-Transport post-delivery actions
+Event Actions
--------------------------------------------------------------
-An arbitrary per-transport string can be expanded upon various transport events
-and (for SMTP transports) a second string on deferrals caused by a host error.
+(Renamed from TPDA, Transport post-delivery actions)
+
+An arbitrary per-transport string can be expanded upon various transport events.
Additionally a main-section configuration option can be expanded on some
per-message events.
This feature may be used, for example, to write exim internal log information
In order to use the feature, you must compile with
-EXPERIMENTAL_TPDA=yes
+EXPERIMENTAL_EVENT=yes
in your Local/Makefile
and define one or both of
-- the tpda_event_action option in the transport
-- the delivery_event_action
+- the event_action option in the transport
+- the event_action main option
to be expanded when the event fires.
-A new variable, $tpda_event, is set to the event type when the
+A new variable, $event_name, is set to the event type when the
expansion is done. The current list of events is:
- msg:complete main per message
- msg:delivery transport per recipient
- msg:host:defer transport per attempt
- msg:fail:delivery main per recipient
- msg:fail:internal main per recipient
- tcp:connect transport per connection
- tcp:close transport per connection
- tls:cert transport per certificate in verification chain
- smtp:connect transport per connection
-
-The expansion is called for all event types, and should use the $tpda_event
+ msg:complete after main per message
+ msg:delivery after transport per recipient
+ msg:host:defer after transport per attempt
+ msg:fail:delivery after main per recipient
+ msg:fail:internal after main per recipient
+ tcp:connect before transport per connection
+ tcp:close after transport per connection
+ tls:cert before both per certificate in verification chain
+ smtp:connect after transport per connection
+
+The expansion is called for all event types, and should use the $event_name
value to decide when to act. The variable data is a colon-separated
list, describing an event tree.
-There is an auxilary variable, $tpda_data, for which the
+There is an auxilary variable, $event_data, for which the
content is event_dependent:
msg:delivery smtp confirmation mssage
tls:cert verification chain depth
smtp:connect smtp banner
-The msg:host:defer event populates one extra variable, $tpda_defer_errno.
+The msg:host:defer event populates one extra variable, $event_defer_errno.
The following variables are likely to be useful depending on the event type:
tls_out_peercert
lookup_dnssec_authenticated, tls_out_dane
sending_ip_address, sending_port
- message_exim_id
+ message_exim_id, verify_mode
An example might look like:
-tpda_event_action = ${if = {msg:delivery}{$tpda_event} \
+event_action = ${if = {msg:delivery}{$event_name} \
{${lookup pgsql {SELECT * FROM record_Delivery( \
'${quote_pgsql:$sender_address_domain}',\
'${quote_pgsql:${lc:$sender_address_local_part}}', \
'${quote_pgsql:$message_exim_id}')}} \
} {}}
-The string is expanded for each of the supported events and any
-side-effects will happen. The result is then discarded.
+The string is expanded when each of the supported events occur
+and any side-effects of the expansion will happen.
Note that for complex operations an ACL expansion can be used.
-The expansion of the tpda_event_action option should normally
+The expansion of the event_action option should normally
return an empty string. Should it return anything else the
following will be forced:
tls:cert refuse verification
smtp:connect close connection
+No other use is made of the result string.
+Known issues:
+- the tls:cert event is only called for the cert chain elements
+ received over the wire, with GnuTLS. OpenSSL gives the entire
+ chain including thse loaded locally.
Redis Lookup
Adding it to a redirect router makes no difference.
+
+
Certificate name checking
--------------------------------------------------------------
The X509 certificates used for TLS are supposed be verified
support to date has not made these checks.
If built with EXPERIMENTAL_CERTNAMES defined, code is
-included to do so, and a new smtp transport option
-"tls_verify_cert_hostname" supported which takes a list of
-names for which the checks must be made. The host must
-also be in "tls_verify_hosts".
+included to do so for server certificates, and a new smtp transport option
+"tls_verify_cert_hostnames" supported which takes a hostlist
+which must match the target host for the additional checks must be made.
+The option currently defaults to empty, but this may change in
+the future. "*" is probably a suitable value.
+Whether certificate verification is done at all, and the result of
+it failing, is stll under the control of "tls_verify_hosts" nad
+"tls_try_verify_hosts".
+
+The name being checked is that for the host, generally
+the result of an MX lookup.
Both Subject and Subject-Alternate-Name certificate fields
are supported, as are wildcard certificates (limited to
a single wildcard being the initial component of a 3-or-more
component FQDN).
+The equivalent check on the server for client certificates is not
+implemented. At least one major email provider is using a client
+certificate which fails this check. They do not retry either without
+the client certificate or in clear.
+
+It is possible to duplicate the effect of this checking by
+creative use of Events.
+
+
+
DANE
------------------------------------------------------------
There is a new variable $tls_out_dane which will have "yes" if
verification succeeded using DANE and "no" otherwise (only useful
-in combination with EXPERIMENTAL_TPDA), and a new variable
+in combination with EXPERIMENTAL_EVENT), and a new variable
$tls_out_tlsa_usage (detailed above).
git://git.exim.org / users / heiko / exim.git / blobdiff