-$Cambridge: exim/doc/doc-txt/NewStuff,v 1.90 2006/02/23 12:41:22 ph10 Exp $
+$Cambridge: exim/doc/doc-txt/NewStuff,v 1.107 2006/07/21 16:48:42 jetmore Exp $
New Features in Exim
--------------------
updated when there is a relatively large batch of changes). The doc/ChangeLog
file contains a listing of all changes, including bug fixes.
+Version 4.63
+------------
+
+1. There is a new Boolean option called filter_prepend_home for the redirect
+ router. It defaults true, for backward compatibility. If a "save" command in
+ an Exim filter has a relative path for its argument, and $home is defined,
+ it is automatically prepended to the relative path. This action can now be
+ prevented by setting filter_prepend_home false.
+
+2. There is a new acl, set by acl_not_smtp_start, which is run right at the
+ start of receiving a non-SMTP message, before any of the message has been
+ read. (This is the analogue of the acl_smtp_predata ACL for SMTP input.) The
+ result of this ACL is ignored; it cannot be used to reject a message. If
+ you really need to, you could set a value in an ACL variable here and reject
+ based on that in the acl_not_smtp ACL. However, this ACL can be used to set
+ controls, and in particular, it can be used to set control=suppress_local_
+ fixups, which cannot be used in the acl_not_smtp ACL because by the time
+ that ACL is run, it is too late. When the acl_not_smtp_start ACL is run, the
+ sender and recipients are known, so the "senders" and "sender_domains"
+ conditions and $sender_address and $recipients variables can be used.
+ Variables such as $authenticated_ sender are also available. It is possible
+ to specify added header lines in this ACL.
+
+3. When an SMTP error message is specified in a "message" modifier in an ACL,
+ or in a :fail: or :defer: message in a redirect router, Exim now checks the
+ start of the message for an SMTP error code. This consists of three digits
+ followed by a space, optionally followed by an extended code of the form
+ n.n.n, also followed by a space. If this is the case and the very first
+ digit is the same as the default error code, the code from the message is
+ used instead. If the very first digit is incorrect, a panic error is logged,
+ and the default code is used. This is an incompatible change, but it is not
+ expected to affect many (if any) configurations. It is possible to suppress
+ the use of the supplied code in a redirect router by setting the
+ smtp_error_code option false. In this case, any SMTP code is quietly
+ ignored.
+
+4. There is a new parameter for LDAP lookups called "referrals", which takes
+ one of the settings "follow" (the default) or "nofollow". The latter stops
+ the LDAP library from trying to follow referrals issued by the LDAP server.
+
+5. Version 20070721.2 of exipick now included, offering these new options:
+ --reverse
+ After all other sorting options have bee processed, reverse order
+ before displaying messages (-R is synonym).
+ --random
+ Randomize order of matching messages before displaying.
+ --size
+ Instead of displaying the matching messages, display the sum
+ of their sizes.
+ --sort <variable>[,<variable>...]
+ Before displaying matching messages, sort the messages according to
+ each messages value for each variable.
+ --not
+ Negate the value for every test (returns inverse output from the
+ same criteria without --not).
+
+
+Version 4.62
+------------
+
+1. The ${readsocket expansion item now supports Internet domain sockets as well
+ as Unix domain sockets. If the first argument begins "inet:", it must be of
+ the form "inet:host:port". The port is mandatory; it may be a number or the
+ name of a TCP port in /etc/services. The host may be a name, or it may be an
+ IP address. An ip address may optionally be enclosed in square brackets.
+ This is best for IPv6 addresses. For example:
+
+ ${readsocket{inet:[::1]:1234}{<request data>}...
+
+ Only a single host name may be given, but if looking it up yield more than
+ one IP address, they are each tried in turn until a connection is made. Once
+ a connection has been made, the behaviour is as for ${readsocket with a Unix
+ domain socket.
+
+2. If a redirect router sets up file or pipe deliveries for more than one
+ incoming address, and the relevant transport has batch_max set greater than
+ one, a batch delivery now occurs.
+
+3. The appendfile transport has a new option called maildirfolder_create_regex.
+ Its value is a regular expression. For a maildir delivery, this is matched
+ against the maildir directory; if it matches, Exim ensures that a
+ maildirfolder file is created alongside the new, cur, and tmp directories.
