Test suite normalize TLS 1.[12] to TLS1

[exim.git] / doc / doc-docbook / spec.xfpt

diff --git a/doc/doc-docbook/spec.xfpt b/doc/doc-docbook/spec.xfpt
index 17bdcc943a6b3a2bc3a668a5a5fc8971a7a2efe4..cbe5c1851ad17da735b270c181c9b0ad4cb2bafe 100644 (file)
--- a/doc/doc-docbook/spec.xfpt
+++ b/doc/doc-docbook/spec.xfpt
@@ -52,7 +52,7 @@
 .set I   "    "
 
 .macro copyyear
 .set I   "    "
 
 .macro copyyear

-2013
+2014

 .endmacro
 
 . /////////////////////////////////////////////////////////////////////////////
 .endmacro
 
 . /////////////////////////////////////////////////////////////////////////////


@@ -4221,6 +4221,20 @@ option sets the IP interface address value. A port number may be included,
 using the same syntax as for &%-oMa%&. The interface address is placed in
 &$received_ip_address$& and the port number, if present, in &$received_port$&.
 
 using the same syntax as for &%-oMa%&. The interface address is placed in
 &$received_ip_address$& and the port number, if present, in &$received_port$&.
 

+.vitem &%-oMm%&&~<&'message&~reference'&>
+.oindex "&%-oMm%&"
+.cindex "message reference" "message reference, specifying for local message"
+See &%-oMa%& above for general remarks about the &%-oM%& options. The &%-oMm%&
+option sets the message reference, e.g. message-id, and is logged during
+delivery. This is useful when some kind of audit trail is required to tie
+messages together. The format of the message reference is checked and will
+abort if the format is invalid. The option will only be accepted if exim is
+running in trusted mode, not as any regular user.
+
+The best example of a message reference is when Exim sends a bounce message.
+The message reference is the message-id of the original message for which Exim
+is sending the bounce.
+

 .vitem &%-oMr%&&~<&'protocol&~name'&>
 .oindex "&%-oMr%&"
 .cindex "protocol, specifying for local message"
 .vitem &%-oMr%&&~<&'protocol&~name'&>
 .oindex "&%-oMr%&"
 .cindex "protocol, specifying for local message"


@@ -6840,7 +6854,7 @@ is used on its own as the result. If the lookup does not succeed, the
 &`fail`& keyword causes a &'forced expansion failure'& &-- see section
 &<<SECTforexpfai>>& for an explanation of what this means.
 
 &`fail`& keyword causes a &'forced expansion failure'& &-- see section
 &<<SECTforexpfai>>& for an explanation of what this means.
 

-The supported DNS record types are A, CNAME, MX, NS, PTR, SPF, SRV, and TXT,
+The supported DNS record types are A, CNAME, MX, NS, PTR, SPF, SRV, TLSA and TXT,

 and, when Exim is compiled with IPv6 support, AAAA (and A6 if that is also
 configured). If no type is given, TXT is assumed. When the type is PTR,
 the data can be an IP address, written as normal; inversion and the addition of
 and, when Exim is compiled with IPv6 support, AAAA (and A6 if that is also
 configured). If no type is given, TXT is assumed. When the type is PTR,
 the data can be an IP address, written as normal; inversion and the addition of


@@ -6959,11 +6973,16 @@ The data from each lookup is concatenated, with newline separators by default,
 in the same way that multiple DNS records for a single item are handled. A
 different separator can be specified, as described above.
 
 in the same way that multiple DNS records for a single item are handled. A
 different separator can be specified, as described above.
 

