-Sender Policy Framework (SPF) support
---------------------------------------------------------------
-
-To learn more about SPF, visit http://www.openspf.org. This
-document does not explain the SPF fundamentals, you should
-read and understand the implications of deploying SPF on your
-system before doing so.
-
-SPF support is added via the libspf2 library. Visit
-
- http://www.libspf2.org/
-
-to obtain a copy, then compile and install it. By default,
-this will put headers in /usr/local/include and the static
-library in /usr/local/lib.
-
-To compile Exim with SPF support, set these additional flags in
-Local/Makefile:
-
-EXPERIMENTAL_SPF=yes
-CFLAGS=-DSPF -I/usr/local/include
-EXTRALIBS_EXIM=-L/usr/local/lib -lspf2
-
-This assumes that the libspf2 files are installed in
-their default locations.
-
-You can now run SPF checks in incoming SMTP by using the "spf"
-ACL condition in either the MAIL, RCPT or DATA ACLs. When
-using it in the RCPT ACL, you can make the checks dependent on
-the RCPT address (or domain), so you can check SPF records
-only for certain target domains. This gives you the
-possibility to opt-out certain customers that do not want
-their mail to be subject to SPF checking.
-
-The spf condition takes a list of strings on its right-hand
-side. These strings describe the outcome of the SPF check for
-which the spf condition should succeed. Valid strings are:
-
- o pass The SPF check passed, the sending host
- is positively verified by SPF.
- o fail The SPF check failed, the sending host
- is NOT allowed to send mail for the domain
- in the envelope-from address.
- o softfail The SPF check failed, but the queried
- domain can't absolutely confirm that this
- is a forgery.
- o none The queried domain does not publish SPF
- records.
- o neutral The SPF check returned a "neutral" state.
- This means the queried domain has published
- a SPF record, but wants to allow outside
- servers to send mail under its domain as well.
- This should be treated like "none".
- o permerror This indicates a syntax error in the SPF
- record of the queried domain. You may deny
- messages when this occurs. (Changed in 4.83)
- o temperror This indicates a temporary error during all
- processing, including Exim's SPF processing.
- You may defer messages when this occurs.
- (Changed in 4.83)
- o err_temp Same as permerror, deprecated in 4.83, will be
- removed in a future release.
- o err_perm Same as temperror, deprecated in 4.83, will be
- removed in a future release.
-
-You can prefix each string with an exclamation mark to invert
-its meaning, for example "!fail" will match all results but
-"fail". The string list is evaluated left-to-right, in a
-short-circuit fashion. When a string matches the outcome of
-the SPF check, the condition succeeds. If none of the listed
-strings matches the outcome of the SPF check, the condition
-fails.
-
-Here is an example to fail forgery attempts from domains that
-publish SPF records:
-
-/* -----------------
-deny message = $sender_host_address is not allowed to send mail from ${if def:sender_address_domain {$sender_address_domain}{$sender_helo_name}}. \
- Please see http://www.openspf.org/Why?scope=${if def:sender_address_domain {mfrom}{helo}};identity=${if def:sender_address_domain {$sender_address}{$sender_helo_name}};ip=$sender_host_address
- spf = fail
---------------------- */
-
-You can also give special treatment to specific domains:
-
-/* -----------------
-deny message = AOL sender, but not from AOL-approved relay.
- sender_domains = aol.com
- spf = fail:neutral
---------------------- */
-
-Explanation: AOL publishes SPF records, but is liberal and
-still allows non-approved relays to send mail from aol.com.
-This will result in a "neutral" state, while mail from genuine
-AOL servers will result in "pass". The example above takes
-this into account and treats "neutral" like "fail", but only
-for aol.com. Please note that this violates the SPF draft.
-
-When the spf condition has run, it sets up several expansion
-variables.
-
- $spf_header_comment
- This contains a human-readable string describing the outcome
- of the SPF check. You can add it to a custom header or use
- it for logging purposes.
-
- $spf_received
- This contains a complete Received-SPF: header that can be
- added to the message. Please note that according to the SPF
- draft, this header must be added at the top of the header
- list. Please see section 10 on how you can do this.
-
- Note: in case of "Best-guess" (see below), the convention is
- to put this string in a header called X-SPF-Guess: instead.
-
- $spf_result
- This contains the outcome of the SPF check in string form,
- one of pass, fail, softfail, none, neutral, permerror or
- temperror.
-
- $spf_smtp_comment
- This contains a string that can be used in a SMTP response
- to the calling party. Useful for "fail".
-
-In addition to SPF, you can also perform checks for so-called
-"Best-guess". Strictly speaking, "Best-guess" is not standard
-SPF, but it is supported by the same framework that enables SPF
-capability. Refer to http://www.openspf.org/FAQ/Best_guess_record
-for a description of what it means.
-
-To access this feature, simply use the spf_guess condition in place
-of the spf one. For example:
-
-/* -----------------
-deny message = $sender_host_address doesn't look trustworthy to me
- spf_guess = fail
---------------------- */
-
-In case you decide to reject messages based on this check, you
-should note that although it uses the same framework, "Best-guess"
-is NOT SPF, and therefore you should not mention SPF at all in your
-reject message.
-
-When the spf_guess condition has run, it sets up the same expansion
-variables as when spf condition is run, described above.
-
-Additionally, since Best-guess is not standardized, you may redefine
-what "Best-guess" means to you by redefining spf_guess variable in
-global config. For example, the following:
-
-/* -----------------
-spf_guess = v=spf1 a/16 mx/16 ptr ?all
---------------------- */
-
-would relax host matching rules to a broader network range.
-
-
-A lookup expansion is also available. It takes an email
-address as the key and an IP address as the database:
-
- $lookup (username@domain} spf {ip.ip.ip.ip}}
-
-The lookup will return the same result strings as they can appear in
-$spf_result (pass,fail,softfail,neutral,none,err_perm,err_temp).
-Currently, only IPv4 addresses are supported.
-
-
-
git://git.exim.org / exim.git / blobdiff