Add perl_taintmode option

[users/heiko/exim.git] / doc / doc-docbook / spec.xfpt

diff --git a/doc/doc-docbook/spec.xfpt b/doc/doc-docbook/spec.xfpt
index cb913d6f1f481e5566f6f812173b17e447430636..8a0c96753d6aaeb957c759e46012a069e1aad516 100644 (file)
--- a/doc/doc-docbook/spec.xfpt
+++ b/doc/doc-docbook/spec.xfpt
@@ -9677,7 +9677,8 @@ ${readsocket{inet:[::1]:1234}{request string}}
 Only a single host name may be given, but if looking it up yields more than
 one IP address, they are each tried in turn until a connection is made. For
 both kinds of socket, Exim makes a connection, writes the request string
-(unless it is an empty string) and reads from the socket until an end-of-file
+unless it is an empty string; and no terminating NUL is ever sent)
+and reads from the socket until an end-of-file
 is read. A timeout of 5 seconds is applied. Additional, optional arguments
 extend what can be done. Firstly, you can vary the timeout. For example:
 .code
@@ -12966,6 +12967,14 @@ overriding the setting of &%perl_at_start%&.
 There is also a command line option &%-pd%& (for delay) which suppresses the
 initial startup, even if &%perl_at_start%& is set.
 
+.ilist
+.oindex "&%perl_taintmode%&"
+To provide more security executing Perl code via the embedded Perl
+interpeter, the &%perl_taintmode%& option can be set. This enables the
+taint mode of the Perl interpreter. You are encouraged to set this
+option to a true value. To avoid breaking existing installations, it
+defaults to false.
+
 
 .section "Calling Perl subroutines" "SECID86"
 When the configuration file includes a &%perl_startup%& option you can make use
@@ -13494,6 +13503,7 @@ listed in more than one group.
 .table2
 .row &%perl_at_start%&               "always start the interpreter"
 .row &%perl_startup%&                "code to obey when starting Perl"
+.row &%perl_taintmode%&                     "enable taint mode in Perl"
 .endtable
 
 
@@ -13786,6 +13796,7 @@ See also the &'Policy controls'& section above.
 .row &%bounce_message_file%&         "content of bounce"
 .row &%bounce_message_text%&         "content of bounce"
 .row &%bounce_return_body%&          "include body if returning message"
+.row &%bounce_return_linesize_limit%& "limit on returned message line length"
 .row &%bounce_return_message%&       "include original message in bounce"
 .row &%bounce_return_size_limit%&    "limit on returned message"
 .row &%bounce_sender_authentication%& "send authenticated sender with bounce"
@@ -14094,6 +14105,24 @@ error that is detected during reception, only those header lines preceding the
 point at which the error was detected are returned.
 .cindex "bounce message" "including original"
 
+.option bounce_return_linesize_limit main integer 998
+.cindex "size" "of bounce lines, limit"
+.cindex "bounce message" "line length limit"
+.cindex "limit" "bounce message line length"
+This option sets a limit in bytes on the line length of messages
+that are returned to senders due to delivery problems,
+when &%bounce_return_message%& is true.
+The default value corresponds to RFC limits.
+If the message being returned has lines longer than this value it is
+treated as if the &%bounce_return_size_limit%& (below) restriction was exceeded.
+
+The option also applies to bounces returned when an error is detected
+during reception of a messsage.
+In this case lines from the original are truncated.
+
+The option does not apply to messages generated by an &(autoreply)& transport.
+
+
 .option bounce_return_message main boolean true
 If this option is set false, none of the original message is included in
 bounce messages generated by Exim. See also &%bounce_return_size_limit%& and
@@ -15562,14 +15591,20 @@ local parts. Exim's default configuration does this.
 
 
 .option perl_at_start main boolean false
+.cindex "Perl"
 This option is available only when Exim is built with an embedded Perl
 interpreter. See chapter &<<CHAPperl>>& for details of its use.
 
 
 .option perl_startup main string unset
+.cindex "Perl"
 This option is available only when Exim is built with an embedded Perl
 interpreter. See chapter &<<CHAPperl>>& for details of its use.
 
+.option perl_startup main boolean false
+.cindex "Perl"
+This Option enables the taint mode of the embedded Perl interpreter.
+
 
 .option pgsql_servers main "string list" unset
 .cindex "PostgreSQL lookup type" "server list"
@@ -23398,6 +23433,15 @@ the message. As a result, the overall timeout for a message depends on the size
 of the message. Its value must not be zero. See also &%final_timeout%&.
 
 
+.option dkim_domain smtp string&!! unset
+.option dkim_selector smtp string&!! unset
+.option dkim_private_key smtp string&!! unset
+.option dkim_canon smtp string&!! unset
+.option dkim_strict smtp string&!! unset
+.option dkim_sign_headers smtp string&!! unset
+DKIM signing options.  For details see &<<SECDKIMSIGN>>&.
+
+
 .option delay_after_cutoff smtp boolean true
 This option controls what happens when all remote IP addresses for a given
 domain have been inaccessible for so long that they have passed their retry
@@ -37986,7 +38030,7 @@ where you accept mail from relay sources (internal hosts or authenticated
 senders).
 
 
-.section "Signing outgoing messages" "SECID513"
+.section "Signing outgoing messages" "SECDKIMSIGN"
 .cindex "DKIM" "signing"
 
 Signing is implemented by setting private options on the SMTP transport.
@@ -38001,7 +38045,7 @@ option is put into the &%$dkim_domain%& expansion variable.
 MANDATORY:
 This sets the key selector string. You can use the &%$dkim_domain%& expansion
 variable to look up a matching selector. The result is put in the expansion
-variable &%$dkim_selector%& which should be used in the &%dkim_private_key%&
+variable &%$dkim_selector%& which may be used in the &%dkim_private_key%&
 option along with &%$dkim_domain%&.
 
 .option dkim_private_key smtp string&!! unset