.cindex "incorporated code"
.cindex "regular expressions" "library"
.cindex "PCRE"
+.cindex "OpenDMARC"
A number of pieces of external code are included in the Exim distribution.
.ilist
SOFTWARE.
.endblockquote
+.next
+.cindex "opendmarc" "acknowledgment"
+The DMARC implementation uses the OpenDMARC library which is Copyrighted by
+The Trusted Domain Project. Portions of Exim source which use OpenDMARC
+derived code are indicated in the respective source files. The full OpenDMARC
+license is provided in the LICENSE.opendmarc file contained in the distributed
+source code.
+
.next
Many people have contributed code fragments, some large, some small, that were
not covered by any specific licence requirements. It is assumed that the
It sets the incoming protocol and host name (for trusted callers). The
host name and its colon can be omitted when only the protocol is to be set.
Note the Exim already has two private options, &%-pd%& and &%-ps%&, that refer
-to embedded Perl. It is therefore impossible to set a protocol value of &`p`&
+to embedded Perl. It is therefore impossible to set a protocol value of &`d`&
or &`s`& using this option (but that does not seem a real limitation).
.vitem &%-q%&
See &<<SECTtlssni>>& for discussion of when this option might be re-expanded.
+A forced expansion failure or setting to an empty string is equivalent to
+being unset.
+
.option tls_verify_hosts main "host list&!!" unset
.cindex "TLS" "client certificate verification"
option is not working properly, &%debug_print%& could be used to output the
variables it references. A newline is added to the text if it does not end with
one.
-The variables &$transport_name$ and &$router_name$& contain the name of the
+The variables &$transport_name$& and &$router_name$& contain the name of the
transport and the router that called it.
.vindex "&$address_pipe$&"
A router redirects an address directly to a pipe command (for example, from an
alias or forward file). In this case, &$address_pipe$& contains the text of the
-pipe command, and the &%command%& option on the transport is ignored. If only
-one address is being transported (&%batch_max%& is not greater than one, or
-only one address was redirected to this pipe command), &$local_part$& contains
-the local part that was redirected.
+pipe command, and the &%command%& option on the transport is ignored unless
+&%force_command%& is set. If only one address is being transported
+(&%batch_max%& is not greater than one, or only one address was redirected to
+this pipe command), &$local_part$& contains the local part that was redirected.
.endlist
avoids any problems with spaces or shell metacharacters, and is of use when a
&(pipe)& transport is handling groups of addresses in a batch.
+If &%force_command%& is enabled on the transport, Special handling takes place
+for an argument that consists of precisely the text &`$address_pipe`&. It
+is handled similarly to &$pipe_addresses$& above. It is expanded and each
+argument is inserted in the argument list at that point
+&'as a separate argument'&. The &`$address_pipe`& item does not need to be
+the only item in the argument; in fact, if it were then &%force_command%&
+should behave as a no-op. Rather, it should be used to adjust the command
+run while preserving the argument vector separation.
+
After splitting up into arguments and expansion, the resulting command is run
in a subprocess directly from the transport, &'not'& under a shell. The
message that is being delivered is supplied on the standard input, and the
frozen in Exim's queue instead.
+.option force_command pipe boolean false
+.cindex "force command"
+.cindex "&(pipe)& transport", "force command"
+Normally when a router redirects an address directly to a pipe command
+the &%command%& option on the transport is ignored. If &%force_command%&
+is set, the &%command%& option will used. This is especially
+useful for forcing a wrapper or additional argument to be added to the
+command. For example:
+.code
+command = /usr/bin/remote_exec myhost -- $address_pipe
+force_command
+.endd
+
+Note that &$address_pipe$& is handled specially in &%command%& when
+&%force_command%& is set, expanding out to the original argument vector as
+separate items, similarly to a Unix shell &`"$@"`& construct.
+
.option ignore_status pipe boolean false
If this option is true, the status returned by the subprocess that is set up to
run the command is ignored, and Exim behaves as if zero had been returned.
git://git.exim.org / exim.git / blobdiff