liable to incompatible change.
-PRDR support
---------------------------------------------------------------
-
-Per-Recipient Data Reponse is an SMTP extension proposed by Eric Hall
-in a (now-expired) IETF draft from 2007. It's not hit mainstream
-use, but has apparently been implemented in the META1 MTA.
-
-There is mention at http://mail.aegee.org/intern/sendmail.html
-of a patch to sendmail "to make it PRDR capable".
-
- ref: http://www.eric-a-hall.com/specs/draft-hall-prdr-00.txt
-
-If Exim is built with EXPERIMENTAL_PRDR there is a new config
-boolean "prdr_enable" which controls whether PRDR is advertised
-as part of an EHLO response, a new "acl_data_smtp_prdr" ACL
-(called for each recipient, after data arrives but before the
-data ACL), and a new smtp transport option "hosts_try_prdr".
-
-PRDR may be used to support per-user content filtering. Without it
-one must defer any recipient after the first that has a different
-content-filter configuration. With PRDR, the RCPT-time check
-for this can be disabled when the MAIL-time $smtp_command included
-"PRDR". Any required difference in behaviour of the main DATA-time
-ACL should however depend on the PRDR-time ACL having run, as Exim
-will avoid doing so in some situations (eg. single-recipient mails).
-
-
-
-OCSP Stapling support
---------------------------------------------------------------
-
-X.509 PKI certificates expire and can be revoked; to handle this, the
-clients need some way to determine if a particular certificate, from a
-particular Certificate Authority (CA), is still valid. There are three
-main ways to do so.
-
-The simplest way is to serve up a Certificate Revocation List (CRL) with
-an ordinary web-server, regenerating the CRL before it expires. The
-downside is that clients have to periodically re-download a potentially
-huge file from every certificate authority it knows of.
-
-The way with most moving parts at query time is Online Certificate
-Status Protocol (OCSP), where the client verifies the certificate
-against an OCSP server run by the CA. This lets the CA track all
-usage of the certs. This requires running software with access to the
-private key of the CA, to sign the responses to the OCSP queries. OCSP
-is based on HTTP and can be proxied accordingly.
-
-The only widespread OCSP server implementation (known to this writer)
-comes as part of OpenSSL and aborts on an invalid request, such as
-connecting to the port and then disconnecting. This requires
-re-entering the passphrase each time some random client does this.
-
-The third way is OCSP Stapling; in this, the server using a certificate
-issued by the CA periodically requests an OCSP proof of validity from
-the OCSP server, then serves it up inline as part of the TLS
-negotiation. This approach adds no extra round trips, does not let the
-CA track users, scales well with number of certs issued by the CA and is
-resilient to temporary OCSP server failures, as long as the server
-starts retrying to fetch an OCSP proof some time before its current
-proof expires. The downside is that it requires server support.
-
-If Exim is built with EXPERIMENTAL_OCSP and it was built with OpenSSL,
-then it gains a new global option: "tls_ocsp_file".
-
-The file specified therein is expected to be in DER format, and contain
-an OCSP proof. Exim will serve it as part of the TLS handshake. This
-option will be re-expanded for SNI, if the tls_certificate option
-contains $tls_sni, as per other TLS options.
-
-Exim does not at this time implement any support for fetching a new OCSP
-proof. The burden is on the administrator to handle this, outside of
-Exim. The file specified should be replaced atomically, so that the
-contents are always valid. Exim will expand the "tls_ocsp_file" option
-on each connection, so a new file will be handled transparently on the
-next connection.
-
-Exim will check for a valid next update timestamp in the OCSP proof;
-if not present, or if the proof has expired, it will be ignored.
-
-Also, given EXPERIMENTAL_OCSP and OpenSSL, the smtp transport gains
-a "hosts_require_ocsp" option; a host-list for which an OCSP Stapling
-is requested and required for the connection to proceed. The host(s)
-should also be in "hosts_require_tls", and "tls_verify_certificates"
-configured for the transport.
