and INCLUDE directives appropriately,
or set PCRE2_CONFIG=yes to use the installed &(pcre-config)& command.
If your operating system has no
-PCRE2 support then you will need to obtain and build the current PCRE
+PCRE2 support then you will need to obtain and build the current PCRE2
from &url(https://github.com/PhilipHazel/pcre2/releases).
More information on PCRE2 is available at &url(https://www.pcre.org/).
and a single key to search for. The key must be a non-empty string for the
lookup to succeed. The lookup type determines how the file is searched.
.cindex "tainted data" "single-key lookups"
-The file string may not be tainted
+The file string may not be tainted.
.cindex "tainted data" "de-tainting"
All single-key lookups support the option &"ret=key"&.
&*tls*&
Controls the use of TLS on the connection.
Values are &"yes"& or &"no"& (the default).
-If it is enabled, a shutdown as descripbed above is never done.
+If it is enabled, a shutdown as described above is never done.
.endlist
.cindex "&%pam%& expansion condition"
&'Pluggable Authentication Modules'&
(&url(https://mirrors.edge.kernel.org/pub/linux/libs/pam/)) are a facility that is
-available in the latest releases of Solaris and in some GNU/Linux
-distributions. The Exim support, which is intended for use in conjunction with
+available in Solaris
+and in some GNU/Linux distributions.
+The Exim support, which is intended for use in conjunction with
the SMTP AUTH command, is available only if Exim is compiled with
.code
SUPPORT_PAM=yes
.cindex "ESMTP extensions" DSN
DSN extensions (RFC3461) will be advertised in the EHLO message to,
and accepted from, these hosts.
-Hosts may use the NOTIFY and ENVID options on RCPT TO commands,
-and RET and ORCPT options on MAIL FROM commands.
+Hosts may use the NOTIFY and ORCPT options on RCPT TO commands,
+and RET and ENVID options on MAIL FROM commands.
A NOTIFY=SUCCESS option requests success-DSN messages.
A NOTIFY= option with no argument requests that no delay or failure DSNs
are sent.
The value of this option is expanded and indicates the source of DH parameters
to be used by Exim.
-This option is ignored for GnuTLS version 3.6.0 and later.
-The library manages parameter negotiation internally.
-
-&*Note: The Exim Maintainers strongly recommend,
-for other TLS library versions,
-using a filename with site-generated
+&*Note: The Exim Maintainers strongly recommend using a filename with site-generated
local DH parameters*&, which has been supported across all versions of Exim. The
other specific constants available are a fallback so that even when
"unconfigured", Exim can offer Perfect Forward Secrecy in older ciphersuites in TLS.
(the "ffdhe" identifiers).
At this point, all of the "ike" values should be considered obsolete;
-they're still in Exim to avoid breaking unusual configurations, but are
+they are still in Exim to avoid breaking unusual configurations, but are
candidates for removal the next time we have backwards-incompatible changes.
+.new
+Two of them in particular (&`ike1`& and &`ike22`&) are called out by RFC 8247
+as MUST NOT use for IPSEC, and two more (&`ike23`& and &`ike24`&) as
+SHOULD NOT.
+Because of this, Exim regards them as deprecated; if either of the first pair
+are used, warnings will be logged in the paniclog, and if any are used then
+warnings will be logged in the mainlog.
+All four will be removed in a future Exim release.
+.wen
The TLS protocol does not negotiate an acceptable size for this; clients tend
to hard-drop connections if what is offered by the server is unacceptable,
the message override the banner message that is otherwise specified by the
&%smtp_banner%& option.
+.new
+For tls-on-connect connections, the ACL is run after the TLS connection
+is accepted (however, &%host_reject_connection%& is tested before).
+.wen
+
.section "The EHLO/HELO ACL" "SECID192"
.cindex "EHLO" "ACL for"
.code
exim_dumpdb /var/spool/exim retry
.endd
-Two lines of output are produced for each entry:
+For the retry database
+two lines of output are produced for each entry:
.code
T:mail.ref.example:192.168.242.242 146 77 Connection refused
31-Oct-1995 12:00:12 02-Nov-1995 12:21:39 02-Nov-1995 20:21:39 *
The name is placed in the variable &$event_name$& and the event action
expansion must check this, as it will be called for every possible event type.
+.new
The current list of events is:
.display
&`dane:fail after transport `& per connection
&`tcp:connect before transport `& per connection
&`tcp:close after transport `& per connection
&`tls:cert before both `& per certificate in verification chain
+&`tls:fail:connect after main `& per connection
&`smtp:connect after transport `& per connection
&`smtp:ehlo after transport `& per connection
.endd
+.wen
New event types may be added in future.
The event name is a colon-separated list, defining the type of
&`msg:rcpt:host:defer `& error string
&`msg:rcpt:defer `& error string
&`tls:cert `& verification chain depth
+&`tls:fail:connect `& error string
&`smtp:connect `& smtp banner
&`smtp:ehlo `& smtp ehlo response
.endd
git://git.exim.org / exim.git / blobdiff