will need to be aware of the potential different format.
Using any of the ACL conditions noted will negate the reception benefit
-(as a Unix-mbox-format file is contructed for them).
-The transimssion benefit is maintained.
+(as a Unix-mbox-format file is constructed for them).
+The transmission benefit is maintained.
.option sqlite_lock_timeout main time 5s
.cindex "sqlite lookup type" "lock timeout"
separator in the usual way to avoid confusion under IPv6.
&*Note*&: Under current versions of OpenSSL, when a list of more than one
-file is used, the &$tls_in_ourcert$& veriable is unreliable.
+file is used, the &$tls_in_ourcert$& variable is unreliable.
&*Note*&: OCSP stapling is not usable under OpenSSL
when a list of more than one file is used.
On (at least some) current Linux distributions the facility must be enabled
in the kernel by the sysadmin before the support is usable.
There is no option for control of the server side; if the system supports
-it it is always enebled. Note that legthy operations in the connect ACL,
+it it is always enabled. Note that lengthy operations in the connect ACL,
such as DNSBL lookups, will still delay the emission of the SMTP banner.
.option hosts_try_prdr smtp "host list&!!" *
When Exim has been built with TLS support, it advertises the availability of
the STARTTLS command to client hosts that match &%tls_advertise_hosts%&,
but not to any others. The default value of this option is *, which means
-that STARTTLS is alway advertised. Set it to blank to never advertise;
-this is reasonble for systems that want to use TLS only as a client.
+that STARTTLS is always advertised. Set it to blank to never advertise;
+this is reasonable for systems that want to use TLS only as a client.
If STARTTLS is to be used you
need to set some other options in order to make TLS available.
An older mode of operation can be enabled on a per-host basis by the
&%hosts_noproxy_tls%& option on the &(smtp)& transport. If the host matches
-this list the proxy process descibed above is not used; instead Exim
+this list the proxy process described above is not used; instead Exim
shuts down an existing TLS session being run by the delivery process
before passing the socket to a new process. The new process may then
try to start a new TLS session, and if successful, may try to re-authenticate
.code
require verify = recipient/callout=use_sender,hold
.endd
-It causes the connection to be helod open and used for any further recipients
+It causes the connection to be held open and used for any further recipients
and for eventual delivery (should that be done quickly).
Doing this saves on TCP and SMTP startup costs, and TLS costs also
when that is used for the connections.
As an example, the following will ban &"HTML mail"& (including that sent with
alternative plain text), while allowing HTML files to be attached. HTML
-coverletter mail attached to non-HMTL coverletter mail will also be allowed:
+coverletter mail attached to non-HTML coverletter mail will also be allowed:
.code
deny message = HTML mail is not accepted here
!condition = $mime_is_rfc822
.new
.cindex log "DKIM verification"
.cindex DKIM "verification logging"
-&%dkim%&: For message acceptance log lines, when an DKIM signture in the header
+&%dkim%&: For message acceptance log lines, when an DKIM signature in the header
verifies successfully a tag of DKIM is added, with one of the verified domains.
.next
.cindex log "DKIM verification"
.next
.cindex "log" "millisecond timestamps"
.cindex millisecond logging
-.cindex timstamps "millisecond, in logs"
+.cindex timestamps "millisecond, in logs"
&%millisec%&: Timestamps have a period and three decimal places of finer granularity
appended to the seconds value.
.next
off the &%outgoing_interface%& option.
.next
.cindex "log" "outgoing remote port"
-.cindex "port" "logging outgoint remote"
+.cindex "port" "logging outgoing remote"
.cindex "TCP/IP" "logging outgoing remote port"
&%outgoing_port%&: The remote port number is added to delivery log lines (those
containing => tags) following the IP address.
The default list is available for the expansion in the macro
"_DKIM_SIGN_HEADERS".
-If a name is repeated, multiple headers by that name (or the absence therof)
+If a name is repeated, multiple headers by that name (or the absence thereof)
will be signed. The textually later headers in the headers part of the
message are signed first, if there are multiples.
If an '=' prefix is used, all headers that are present with this name
will be signed.
If a '+' prefix if used, all headers that are present with this name
-will be signed, and one signtature added for a missing header with the
+will be signed, and one signature added for a missing header with the
name will be appended.
or &%headers_charset%& main configuration option (otherwise),
to the
modified UTF-7 encoding specified by RFC 2060,
-with the following exception: All occurences of <sep>
+with the following exception: All occurrences of <sep>
(which has to be a single character)
are replaced with periods ("."), and all periods and slashes that are not
<sep> and are not in the <specials> string are BASE64 encoded.
before or after the action is associates with. Those which fire before
can be used to affect that action (more on this below).
-The third column in the table above says what section of the configumration
+The third column in the table above says what section of the configuration
should define the event action.
An additional variable, &$event_data$&, is filled with information varying
git://git.exim.org / exim.git / blobdiff