-
-For the client to be able to verify the stapled OCSP the server must
-also supply, in its stapled information, any intermediate
-certificates for the chain leading to the OCSP proof from the signer
-of the server certificate. There may be zero or one such. These
-intermediate certificates should be added to the server OCSP stapling
-file (named by tls_ocsp_file).
-
-At this point in time, we're gathering feedback on use, to determine if
-it's worth adding complexity to the Exim daemon to periodically re-fetch
-OCSP files and somehow handling multiple files.
-
- A helper script "ocsp_fetch.pl" for fetching a proof from a CA
- OCSP server is supplied. The server URL may be included in the
- server certificate, if the CA is helpful.
-
- One fail mode seen was the OCSP Signer cert expiring before the end
- of vailidity of the OCSP proof. The checking done by Exim/OpenSSL
- noted this as invalid overall, but the re-fetch script did not.
-
-
-
-
-Brightmail AntiSpam (BMI) suppport
+Brightmail AntiSpam (BMI) support
--------------------------------------------------------------
Brightmail AntiSpam is a commercial package. Please see
1) Adding support for BMI at compile time
To compile with BMI support, you need to link Exim against
- the Brighmail client SDK, consisting of a library
+ the Brightmail client SDK, consisting of a library
(libbmiclient_single.so) and a header file (bmi_api.h).
You'll also need to explicitly set a flag in the Makefile to
include BMI support in the Exim binary. Both can be achieved
-Sender Policy Framework (SPF) support
---------------------------------------------------------------
-
-To learn more about SPF, visit http://www.openspf.org. This
-document does not explain the SPF fundamentals, you should
-read and understand the implications of deploying SPF on your
-system before doing so.
-
-SPF support is added via the libspf2 library. Visit
-
- http://www.libspf2.org/
-
-to obtain a copy, then compile and install it. By default,
-this will put headers in /usr/local/include and the static
-library in /usr/local/lib.
-
-To compile Exim with SPF support, set these additional flags in
-Local/Makefile:
-
-EXPERIMENTAL_SPF=yes
-CFLAGS=-DSPF -I/usr/local/include
-EXTRALIBS_EXIM=-L/usr/local/lib -lspf2
-
-This assumes that the libspf2 files are installed in
-their default locations.
-
-You can now run SPF checks in incoming SMTP by using the "spf"
-ACL condition in either the MAIL, RCPT or DATA ACLs. When
-using it in the RCPT ACL, you can make the checks dependent on
-the RCPT address (or domain), so you can check SPF records
-only for certain target domains. This gives you the
-possibility to opt-out certain customers that do not want
-their mail to be subject to SPF checking.
-
-The spf condition takes a list of strings on its right-hand
-side. These strings describe the outcome of the SPF check for
-which the spf condition should succeed. Valid strings are:
-
- o pass The SPF check passed, the sending host
- is positively verified by SPF.
- o fail The SPF check failed, the sending host
- is NOT allowed to send mail for the domain
- in the envelope-from address.
- o softfail The SPF check failed, but the queried
- domain can't absolutely confirm that this
- is a forgery.
- o none The queried domain does not publish SPF
- records.
- o neutral The SPF check returned a "neutral" state.
- This means the queried domain has published
- a SPF record, but wants to allow outside
- servers to send mail under its domain as well.
- o err_perm This indicates a syntax error in the SPF
- record of the queried domain. This should be
- treated like "none".
- o err_temp This indicates a temporary error during all
- processing, including Exim's SPF processing.
- You may defer messages when this occurs.
-
-You can prefix each string with an exclamation mark to invert
-is meaning, for example "!fail" will match all results but
-"fail". The string list is evaluated left-to-right, in a
-short-circuit fashion. When a string matches the outcome of
-the SPF check, the condition succeeds. If none of the listed
-strings matches the outcome of the SPF check, the condition
-fails.