+Modifiers for &(dnsdb)& lookups are givien by optional keywords,
+each followed by a comma,
+that may appear before the record type.
+

 The &(dnsdb)& lookup fails only if all the DNS lookups fail. If there is a
 temporary DNS error for any of them, the behaviour is controlled by
 The &(dnsdb)& lookup fails only if all the DNS lookups fail. If there is a
 temporary DNS error for any of them, the behaviour is controlled by

-an optional keyword followed by a comma that may appear before the record
-type. The possible keywords are &"defer_strict"&, &"defer_never"&, and
-&"defer_lax"&. With &"strict"& behaviour, any temporary DNS error causes the
+a defer-option modifier.
+The possible keywords are
+&"defer_strict"&, &"defer_never"&, and &"defer_lax"&.
+With &"strict"& behaviour, any temporary DNS error causes the

 whole lookup to defer. With &"never"& behaviour, a temporary DNS error is
 ignored, and the behaviour is as if the DNS lookup failed to find anything.
 With &"lax"& behaviour, all the queries are attempted, but a temporary DNS
 whole lookup to defer. With &"never"& behaviour, a temporary DNS error is
 ignored, and the behaviour is as if the DNS lookup failed to find anything.
 With &"lax"& behaviour, all the queries are attempted, but a temporary DNS


@@ -6976,6 +6995,21 @@ ${lookup dnsdb{a=one.host.com:two.host.com}}
 Thus, in the default case, as long as at least one of the DNS lookups
 yields some data, the lookup succeeds.
 
 Thus, in the default case, as long as at least one of the DNS lookups
 yields some data, the lookup succeeds.
 

+.new
+.cindex "DNSSEC" "dns lookup"
+Use of &(DNSSEC)& is controlled by a dnssec modifier.
+The possible keywords are
+&"dnssec_strict"&, &"dnssec_lax"&, and &"dnssec_never"&.
+With &"strict"& or &"lax"& DNSSEC information is requested
+with the lookup.
+With &"strict"& a response from the DNS resolver that
+is not labelled as authenticated data
+is treated as equivalent to a temporary DNS error.
+The default is &"never"&.
+
+See also the &$lookup_dnssec_authenticated$& variable.
+.wen
+

 
 
 
 
 
 


@@ -7198,6 +7232,9 @@ them. The following names are recognized:
 &`USER       `&  set the DN, for authenticating the LDAP bind
 &`PASS       `&  set the password, likewise
 &`REFERRALS  `&  set the referrals parameter
 &`USER       `&  set the DN, for authenticating the LDAP bind
 &`PASS       `&  set the password, likewise
 &`REFERRALS  `&  set the referrals parameter

+.new
+&`SERVERS    `&  set alternate server list for this query only
+.wen

 &`SIZE       `&  set the limit for the number of entries returned
 &`TIME       `&  set the maximum waiting time for a query
 .endd
 &`SIZE       `&  set the limit for the number of entries returned
 &`TIME       `&  set the maximum waiting time for a query
 .endd


@@ -7219,6 +7256,15 @@ Netscape SDK; for OpenLDAP no action is taken.
 The TIME parameter (also a number of seconds) is passed to the server to
 set a server-side limit on the time taken to complete a search.
 
 The TIME parameter (also a number of seconds) is passed to the server to
 set a server-side limit on the time taken to complete a search.
 

+.new
+The SERVERS parameter allows you to specify an alternate list of ldap servers
+to use for an individual lookup.  The global ldap_servers option provides a
+default list of ldap servers, and a single lookup can specify a single ldap
+server to use.  But when you need to do a lookup with a list of servers that is
+different than the default list (maybe different order, maybe a completely
+different set of servers), the SERVERS parameter allows you to specify this
+alternate list.
+.wen

 
 Here is an example of an LDAP query in an Exim lookup that uses some of these
 values. This is a single line, folded to fit on the page:
 
 Here is an example of an LDAP query in an Exim lookup that uses some of these
 values. This is a single line, folded to fit on the page:


@@ -8298,7 +8344,14 @@ Both &`+include_unknown`& and &`+ignore_unknown`& may appear in the same
 list. The effect of each one lasts until the next, or until the end of the
 list.
 
 list. The effect of each one lasts until the next, or until the end of the
 list.
 