+
+
Version 4.61
------------
-PH/01 There is a new global option called disable_ipv6, which does exactly what
- its name implies. If set true, even if the Exim binary has IPv6 support,
- no IPv6 activities take place. AAAA records are never looked up for host
- names given in manual routing data or elsewhere. AAAA records that are
- received from the DNS as additional data for MX records are ignored. Any
- IPv6 addresses that are listed in local_interfaces, manualroute route
- data, etc. are also ignored. If IP literals are enabled, the ipliteral
- router declines to handle IPv6 literal addresses.
-
-PH/02 There are now 20 of each type of ACL variable by default (instead of 10).
- It is also possible to change the numbers by setting ACL_CVARS and/or
- ACL_MVARS in Local/Makefile. Backward compatibility is maintained if you
- upgrade to this release with existing messages containing ACL variable
- settings on the queue. However, going in the other direction
- (downgrading) will not be compatible; the values of ACL variables will be
- lost.
-
-PH/03 If quota_warn_message contains a From: header, Exim now refrains from
- adding the default one. Similarly, if it contains a Reply-To: header, the
- errors_reply_to option, if set, is not used.
-
-PH/04 The variables $auth1, $auth2, $auth3 are now available in authenticators,
- containing the same values as $1, $2, $3. The new variables are provided
- because the numerical variables can be reset during string expansions
- (for example, during a "match" operation) and so may lose the
- authentication data. The preferred variables are now the new ones, with
- the use of the numerical ones being deprecated, though the support will
- not be removed, at least, not for a long time.
-
-PH/05 The "control=freeze" ACL modifier can now be followed by /no_tell. If
- the global option freeze_tell is set, it is ignored for the current
- message (that is, nobody is told about the freezing), provided all the
- "control=freeze" modifiers that are obeyed in the current message have
- the /no_tell option.
-
-PH/06 In both GnuTLS and OpenSSL, an expansion of tls_privatekey that results
- in an empty string is now treated as unset.
-
-PH/07 There is a new log selector called sender_verify_fail, which is set by
- default. If it is unset, the separate log line that gives details of a
- sender verification failure is not written. Log lines for the rejection
- of SMTP commands (e.g. RCPT) contain just "sender verify failed", so some
- detail is lost.
-
-PH/08 The default for dns_check_names_pattern now allows slashes within names,
- as there are now some PTR records that contain slashes. This check is
- only to protect against broken name servers that fall over on strange
- characters, so the fact that it applies to all lookups doesn't matter.
-
-PH/09 The default for rfc4131_query_timeout has been changed from 30s to 5s.
-
-PH/10 When compiled on FreeBSD, NetBSD, or BSD/OS, the pipe transport has a new
- Boolean option called use_classresources, defaulting false. If it is set
- true, the setclassresources() function is used to set resource limits
- when a pipe transport is run to perform a delivery. The limits for the
- uid under which the pipe is to run are obtained from the login class
- database.
-
-PH/11 If retry_interval_max is set greater than 24 hours, it is quietly reset
- to 24 hours. This avoids potential overflow problems when processing G
- and H retry rules, and it seems reasonable to require a retry at least
- once a day.
-
-PH/12 When the plaintext authenticator is running as a client, the server
- challenges are now checked to ensure they are valid base64 strings. The
- default action on failure is to abort the authentication. However, if
- client_ignore_invalid_base64 is set true, invalid responses are ignored.
-
-PH/13 When the plaintext authenticator is running as a client, the challenges
- from the server are placed in $auth1, $auth2, etc. as they are received.
- Thus, the challege that is received in response to sending the first
- string (with the AUTH command) can be used in the expansion of the second
- string, and so on. Currently, up to 3 challenge strings are available in
- this way. If an invalid base64 string is received when client_ignore_
- invalid_base64 is set, an empty string is put in the $auth<n> variable.
+The documentation is up-to-date for the 4.61 release. Major new features since
+the 4.60 release are:
+
+. An option called disable_ipv6, to disable the use of IPv6 completely.
+
+. An increase in the number of ACL variables to 20 of each type.
+
+. A change to use $auth1, $auth2, and $auth3 in authenticators instead of $1,
+ $2, $3, (though those are still set) because the numeric variables get used
+ for other things in complicated expansions.
+
+. The default for rfc1413_query_timeout has been changed from 30s to 5s.
+
+. It is possible to use setclassresources() on some BSD OS to control the
+ resources used in pipe deliveries.
+
+. A new ACL modifier called add_header, which can be used with any verb.
+
+. More errors are detectable in retry rules.
+
+There are a number of other additions too.
Version 4.60
git://git.exim.org / exim.git / blobdiff