-
-Here is an example to fail forgery attempts from domains that
-publish SPF records:
-
-/* -----------------
-deny message = $sender_host_address is not allowed to send mail from ${if def:sender_address_domain {$sender_address_domain}{$sender_helo_name}}. \
- Please see http://www.openspf.org/Why?scope=${if def:sender_address_domain {mfrom}{helo}};identity=${if def:sender_address_domain {$sender_address}{$sender_helo_name}};ip=$sender_host_address
- spf = fail
---------------------- */
-
-You can also give special treatment to specific domains:
-
-/* -----------------
-deny message = AOL sender, but not from AOL-approved relay.
- sender_domains = aol.com
- spf = fail:neutral
---------------------- */
-
-Explanation: AOL publishes SPF records, but is liberal and
-still allows non-approved relays to send mail from aol.com.
-This will result in a "neutral" state, while mail from genuine
-AOL servers will result in "pass". The example above takes
-this into account and treats "neutral" like "fail", but only
-for aol.com. Please note that this violates the SPF draft.
-
-When the spf condition has run, it sets up several expansion
-variables.
-
- $spf_header_comment
- This contains a human-readable string describing the outcome
- of the SPF check. You can add it to a custom header or use
- it for logging purposes.
-
- $spf_received
- This contains a complete Received-SPF: header that can be
- added to the message. Please note that according to the SPF
- draft, this header must be added at the top of the header
- list. Please see section 10 on how you can do this.
-
- Note: in case of "Best-guess" (see below), the convention is
- to put this string in a header called X-SPF-Guess: instead.
-
- $spf_result
- This contains the outcome of the SPF check in string form,
- one of pass, fail, softfail, none, neutral, err_perm or
- err_temp.
-
- $spf_smtp_comment
- This contains a string that can be used in a SMTP response
- to the calling party. Useful for "fail".
-
-In addition to SPF, you can also perform checks for so-called
-"Best-guess". Strictly speaking, "Best-guess" is not standard
-SPF, but it is supported by the same framework that enables SPF
-capability. Refer to http://www.openspf.org/FAQ/Best_guess_record
-for a description of what it means.
-
-To access this feature, simply use the spf_guess condition in place
-of the spf one. For example:
-
-/* -----------------
-deny message = $sender_host_address doesn't look trustworthy to me
- spf_guess = fail
---------------------- */
-
-In case you decide to reject messages based on this check, you
-should note that although it uses the same framework, "Best-guess"
-is NOT SPF, and therefore you should not mention SPF at all in your
-reject message.
-
-When the spf_guess condition has run, it sets up the same expansion
-variables as when spf condition is run, described above.
-
-Additionally, since Best-guess is not standardized, you may redefine
-what "Best-guess" means to you by redefining spf_guess variable in
-global config. For example, the following:
-
-/* -----------------
-spf_guess = v=spf1 a/16 mx/16 ptr ?all
---------------------- */
-
-would relax host matching rules to a broader network range.
-
-
-SRS (Sender Rewriting Scheme) Support
+SRS (Sender Rewriting Scheme) Support (using libsrs_alt)
--------------------------------------------------------------
+See also the main docs, for an alternative native support implementation.
-Exiscan currently includes SRS support via Miles Wilton's
+Exim can be built with SRS support using Miles Wilton's
libsrs_alt library. The current version of the supported
-library is 0.5.
+library is 0.5, there are reports of 1.0 working.
In order to use SRS, you must get a copy of libsrs_alt from
-http://srs.mirtol.com/
+https://opsec.eu/src/srs/
+
+(not the original source, which has disappeared.)
Unpack the tarball, then refer to MTAs/README.EXIM
to proceed. You need to set
-EXPERIMENTAL_SRS=yes
+EXPERIMENTAL_SRS_ALT=yes
in your Local/Makefile.
+The built-in support, included by SUPPORT_SRS,
+shuold *not* be enabled if you wish to use the libsrs_alt
+version.
