Fix docs, `dns_dnssec_ok` not `dns_use_dnssec`

[users/heiko/exim.git] / doc / doc-docbook / spec.xfpt

diff --git a/doc/doc-docbook/spec.xfpt b/doc/doc-docbook/spec.xfpt
index 88308ba238c4eb1bb27f9cacd71103e5c8aa15a7..ece837d03f77bbefafef5d906f9129a8e4687171 100644 (file)
--- a/doc/doc-docbook/spec.xfpt
+++ b/doc/doc-docbook/spec.xfpt
@@ -52,7 +52,7 @@
 .set I   "    "
 
 .macro copyyear
-2013
+2014
 .endmacro
 
 . /////////////////////////////////////////////////////////////////////////////
@@ -11978,7 +11978,7 @@ other times, this variable is false.
 It is likely that you will need to coerce DNSSEC support on in the resolver
 library, by setting:
 .code
-dns_use_dnssec = 1
+dns_dnssec_ok = 1
 .endd
 
 Exim does not perform DNSSEC validation itself, instead leaving that to a
@@ -13190,10 +13190,10 @@ See also the &'Policy controls'& section above.
 .row &%disable_ipv6%&                "do no IPv6 processing"
 .row &%dns_again_means_nonexist%&    "for broken domains"
 .row &%dns_check_names_pattern%&     "pre-DNS syntax check"
+.row &%dns_dnssec_ok%&               "parameter for resolver"
 .row &%dns_ipv4_lookup%&             "only v4 lookup for these domains"
 .row &%dns_retrans%&                 "parameter for resolver"
 .row &%dns_retry%&                   "parameter for resolver"
-.row &%dns_use_dnssec%&              "parameter for resolver"
 .row &%dns_use_edns0%&               "parameter for resolver"
 .row &%hold_domains%&                "hold delivery for these domains"
 .row &%local_interfaces%&            "for routing checks"
@@ -13814,6 +13814,17 @@ This option controls whether or not an IP address, given as a CSA domain, is
 reversed and looked up in the reverse DNS, as described in more detail in
 section &<<SECTverifyCSA>>&.
 
+
+.option dns_dnssec_ok main integer -1
+.cindex "DNS" "resolver options"
+.cindex "DNS" "DNSSEC"
+If this option is set to a non-negative number then Exim will initialise the
+DNS resolver library to either use or not use DNSSEC, overriding the system
+default. A value of 0 coerces DNSSEC off, a value of 1 coerces DNSSEC on.
+
+If the resolver library does not support DNSSEC then this option has no effect.
+
+
 .option dns_ipv4_lookup main "domain list&!!" unset
 .cindex "IPv6" "DNS lookup for AAAA records"
 .cindex "DNS" "IPv6 lookup for AAAA records"
@@ -13844,16 +13855,6 @@ to set in them.
 See &%dns_retrans%& above.
 
 
-.option dns_use_dnssec main integer -1
-.cindex "DNS" "resolver options"
-.cindex "DNS" "DNSSEC"
-If this option is set to a non-negative number then Exim will initialise the
-DNS resolver library to either use or not use DNSSEC, overriding the system
-default. A value of 0 coerces DNSSEC off, a value of 1 coerces DNSSEC on.
-
-If the resolver library does not support DNSSEC then this option has no effect.
-
-
 .option dns_use_edns0 main integer -1
 .cindex "DNS" "resolver options"
 .cindex "DNS" "EDNS0"
@@ -27295,6 +27296,9 @@ after the ACL completes.
 
 Note that routers are used in verify mode.  Note also that headers cannot be
 modified by any of the post-data ACLs (DATA, MIME and DKIM).
+Cutthrough delivery is not supported via transport-filters or when DKIM signing
+of outgoing messages is done, because it sends data to the ultimate destination
+before the entire message has been received from the source.
 
 Should the ultimate destination system positively accept or reject the mail,
 a corresponding indication is given to the source system and nothing is queued.
@@ -27305,7 +27309,6 @@ line.
 
 Delivery in this mode avoids the generation of a bounce mail to a (possibly faked)
 sender when the destination system is doing content-scan based rejection.
-Cutthrough delivery is not supported via transport-filters.
 
 
 .vitem &*control&~=&~debug/*&<&'options'&>
@@ -36347,7 +36350,9 @@ disabled by setting DISABLE_DKIM=yes in Local/Makefile.
 Exim's DKIM implementation allows to
 .olist
 Sign outgoing messages: This function is implemented in the SMTP transport.
-It can co-exist with all other Exim features, including transport filters.
+It can co-exist with all other Exim features
+(including transport filters)
+except cutthrough delivery.
 .next
 Verify signatures in incoming messages: This is implemented by an additional
 ACL (acl_smtp_dkim), which can be called several times per message, with
@@ -36438,6 +36443,10 @@ used.
 Verification of DKIM signatures in incoming email is implemented via the
 &%acl_smtp_dkim%& ACL. By default, this ACL is called once for each
 syntactically(!) correct signature in the incoming message.
+A missing ACL definition defaults to accept.
+If any ACL call does not acccept, the message is not accepted.
+If a cutthrough delivery was in progress for the message it is
+summarily dropped (having wasted the transmission effort).
 
 To evaluate the signature in the ACL a large number of expansion variables
 containing the signature status and its details are set up during the