-To explain the host/ip processing logic a different way for the same ACL:
+.new
+.section "Mixing wildcarded host names and addresses in host lists" &&&
+         "SECTmixwilhos"
+.cindex "host list" "mixing names and addresses in"
+
+This section explains the host/ip processing logic with the same concepts
+as the previous section, but specifically addresses what happens when a
+wildcarded hostname is one of the items in the hostlist.

 
 .ilist
 If you have name lookups or wildcarded host names and
 
 .ilist
 If you have name lookups or wildcarded host names and


@@ -8327,7 +8380,7 @@ If the first &%accept%& fails, Exim goes on to try the second one. See chapter
 &`+ignore_unknown`&, which was discussed in depth in the first example in
 this section.
 .endlist
 &`+ignore_unknown`&, which was discussed in depth in the first example in
 this section.
 .endlist

-
+.wen

 
 
 .section "Temporary DNS errors when looking up host information" &&&
 
 
 .section "Temporary DNS errors when looking up host information" &&&


@@ -8399,33 +8452,6 @@ See section &<<SECThoslispatsikey>>&.)
 
 
 
 
 
 

-.section "Mixing wildcarded host names and addresses in host lists" &&&
-         "SECTmixwilhos"
-.cindex "host list" "mixing names and addresses in"
-If you have name lookups or wildcarded host names and IP addresses in the same
-host list, you should normally put the IP addresses first. For example, in an
-ACL you could have:
-.code
-accept hosts = 10.9.8.7 : *.friend.example
-.endd
-The reason for this lies in the left-to-right way that Exim processes lists.
-It can test IP addresses without doing any DNS lookups, but when it reaches an
-item that requires a host name, it fails if it cannot find a host name to
-compare with the pattern. If the above list is given in the opposite order, the
-&%accept%& statement fails for a host whose name cannot be found, even if its
-IP address is 10.9.8.7.
-
-If you really do want to do the name check first, and still recognize the IP
-address, you can rewrite the ACL like this:
-.code
-accept hosts = *.friend.example
-accept hosts = 10.9.8.7
-.endd
-If the first &%accept%& fails, Exim goes on to try the second one. See chapter
-&<<CHAPACL>>& for details of ACLs.
-
-
-

 
 
 .section "Address lists" "SECTaddresslist"
 
 
 .section "Address lists" "SECTaddresslist"


@@ -8849,6 +8875,55 @@ the expansion result is an empty string.
 If the ACL returns defer the result is a forced-fail.  Otherwise the expansion fails.
 
 
 If the ACL returns defer the result is a forced-fail.  Otherwise the expansion fails.
 
 

+.new
+.vitem "&*${certextract{*&<&'field'&>&*}{*&<&'certificate'&>&*}&&&
+       {*&<&'string2'&>&*}{*&<&'string3'&>&*}}*&"
+.cindex "expansion" "extracting cerificate fields"
+.cindex "&%certextract%&" "certificate fields"
+.cindex "certificate" "extracting fields"
+The <&'certificate'&> must be a variable of type certificate.
+The field name is expanded and used to retrive the relevant field from
+the certificate.  Supported fields are:
+.display
+&`version        `&
+&`serial_number  `&
+&`subject        `&
+&`issuer         `&
+&`notbefore      `&
+&`notafter       `&
+&`sig_algorithm  `&
+&`signature      `&
+&`subj_altname   `& tagged list
+&`ocsp_uri       `& list
+&`crl_uri        `& list
+.endd
+If the field is found,
+<&'string2'&> is expanded, and replaces the whole item;
+otherwise <&'string3'&> is used. During the expansion of <&'string2'&> the
+variable &$value$& contains the value that has been extracted. Afterwards, it
+is restored to any previous value it might have had.
+
+If {<&'string3'&>} is omitted, the item is replaced by an empty string if the
+key is not found. If {<&'string2'&>} is also omitted, the value that was
+extracted is used.
+
+Some field names take optional modifiers, appended and separated by commas.
+
+The field selectors marked as "list" above return a list,
+newline-separated by default,
+(embedded separator characters in elements are doubled).
+The separator may be changed by a modifier of
+a right angle-bracket followed immediately by the new separator.
+
+The field selectors marked as "tagged" above
+prefix each list element with a type string and an equals sign.
+Elements of only one type may be selected by a modifier
+which is one of "dns", "uri" or "mail";
+if so the elenment tags are omitted.
+
+Field values are generally presented in human-readable form.
+.wen
+