+
+The following main-section options become available:
+ srs_config string
+ srs_hashlength int
+ srs_hashmin int
+ srs_maxage int
+ srs_secrets string
+ srs_usehash bool
+ srs_usetimestamp bool
+
+The redirect router gains these options (all of type string, unset by default):
+ srs
+ srs_alias
+ srs_condition
+ srs_dbinsert
+ srs_dbselect
+
+The following variables become available:
+ $srs_db_address
+ $srs_db_key
+ $srs_orig_recipient
+ $srs_orig_sender
+ $srs_recipient
+ $srs_status
+
+The predefined feature-macro _HAVE_SRS will be present.
+Additional delivery log line elements, tagged with "SRS=" will show the srs sender.
+For configuration information see https://github.com/Exim/exim/wiki/SRS .
+
+
+
DCC Support
--------------------------------------------------------------
+Distributed Checksum Clearinghouse; http://www.rhyolite.com/dcc/
*) Building exim
mout-xforward.gmx.net 82.165.159.12
mout.gmx.net 212.227.15.16
-Use a reasonable IP. eg. one the sending cluster acutally uses.
+Use a reasonable IP. eg. one the sending cluster actually uses.
-DMARC Support
---------------------------------------------------------------
-DMARC combines feedback from SPF, DKIM, and header From: in order
-to attempt to provide better indicators of the authenticity of an
-email. This document does not explain the fundamentals, you
-should read and understand how it works by visiting the website at
-http://www.dmarc.org/.
-
-DMARC support is added via the libopendmarc library. Visit:
-
- http://sourceforge.net/projects/opendmarc/
-
-to obtain a copy, or find it in your favorite rpm package
-repository. If building from source, this description assumes
-that headers will be in /usr/local/include, and that the libraries
-are in /usr/local/lib.
-
-1. To compile Exim with DMARC support, you must first enable SPF.
-Please read the above section on enabling the EXPERIMENTAL_SPF
-feature. You must also have DKIM support, so you cannot set the
-DISABLE_DKIM feature. Once both of those conditions have been met
-you can enable DMARC in Local/Makefile:
-
-EXPERIMENTAL_DMARC=yes
-LDFLAGS += -lopendmarc
-# CFLAGS += -I/usr/local/include
-# LDFLAGS += -L/usr/local/lib
-
-The first line sets the feature to include the correct code, and
-the second line says to link the libopendmarc libraries into the
-exim binary. The commented out lines should be uncommented if you
-built opendmarc from source and installed in the default location.
-Adjust the paths if you installed them elsewhere, but you do not
-need to uncomment them if an rpm (or you) installed them in the
-package controlled locations (/usr/include and /usr/lib).
-
-
-2. Use the following global settings to configure DMARC:
-
-Required:
-dmarc_tld_file Defines the location of a text file of valid
- top level domains the opendmarc library uses
- during domain parsing. Maintained by Mozilla,
- the most current version can be downloaded
- from a link at http://publicsuffix.org/list/.
-
-Optional:
-dmarc_history_file Defines the location of a file to log results
- of dmarc verification on inbound emails. The
- contents are importable by the opendmarc tools
- which will manage the data, send out DMARC
- reports, and expire the data. Make sure the
- directory of this file is writable by the user
- exim runs as.
-
-dmarc_forensic_sender The email address to use when sending a
- forensic report detailing alignment failures
- if a sender domain's dmarc record specifies it
- and you have configured Exim to send them.
- Default: do-not-reply@$default_hostname
-
-
-3. By default, the DMARC processing will run for any remote,
-non-authenticated user. It makes sense to only verify DMARC
-status of messages coming from remote, untrusted sources. You can
-use standard conditions such as hosts, senders, etc, to decide that
-DMARC verification should *not* be performed for them and disable
-DMARC with a control setting:
-
- control = dmarc_disable_verify
-
-A DMARC record can also specify a "forensic address", which gives
-exim an email address to submit reports about failed alignment.
-Exim does not do this by default because in certain conditions it
-results in unintended information leakage (what lists a user might
-be subscribed to, etc). You must configure exim to submit forensic
-reports to the owner of the domain. If the DMARC record contains a
-forensic address and you specify the control statement below, then
-exim will send these forensic emails. It's also advised that you
-configure a dmarc_forensic_sender because the default sender address
-construction might be inadequate.
-
- control = dmarc_forensic_enable
-
-(AGAIN: You can choose not to send these forensic reports by simply
-not putting the dmarc_forensic_enable control line at any point in
-your exim config. If you don't tell it to send them, it will not
-send them.)
-
-There are no options to either control. Both must appear before
-the DATA acl.
-
-
-4. You can now run DMARC checks in incoming SMTP by using the
-"dmarc_status" ACL condition in the DATA ACL. You are required to
-call the spf condition first in the ACLs, then the "dmarc_status"
-condition. Putting this condition in the ACLs is required in order
-for a DMARC check to actually occur. All of the variables are set
-up before the DATA ACL, but there is no actual DMARC check that
-occurs until a "dmarc_status" condition is encountered in the ACLs.
-
-The dmarc_status condition takes a list of strings on its
-right-hand side. These strings describe recommended action based
-on the DMARC check. To understand what the policy recommendations
-mean, refer to the DMARC website above. Valid strings are:
-
- o accept The DMARC check passed and the library recommends
- accepting the email.
- o reject The DMARC check failed and the library recommends
- rejecting the email.
- o quarantine The DMARC check failed and the library recommends
- keeping it for further inspection.
- o norecord No policy section in the DMARC record for this
- sender domain.
- o nofrom Unable to determine the domain of the sender.
- o none There is no DMARC record for this sender domain.
- o error Library error or dns error.
-
-You can prefix each string with an exclamation mark to invert its
-meaning, for example "!accept" will match all results but
-"accept". The string list is evaluated left-to-right in a
-short-circuit fashion. When a string matches the outcome of the
-DMARC check, the condition succeeds. If none of the listed
-strings matches the outcome of the DMARC check, the condition
-fails.
-
-Of course, you can also use any other lookup method that Exim
-supports, including LDAP, Postgres, MySQL, etc, as long as the
-result is a list of colon-separated strings;
-
-Several expansion variables are set before the DATA ACL is
-processed, and you can use them in this ACL. The following
-expansion variables are available:
-
- o $dmarc_status
- This is a one word status indicating what the DMARC library
- thinks of the email.
-
- o $dmarc_status_text
- This is a slightly longer, human readable status.
-
- o $dmarc_used_domain
- This is the domain which DMARC used to look up the DMARC
- policy record.
-
- o $dmarc_ar_header
- This is the entire Authentication-Results header which you can
- add using an add_header modifier.
-
-
-5. How to enable DMARC advanced operation:
-By default, Exim's DMARC configuration is intended to be
-non-intrusive and conservative. To facilitate this, Exim will not
-create any type of logging files without explicit configuration by
-you, the admin. Nor will Exim send out any emails/reports about
-DMARC issues without explicit configuration by you, the admin (other
-than typical bounce messages that may come about due to ACL
-processing or failure delivery issues).
-
-In order to log statistics suitable to be imported by the opendmarc
-tools, you need to:
-a. Configure the global setting dmarc_history_file.
-b. Configure cron jobs to call the appropriate opendmarc history
- import scripts and truncating the dmarc_history_file.
-
-In order to send forensic reports, you need to:
-a. Configure the global setting dmarc_forensic_sender.
-b. Configure, somewhere before the DATA ACL, the control option to
- enable sending DMARC forensic reports.
-
-
-6. Example usage:
-(RCPT ACL)
- warn domains = +local_domains
- hosts = +local_hosts
- control = dmarc_disable_verify
-
- warn !domains = +screwed_up_dmarc_records
- control = dmarc_enable_forensic
-
-(DATA ACL)
- warn dmarc_status = accept : none : off
- !authenticated = *
- log_message = DMARC DEBUG: $dmarc_status $dmarc_used_domain
- add_header = $dmarc_ar_header
-
- warn dmarc_status = !accept
- !authenticated = *
- log_message = DMARC DEBUG: '$dmarc_status' for $dmarc_used_domain
-
- warn dmarc_status = quarantine
- !authenticated = *
- set $acl_m_quarantine = 1
- # Do something in a transport with this flag variable
-
- deny dmarc_status = reject
- !authenticated = *
- message = Message from $domain_used_domain failed sender's DMARC policy, REJECT
-
-
-
-Transport post-delivery actions
---------------------------------------------------------------
-An arbitrary per-transport string can be expanded on successful delivery,
-and (for SMTP transports) a second string on deferrals caused by a host error.
-This feature may be used, for example, to write exim internal log information
-(not available otherwise) into a database.
+DSN extra information
+---------------------
+If compiled with EXPERIMENTAL_DSN_INFO extra information will be added
+to DSN fail messages ("bounces"), when available. The intent is to aid
+tracing of specific failing messages, when presented with a "bounce"
+complaint and needing to search logs.
+
+
+The remote MTA IP address, with port number if nonstandard.
+Example:
+ Remote-MTA: X-ip; [127.0.0.1]:587
+Rationale:
+ Several addresses may correspond to the (already available)
+ dns name for the remote MTA.
+
+The remote MTA connect-time greeting.
+Example:
+ X-Remote-MTA-smtp-greeting: X-str; 220 the.local.host.name ESMTP Exim x.yz Tue, 2 Mar 1999 09:44:33 +0000
+Rationale:
+ This string sometimes presents the remote MTA's idea of its
+ own name, and sometimes identifies the MTA software.
+
+The remote MTA response to HELO or EHLO.
+Example:
+ X-Remote-MTA-helo-response: X-str; 250-the.local.host.name Hello localhost [127.0.0.1]
+Limitations:
+ Only the first line of a multiline response is recorded.
+Rationale:
+ This string sometimes presents the remote MTA's view of
+ the peer IP connecting to it.
+
+The reporting MTA detailed diagnostic.
+Example:
+ X-Exim-Diagnostic: X-str; SMTP error from remote mail server after RCPT TO:<d3@myhost.test.ex>: 550 hard error
+Rationale:
+ This string sometimes give extra information over the
+ existing (already available) Diagnostic-Code field.
+
+
+Note that non-RFC-documented field names and data types are used.
+
-In order to use the feature, you must set
+Queuefile transport
+-------------------
+Queuefile is a pseudo transport which does not perform final delivery.
+It simply copies the exim spool files out of the spool directory into
+an external directory retaining the exim spool format.
-EXPERIMENTAL_TPDA=yes
+The spool files can then be processed by external processes and then
+requeued into exim spool directories for final delivery.
+However, note carefully the warnings in the main documentation on
+qpool file formats.
-in your Local/Makefile
+The motivation/inspiration for the transport is to allow external
+processes to access email queued by exim and have access to all the
+information which would not be available if the messages were delivered
+to the process in the standard email formats.
-and define the expandable strings in the runtime config file, to
-be executed at end of delivery.
+The mailscanner package is one of the processes that can take advantage
+of this transport to filter email.
-Additionally, there are 6 more variables, available at end of
-delivery:
+The transport can be used in the same way as the other existing transports,
+i.e by configuring a router to route mail to a transport configured with
+the queuefile driver.
-tpda_delivery_ip IP of host, which has accepted delivery
-tpda_delivery_port Port of remote host which has accepted delivery
-tpda_delivery_fqdn FQDN of host, which has accepted delivery
-tpda_delivery_local_part local part of address being delivered
-tpda_delivery_domain domain part of address being delivered
-tpda_delivery_confirmation SMTP confirmation message
+The transport only takes one option:
-In case of a deferral caused by a host-error:
-tpda_defer_errno Error number
-tpda_defer_errstr Error string possibly containing more details
+* directory - This is used to specify the directory messages should be
+copied to. Expanded.
-The $router_name and $transport_name variables are also usable.
+The generic transport options (body_only, current_directory, disable_logging,
+debug_print, delivery_date_add, envelope_to_add, event_action, group,
+headers_add, headers_only, headers_remove, headers_rewrite, home_directory,
+initgroups, max_parallel, message_size_limit, rcpt_include_affixes,
+retry_use_local_part, return_path, return_path_add, shadow_condition,
+shadow_transport, transport_filter, transport_filter_timeout, user) are
+ignored.
+Sample configuration:
-To take action after successful deliveries, set the following option
-on any transport of interest.
+(Router)
-tpda_delivery_action
+scan:
+ driver = accept
+ transport = scan
-An example might look like:
+(Transport)
-tpda_delivery_action = \
-${lookup pgsql {SELECT * FROM record_Delivery( \
- '${quote_pgsql:$sender_address_domain}',\
- '${quote_pgsql:${lc:$sender_address_local_part}}', \
- '${quote_pgsql:$tpda_delivery_domain}', \
- '${quote_pgsql:${lc:$tpda_delivery_local_part}}', \
- '${quote_pgsql:$tpda_delivery_ip}', \
- '${quote_pgsql:${lc:$tpda_delivery_fqdn}}', \
- '${quote_pgsql:$message_exim_id}')}}
+scan:
+ driver = queuefile
+ directory = /var/spool/baruwa-scanner/input
-The string is expanded after the delivery completes and any
-side-effects will happen. The result is then discarded.
-Note that for complex operations an ACL expansion can be used.
+In order to build exim with Queuefile transport support add or uncomment
-In order to log host deferrals, add the following option to an SMTP
-transport:
+EXPERIMENTAL_QUEUEFILE=yes
-tpda_host_defer_action
+to your Local/Makefile. (Re-)build/install exim. exim -d should show
+Experimental_QUEUEFILE in the line "Support for:".
-This is a private option of the SMTP transport. It is intended to
-log failures of remote hosts. It is executed only when exim has
-attempted to deliver a message to a remote host and failed due to
-an error which doesn't seem to be related to the individual
-message, sender, or recipient address.
-See section 45.2 of the exim documentation for more details on how
-this is determined.
+
+ARC support
+-----------
+Specification: https://tools.ietf.org/html/draft-ietf-dmarc-arc-protocol-11
+Note that this is not an RFC yet, so may change.
+
+[RFC 8617 was published 2019/06. Draft 11 was 2018/01. A review of the
+changes has not yet been done]
+
+ARC is intended to support the utility of SPF and DKIM in the presence of
+intermediaries in the transmission path - forwarders and mailinglists -
+by establishing a cryptographically-signed chain in headers.
+
+Normally one would only bother doing ARC-signing when functioning as
+an intermediary. One might do verify for local destinations.
+
+ARC uses the notion of a "ADministrative Management Domain" (ADMD).
+Described in RFC 5598 (section 2.3), this is essentially a set of
+mail-handling systems that mail transits that are all under the control
+of one organisation. A label should be chosen to identify the ADMD.
+Messages should be ARC-verified on entry to the ADMD, and ARC-signed on exit
+from it.
+
+
+Building with ARC Support
+--
+Enable using EXPERIMENTAL_ARC=yes in your Local/Makefile.
+You must also have DKIM present (not disabled), and you very likely
+want to have SPF enabled.
+
+
+Verification
+--
+An ACL condition is provided to perform the "verifier actions" detailed
+in section 6 of the above specification. It may be called from the DATA ACL
+and succeeds if the result matches any of a given list.
+It also records the highest ARC instance number (the chain size)
+and verification result for later use in creating an Authentication-Results:
+standard header.
+
+ verify = arc/<acceptable_list> none:fail:pass
+
+ add_header = :at_start:${authresults {<admd-identifier>}}
+
+ Note that it would be wise to strip incoming messages of A-R headers
+ that claim to be from our own <admd-identifier>.
+
+There are four new variables:
+
+ $arc_state One of pass, fail, none
+ $arc_state_reason (if fail, why)
+ $arc_domains colon-sep list of ARC chain domains, in chain order.
+ problematic elements may have empty list elements
+ $arc_oldest_pass lowest passing instance number of chain
Example:
+ logwrite = oldest-p-ams: <${reduce {$lh_ARC-Authentication-Results:} \
+ {} \
+ {${if = {$arc_oldest_pass} \
+ {${extract {i}{${extract {1}{;}{$item}}}}} \
+ {$item} {$value}}} \
+ }>
+
+Receive log lines for an ARC pass will be tagged "ARC".
+
+
+Signing
+--
+arc_sign = <admd-identifier> : <selector> : <privkey> [ : <options> ]
+An option on the smtp transport, which constructs and prepends to the message
+an ARC set of headers. The textually-first Authentication-Results: header
+is used as a basis (you must have added one on entry to the ADMD).
+Expanded as a whole; if unset, empty or forced-failure then no signing is done.
+If it is set, all of the first three elements must be non-empty.
+
+The fourth element is optional, and if present consists of a comma-separated list
+of options. The options implemented are
+
+ timestamps Add a t= tag to the generated AMS and AS headers, with the
+ current time.
+ expire[=<val>] Add an x= tag to the generated AMS header, with an expiry time.
+ If the value <val> is an plain number it is used unchanged.
+ If it starts with a '+' then the following number is added
+ to the current time, as an offset in seconds.
+ If a value is not given it defaults to a one month offset.
+
+[As of writing, gmail insist that a t= tag on the AS is mandatory]
+
+Caveats:
+ * There must be an Authentication-Results header, presumably added by an ACL
+ while receiving the message, for the same ADMD, for arc_sign to succeed.
+ This requires careful coordination between inbound and outbound logic.
+
+ Only one A-R header is taken account of. This is a limitation versus
+ the ARC spec (which says that all A-R headers from within the ADMD must
+ be used).
+
+ * If passing a message to another system, such as a mailing-list manager
+ (MLM), between receipt and sending, be wary of manipulations to headers made
+ by the MLM.
+ + For instance, Mailman with REMOVE_DKIM_HEADERS==3 might improve
+ deliverability in a pre-ARC world, but that option also renames the
+ Authentication-Results header, which breaks signing.
+
+ * Even if you use multiple DKIM keys for different domains, the ARC concept
+ should try to stick to one ADMD, so pick a primary domain and use that for
+ AR headers and outbound signing.
+
+Signing is not compatible with cutthrough delivery; any (before expansion)
+value set for the option will result in cutthrough delivery not being
+used via the transport in question.
+
+
+
+Dovecot authenticator via inet socket
+--------------------------------------------------------------
+If Dovecot is configured similar to :-
+
+service auth {
+...
+#SASL
+ inet_listener {
+ name = exim
+ port = 12345
+ }
+...
+}
+
+then an Exim authenticator can be configured :-
+
+ dovecot-plain:
+ driver = dovecot
+ public_name = PLAIN
+ server_socket = dovecot_server_name 12345
+ server_tls = true
+ server_set_id = $auth1
+
+If the server_socket does not start with a / it is taken as a hostname (or IP);
+and a whitespace-separated port number must be given.
+
-tpda_host_defer_action = \
-${lookup mysql {insert into delivlog set \
- msgid = '${quote_mysql:$message_exim_id}', \
- senderlp = '${quote_mysql:${lc:$sender_address_local_part}}', \
- senderdom = '${quote_mysql:$sender_address_domain}', \
- delivlp = '${quote_mysql:${lc:$tpda_delivery_local_part}}', \
- delivdom = '${quote_mysql:$tpda_delivery_domain}', \
- delivip = '${quote_mysql:$tpda_delivery_ip}', \
- delivport = '${quote_mysql:$tpda_delivery_port}', \
- delivfqdn = '${quote_mysql:$tpda_delivery_fqdn}', \
- deliverrno = '${quote_mysql:$tpda_defer_errno}', \
- deliverrstr = '${quote_mysql:$tpda_defer_errstr}' \
- }}
--------------------------------------------------------------
End of file
git://git.exim.org / users / heiko / exim.git / blobdiff