Docs: ETRN default command

[exim.git] / doc / doc-docbook / spec.xfpt

diff --git a/doc/doc-docbook/spec.xfpt b/doc/doc-docbook/spec.xfpt
index aed97644c4f650342d39624e76608dc99f248174..fbcad3d6ff1439503b2af5d3fe56c16190835fcf 100644 (file)
--- a/doc/doc-docbook/spec.xfpt
+++ b/doc/doc-docbook/spec.xfpt
@@ -17274,6 +17274,13 @@ example:
 smtp_etrn_command = /etc/etrn_command $domain \
                     $sender_host_address
 .endd
+.new
+If the option is not set, the argument for the ETRN command must
+be a &'#'& followed by an address string.
+In this case an &'exim -R <string>'& command is used;
+if the ETRN ACL has set up a named-queue then &'-MCG <queue>'& is appended.
+.wen
+
 A new process is created to run the command, but Exim does not wait for it to
 complete. Consequently, its status cannot be checked. If the command cannot be
 run, a line is written to the panic log, but the ETRN caller still receives
@@ -18655,8 +18662,10 @@ This option specifies a list of text headers,
 colon-separated (by default, changeable in the usual way &<<SECTlistsepchange>>&),
 that is associated with any addresses that are accepted by the router.
 However, the option has no effect when an address is just being verified.
-Each list item is separately expanded, at routing time.
-If an item ends in *, it will match any header with the same prefix.
+Each list item is separately expanded, at transport time.
+.new
+If an item ends in *, it will match any header with the given prefix.
+.wen
 The way in which
 the text is used to remove header lines at transport time is described in
 section &<<SECTheadersaddrem>>&. Header lines are not actually removed until
@@ -18664,7 +18673,7 @@ the message is in the process of being transported. This means that references
 to header lines in string expansions in the transport's configuration still
 &"see"& the original header lines.
 
-The &%headers_remove%& option is expanded after &%errors_to%& and
+The &%headers_remove%& option is handled after &%errors_to%& and
 &%headers_add%&, but before &%transport%&. If an item expansion is forced to fail,
 the item has no effect. Other expansion failures are treated as configuration
 errors.
@@ -21843,15 +21852,21 @@ checked, since this option does not automatically suppress them.
 .option headers_remove transports list&!! unset
 .cindex "header lines" "removing"
 .cindex "transport" "header lines; removing"
-This option specifies a list of header names,
-colon-separated (by default, changeable in the usual way &<<SECTlistsepchange>>&);
-these headers are omitted from the message as it is transported, as described
-in section &<<SECTheadersaddrem>>&. Header removal can also be specified by
-routers.
+This option specifies a list of text headers,
+colon-separated (by default, changeable in the usual way &<<SECTlistsepchange>>&),
+to be removed from the message.
+However, the option has no effect when an address is just being verified.
 Each list item is separately expanded.
 If the result of the expansion is an empty string, or if the expansion
 is forced to fail, no action is taken. Other expansion failures are treated as
 errors and cause the delivery to be deferred.
+.new
+If an item ends in *, it will match any header with the given prefix.
+.wen
+
+Matching headers are omitted from the message as it is transported, as described
+in section &<<SECTheadersaddrem>>&. Header removal can also be specified by
+routers.
 
 Unlike most options, &%headers_remove%& can be specified multiple times
 for a transport; all listed headers are removed.
@@ -30143,7 +30158,7 @@ in several different ways. For example:
 It can be at the end of an &%accept%& statement:
 .code
     accept  ...some conditions
-            control = queue_only
+            control = queue
 .endd
 In this case, the control is applied when this statement yields &"accept"&, in
 other words, when the conditions are all true.
@@ -30152,7 +30167,7 @@ other words, when the conditions are all true.
 It can be in the middle of an &%accept%& statement:
 .code
     accept  ...some conditions...
-            control = queue_only
+            control = queue
             ...some more conditions...
 .endd
 If the first set of conditions are true, the control is applied, even if the
@@ -33899,13 +33914,14 @@ in &_Local/Makefile_& (see section &<<SECTconoptloc>>& below).
 .cindex &%dlfunc%& "API description"
 You must include this line near the start of your code:
 .code
+#define LOCAL_SCAN
 #include "local_scan.h"
 .endd
 This header file defines a number of variables and other values, and the
 prototype for the function itself. Exim is coded to use unsigned char values
 almost exclusively, and one of the things this header defines is a shorthand
 for &`unsigned char`& called &`uschar`&.
-It also contains the following macro definitions, to simplify casting character
+It also makes available the following macro definitions, to simplify casting character
 strings and pointers to character strings:
 .code
 #define CS   (char *)