes that these will be passed through to
+# the delivery processes. As of Exim 4.73, this is no longer the case by
+# default. Going forward, we strongly recommend that you use a shim Exim
+# configuration file owned by root stored under TRUSTED_CONFIG_LIST.
+# That shim can set macros before .include'ing your main configuration file.
+#
+# As a strictly transient measure to ease migration to 4.73, the
+# WHITELIST_D_MACROS value definies a colon-separated list of macro-names
+# which are permitted to be overriden from the command-line which will be
+# honoured by the Exim user. So these are macros that can persist to delivery
+# time.
+# Examples might be -DTLS or -DSPOOL=/some/dir. The values on the
+# command-line are filtered to only permit: [A-Za-z0-9_/.-]*
+#
+# This option is highly likely to be removed in a future release. It exists
+# only to make 4.73 as easy as possible to migrate to. If you use it, we
+# encourage you to schedule time to rework your configuration to not depend
+# upon it. Most people should not need to use this.
+#
+# By default, no macros are whitelisted for -D usage.
+
+# WHITELIST_D_MACROS=TLS:SPOOL
+
#------------------------------------------------------------------------------
# Exim has support for the AUTH (authentication) extension of the SMTP
# protocol, as defined by RFC 2554. If you don't know what SMTP authentication
#
# but of course there may need to be other things in CFLAGS and EXTRALIBS_EXIM
# as well.
+#
+# To use a name other than exim in the tcpwrappers config file,
+# e.g. if you're running multiple daemons with different access lists,
+# or multiple MTAs with the same access list, define
+# TCP_WRAPPERS_DAEMON_NAME accordingly
+#
+# TCP_WRAPPERS_DAEMON_NAME="exim"
#------------------------------------------------------------------------------
git://git.exim.org / users / heiko / exim.git / blobdiff