Merge branch 'ocsp_staple_rollup'

[exim.git] / doc / doc-docbook / spec.xfpt

diff --git a/doc/doc-docbook/spec.xfpt b/doc/doc-docbook/spec.xfpt
index 92d0a22879211a7b191de4e1d15406cdd04b08c1..063d74a9290ed79e066af496c627561767828932 100644 (file)
--- a/doc/doc-docbook/spec.xfpt
+++ b/doc/doc-docbook/spec.xfpt
@@ -4335,7 +4335,7 @@ For compatibility with Sendmail, this option is equivalent to
 It sets the incoming protocol and host name (for trusted callers). The
 host name and its colon can be omitted when only the protocol is to be set.
 Note the Exim already has two private options, &%-pd%& and &%-ps%&, that refer
-to embedded Perl. It is therefore impossible to set a protocol value of &`p`&
+to embedded Perl. It is therefore impossible to set a protocol value of &`d`&
 or &`s`& using this option (but that does not seem a real limitation).
 
 .vitem &%-q%&
@@ -21601,10 +21601,10 @@ that are routed to the transport.
 .vindex "&$address_pipe$&"
 A router redirects an address directly to a pipe command (for example, from an
 alias or forward file). In this case, &$address_pipe$& contains the text of the
-pipe command, and the &%command%& option on the transport is ignored. If only
-one address is being transported (&%batch_max%& is not greater than one, or
-only one address was redirected to this pipe command), &$local_part$& contains
-the local part that was redirected.
+pipe command, and the &%command%& option on the transport is ignored unless
+&%force_command%& is set. If only one address is being transported
+(&%batch_max%& is not greater than one, or only one address was redirected to
+this pipe command), &$local_part$& contains the local part that was redirected.
 .endlist
 
 
@@ -21712,6 +21712,15 @@ inserted in the argument list at that point &'as a separate argument'&. This
 avoids any problems with spaces or shell metacharacters, and is of use when a
 &(pipe)& transport is handling groups of addresses in a batch.
 
+If &%force_command%& is enabled on the transport, Special handling takes place
+for an argument that consists of precisely the text &`$address_pipe`&.  It
+is handled similarly to &$pipe_addresses$& above.  It is expanded and each
+argument is inserted in the argument list at that point
+&'as a separate argument'&.  The &`$address_pipe`& item does not need to be
+the only item in the argument; in fact, if it were then &%force_command%&
+should behave as a no-op.  Rather, it should be used to adjust the command
+run while preserving the argument vector separation.
+
 After splitting up into arguments and expansion, the resulting command is run
 in a subprocess directly from the transport, &'not'& under a shell. The
 message that is being delivered is supplied on the standard input, and the
@@ -21864,6 +21873,23 @@ a bounce message is sent. If &%freeze_signal%& is set, the message will be
 frozen in Exim's queue instead.
 
 
+.option force_command pipe boolean false
+.cindex "force command"
+.cindex "&(pipe)& transport", "force command"
+Normally when a router redirects an address directly to a pipe command
+the &%command%& option on the transport is ignored.  If &%force_command%&
+is set, the &%command%& option will used. This is especially
+useful for forcing a wrapper or additional argument to be added to the
+command. For example:
+.code
+command = /usr/bin/remote_exec myhost -- $address_pipe
+force_command
+.endd
+
+Note that &$address_pipe$& is handled specially in &%command%& when
+&%force_command%& is set, expanding out to the original argument vector as
+separate items, similarly to a Unix shell &`"$@"`& construct.
+
 .option ignore_status pipe boolean false
 If this option is true, the status returned by the subprocess that is set up to
 run the command is ignored, and Exim behaves as if zero had been returned.