Output dnssec status in -bt/-bv mode

[users/heiko/exim.git] / test / README

diff --git a/test/README b/test/README
index 80c35117b4de9f0605df5de522563a19cfa3954a..2a3fa00c8ec29309f8bdc2b2299e15145c114e62 100644 (file)
--- a/test/README
+++ b/test/README
@@ -79,6 +79,8 @@ In order to run this test suite, the following requirements must be met:
     and "xyz" and single letters that are used in the tests. The test suite
     expects the login to have a gecos name; I think it will now run if the
     gecos field is empty but there may be anomalies.
+    The login must not contain a dash or an equal sign. (Otherwise some tests
+    about local_from_{suffix,prefix} will fail.)
 
 (4) The directory into which you unpack the test suite must be accessible by
     the Exim user, so that code running as exim can access the files therein.
@@ -116,6 +118,9 @@ In order to run this test suite, the following requirements must be met:
 
 (9) Exim must be built with TRUSTED_CONFIG_LIST support, so that the test
     configs can be placed into it.  A suitable file location is .../exim/test/trusted_configs
+    with content .../exim/test/test-config [fill out the ... to make full
+    paths].  This file should be owner/group matching CONFIGURE_OWNER/GROUP,
+    or root/root.  The config files in .../exim/test/confs/ should be owner/group the same.
     DISABLE_D_OPTION must not be used. If ALT_CONFIG_PREFIX is used, it
     must contain the directory of the test-suite.  WHITELIST_D_MACROS should contain:
     
@@ -882,6 +887,11 @@ example:
 Finally, "exim" can be preceded by "sudo", to run Exim as root. If more than
 one of these prefixes is present, they must be in the above order.
 
+If the options include "-DSERVER" but not "-DNOTDAEMON", the script waits for
+Exim to start but then continues without waiting for it to terminate. Typically
+this will be for a daemon-mode "-bd" operation.  The daemon should be later
+terminated using "killdaemon".
+
 
   exim_exim [<options>] [<arguments>]
 
@@ -897,13 +907,15 @@ input, details of which are given below. A number of options are implemented:
 
   -d       causes the server to output debugging information
 
-  -t       sets a timeout in seconds (default 5) for when the server is
+  -t <sec> sets a timeout (default 5) for when the server is
            awaiting an incoming connection
 
   -noipv4  causes the server not to set up an IPv4 socket
 
   -noipv6  causes the server not to set up an IPv6 socket
 
+  -i <sec> sets an initial pause, to delay before creating the listen sockets
+
 By default, in an IPv6 environment, both kinds of socket are set up. However,
 the test script knows which interfaces actually exist on the host, and it adds
 -noipv4 or -noipv6 to the server command as required. An error occurs if both
@@ -1019,7 +1031,10 @@ are of the following kinds:
     (d) If the line starts with ">*eof", nothing is sent and the connection
           is closed.
 
-    The data that is sent starts after the initial '>' sequence.
+    The data that is sent starts after the initial '>' sequence.  Within
+    each line the sequence '\x' followed by two hex digits can be used
+    to specify an arbitrary byte value.  The sequence '\\' specifies a
+    single backslash.
 
 (2) A line that starts with "*sleep" specifies a number of seconds to wait
     before proceeding.
@@ -1033,7 +1048,10 @@ are of the following kinds:
 (5) Otherwise, the line defines the start of an input line that the client
     is expected to send. To allow for lines that start with digits, the line
     may start with '<', which is not taken as part of the input data. If the
-    input does not match, the server bombs out with an error message.
+    lines starts with '<<' then only the characters are expected; no return-
+    linefeed terminator. If the input does not match, the server bombs out
+    with an error message.  Backslash-escape sequences may be used in the
+    line content as for output lines.
 
 Here is a simple example of server use in a test script: