The SIGHUP signal
.cindex "SIGHUP"
.cindex "daemon" "restarting"
+.cindex signal "to reload configuration"
+.cindex daemon "reload configuration"
can be used to cause the daemon to re-execute itself. This should be done
whenever Exim's configuration file, or any file that is incorporated into it by
means of the &%.include%& facility, is changed, and also whenever a new version
&*Warning 2*&: In a host list, you must always use &(net-iplsearch)& so that
the implicit key is the host's IP address rather than its name (see section
&<<SECThoslispatsikey>>&).
+
+.new
+&*Warning 3*&: Do not use an IPv4-mapped IPv6 address for a key; use the
+IPv4, in dotted-quad form. (Exim converts IPv4-mapped IPv6 addresses to this
+notation before executing the lookup.)
+.wen
.next
.new
.cindex lookup json
recently implemented &(iplsearch)& files do require colons in IPv6 keys
(notated using the quoting facility) so as to distinguish them from IPv4 keys.
For this reason, when the lookup type is &(iplsearch)&, IPv6 addresses are
-converted using colons and not dots. In all cases, full, unabbreviated IPv6
+converted using colons and not dots.
+.new
+In all cases except IPv4-mapped IPv6, full, unabbreviated IPv6
addresses are always used.
+The latter are converted to IPv4 addresses, in dotted-quad form.
+.wen
Ideally, it would be nice to tidy up this anomalous situation by changing to
colons in all cases, given that quoting is now available for &(lsearch)&.
transport driver.
-.option openssl_options main "string list" "+no_sslv2 +single_dh_use +no_ticket"
+.option openssl_options main "string list" "+no_sslv2 +no_sslv3 +single_dh_use +no_ticket"
.cindex "OpenSSL "compatibility options"
This option allows an administrator to adjust the SSL options applied
by OpenSSL to connections. It is given as a space-separated list of items,
-.section "Configuring an Exim client to use TLS" "SECID185"
+.section "Configuring an Exim client to use TLS" "SECTclientTLS"
.cindex "cipher" "logging"
.cindex "log" "TLS cipher"
.cindex "log" "distinguished name"
option), this condition is always true.
-.vitem &*verify&~=&~not_blind*&
+.vitem &*verify&~=&~not_blind/*&<&'options'&>
.cindex "verifying" "not blind"
.cindex "bcc recipients, verifying none"
This condition checks that there are no blind (bcc) recipients in the message.
&'Resent-Cc:'& header lines exist, they are also checked. This condition can be
used only in a DATA or non-SMTP ACL.
+.new
+There is one possible option, &`case_insensitive`&. If this is present then
+local parts are checked case-insensitively.
+.wen
+
There are, of course, many legitimate messages that make use of blind (bcc)
recipients. This check should not be used on its own for blocking messages.
&`F `& sender address (on delivery lines)
&`H `& host name and IP address
&`I `& local interface used
-&`id `& message id for incoming message
+&`id `& message id (from header) for incoming message
&`K `& CHUNKING extension used
&`L `& on &`<=`& and &`=>`& lines: PIPELINING extension used
&`M8S `& 8BITMIME status for incoming message
&` incoming_port `& remote port on <= lines
&`*lost_incoming_connection `& as it says (includes timeouts)
&` millisec `& millisecond timestamps and RT,QT,DT,D times
+&`*msg_id `& on <= lines, Message-ID: header value
+&` msg_id_created `& on <= lines, Message-ID: header value when one had to be added
&` outgoing_interface `& local interface on => lines
&` outgoing_port `& add remote port to => lines
&`*queue_run `& start and end queue runs
&%millisec%&: Timestamps have a period and three decimal places of finer granularity
appended to the seconds value.
.next
+.new
+.cindex "log" "message id"
+&%msg_id%&: The value of the Message-ID: header.
+.next
+&%msg_id_created%&: The value of the Message-ID: header, when one had to be created.
+This will be either because the message is a bounce, or was submitted locally
+(submission mode) without one.
+The field identifier will have an asterix appended: &"id*="&.
+.wen
+.next
.cindex "log" "outgoing interface"
.cindex "log" "local interface"
.cindex "log" "local address and port"
Signers SHOULD use RSA keys of at least 2048 bits.
.endd
-Support for EC keys is being developed under
-&url(https://datatracker.ietf.org/doc/draft-ietf-dcrup-dkim-crypto/).
+.new
+EC keys for DKIM are defined by RFC 8463.
+.wen
They are considerably smaller than RSA keys for equivalent protection.
As they are a recent development, users should consider dual-signing
(by setting a list of selectors, and an expansion for this option)
certtool --load_privkey=dkim_ed25519.private --pubkey_info --outder | tail -c +13 | base64
.endd
-Note that the format
-of Ed25519 keys in DNS has not yet been decided; this release supports
-both of the leading candidates at this time, a future release will
-probably drop support for whichever proposal loses.
+.new
+Exim also supports an alternate format
+of Ed25519 keys in DNS which was a candidate during development
+of the standard, but not adopted.
+A future release will probably drop that support.
+.wen
.option dkim_hash smtp string&!! sha256
Can be set to any one of the supported hash methods, which are:
git://git.exim.org / exim.git / blobdiff