SMTP protocol names (see the description of &$received_protocol$& in section
&<<SECTexpvar>>&). For &%-bs%&, the protocol is always &"local-"& followed by
one of those same names. For &%-bS%& (batched SMTP) however, the protocol can
-be set by &%-oMr%&.
+be set by &%-oMr%&. Repeated use of this option is not supported.
.vitem &%-oMs%&&~<&'host&~name'&>
.oindex "&%-oMs%&"
Note the Exim already has two private options, &%-pd%& and &%-ps%&, that refer
to embedded Perl. It is therefore impossible to set a protocol value of &`d`&
or &`s`& using this option (but that does not seem a real limitation).
+Repeated use of this option is not supported.
.vitem &%-q%&
.oindex "&%-q%&"
space removed. Following the introduction of &$smtp_command$&, this variable is
somewhat redundant, but is retained for backwards compatibility.
+.new
+.vitem &$smtp_command_history$&
+.cindex SMTP "command history"
+.vindex "&$smtp_command_history$&"
+A comma-separated list (with no whitespace) of the most-recent SMTP commands
+received, in time-order left to right. Only a limited number of commands
+are remembered.
+.wen
+
.vitem &$smtp_count_at_connection_start$&
.vindex "&$smtp_count_at_connection_start$&"
This variable is set greater than zero only in processes spawned by the Exim
lookup first. Only if that gives a definite &"no such host"& is the local
function called.
+&*Compatibility*&: From Exim 4.85 until fixed for 4.90, there was an
+inadvertent constraint that a transport name as an option had to be the last
+option specified.
+
If no IP address for a host can be found, what happens is controlled by the
The value of the option is expanded, and must then be a numerical value
(decimal point allowed), optionally followed by one of the letters K, M, or G,
-for kilobytes, megabytes, or gigabytes. If Exim is running on a system with
+for kilobytes, megabytes, or gigabytes, optionally followed by a slash
+and further option modifiers. If Exim is running on a system with
large file support (Linux and FreeBSD have this), mailboxes larger than 2G can
be handled.
+The option modifier &%no_check%& can be used to force delivery even if the over
+quota condition is met. The quota gets updated as usual.
+
&*Note*&: A value of zero is interpreted as &"no quota"&.
The expansion happens while Exim is running as root, before it changes uid for
failure causes delivery to be deferred. A value of zero is interpreted as
&"no quota"&.
+The option modifier &%no_check%& can be used to force delivery even if the over
+quota condition is met. The quota gets updated as usual.
.option quota_is_inclusive appendfile boolean true
See &%quota%& above.
.new
Note that surrounding whitespace is stripped from each option, meaning
there is no way to specify a trailing newline.
+The socket specifier and both regular-expressions are required.
+Default for the commandline is &_%s\n_& (note this does have a trailing newline);
+specify an empty element to get this.
.wen
-Default for the socket specifier is &_/tmp/malware.sock_&.
-Default for the commandline is &_%s\n_& (note this does have a trailing newline).
-Both regular-expressions are required.
.vitem &%sophie%&
.cindex "virus scanners" "Sophos and Sophie"
&` incoming_interface `& local interface on <= and => lines
&` incoming_port `& remote port on <= lines
&`*lost_incoming_connection `& as it says (includes timeouts)
+&` millisec `& millisecond timestamps and QT/DT times
&` outgoing_interface `& local interface on => lines
&` outgoing_port `& add remote port to => lines
&`*queue_run `& start and end queue runs
.cindex "log" "delivery duration"
&%deliver_time%&: For each delivery, the amount of real time it has taken to
perform the actual delivery is logged as DT=<&'time'&>, for example, &`DT=1s`&.
+If millisecond logging is enabled, short times will be shown with greater
+precision, eg. &`DT=0.304`&.
.next
.cindex "log" "message size on delivery"
.cindex "size" "of message"
&%lost_incoming_connection%&: A log line is written when an incoming SMTP
connection is unexpectedly dropped.
.next
+.new
+.cindex "log" "millisecond timestamps"
+.cindex millisecond logging
+.cindex timstamps "millisecond, in logs"
+&%millisec%&: Timestamps have a period and three decimal places of finer granularity
+appended to the seconds value.
+.wen
+.next
.cindex "log" "outgoing interface"
.cindex "log" "local interface"
.cindex "log" "local address and port"
This means that it may be longer than the difference between the arrival and
delivery log line times, because the arrival log line is not written until the
message has been successfully received.
+If millisecond logging is enabled, short times will be shown with greater
+precision, eg. &`QT=1.578s`&.
.next
&%queue_time_overall%&: The amount of time the message has been in the queue on
the local host is logged as QT=<&'time'&> on &"Completed"& lines, for
.vitem &%$dkim_canon_body%&
The body canonicalization method. One of 'relaxed' or 'simple'.
-.vitem &%dkim_canon_headers%&
+.vitem &%$dkim_canon_headers%&
The header canonicalization method. One of 'relaxed' or 'simple'.
.vitem &%$dkim_copiedheaders%&
git://git.exim.org / exim.git / blobdiff