 .vitem "&*${dlfunc{*&<&'file'&>&*}{*&<&'function'&>&*}{*&<&'arg'&>&*}&&&
        {*&<&'arg'&>&*}...}*&"
 .cindex &%dlfunc%&
 .vitem "&*${dlfunc{*&<&'file'&>&*}{*&<&'function'&>&*}{*&<&'arg'&>&*}&&&
        {*&<&'arg'&>&*}...}*&"
 .cindex &%dlfunc%&


@@ -9181,6 +9256,44 @@ of <&'string2'&>, whichever is the shorter. Do not confuse &%length%& with
 &%strlen%&, which gives the length of a string.
 
 
 &%strlen%&, which gives the length of a string.
 
 

+.vitem "&*${listextract{*&<&'number'&>&*}&&&
+        {*&<&'string1'&>&*}{*&<&'string2'&>&*}{*&<&'string3'&>&*}}*&"
+.cindex "expansion" "extracting list elements by number"
+.cindex "&%listextract%&" "extract list elements by number"
+.cindex "list" "extracting elements by number"
+The <&'number'&> argument must consist entirely of decimal digits,
+apart from an optional leading minus,
+and leading and trailing white space (which is ignored).
+
+After expansion, <&'string1'&> is interpreted as a list, colon-separated by
+default, but the separator can be changed in the usual way.
+
+The first field of the list is numbered one.
+If the number is negative, the fields are
+counted from the end of the list, with the rightmost one numbered -1.
+The numbered element of the list is extracted and placed in &$value$&,
+then <&'string2'&> is expanded as the result.
+
+If the modulus of the
+number is zero or greater than the number of fields in the string,
+the result is the expansion of <&'string3'&>.
+
+For example:
+.code
+${listextract{2}{x:42:99}}
+.endd
+yields &"42"&, and
+.code
+${listextract{-3}{<, x,42,99,& Mailer,,/bin/bash}{result: $value}}
+.endd
+yields &"result: 99"&.
+
+If {<&'string3'&>} is omitted, an empty string is used for string3.
+If {<&'string2'&>} is also omitted, the value that was
+extracted is used.
+You can use &`fail`& instead of {<&'string3'&>} as in a string extract.
+
+

 .vitem "&*${lookup{*&<&'key'&>&*}&~*&<&'search&~type'&>&*&~&&&
         {*&<&'file'&>&*}&~{*&<&'string1'&>&*}&~{*&<&'string2'&>&*}}*&"
 This is the first of one of two different types of lookup item, which are both
 .vitem "&*${lookup{*&<&'key'&>&*}&~*&<&'search&~type'&>&*&~&&&
         {*&<&'file'&>&*}&~{*&<&'string1'&>&*}&~{*&<&'string2'&>&*}}*&"
 This is the first of one of two different types of lookup item, which are both


@@ -9923,6 +10036,7 @@ Letters in IPv6 addresses are always output in lower case.
 .vitem &*${md5:*&<&'string'&>&*}*&
 .cindex "MD5 hash"
 .cindex "expansion" "MD5 hash"
 .vitem &*${md5:*&<&'string'&>&*}*&
 .cindex "MD5 hash"
 .cindex "expansion" "MD5 hash"

+.cindex "certificate fingerprint"

 .cindex "&%md5%& expansion item"
 The &%md5%& operator computes the MD5 hash value of the string, and returns it
 as a 32-digit hexadecimal number, in which any letters are in lower case.
 .cindex "&%md5%& expansion item"
 The &%md5%& operator computes the MD5 hash value of the string, and returns it
 as a 32-digit hexadecimal number, in which any letters are in lower case.


@@ -10060,11 +10174,24 @@ variables or headers inside regular expressions.
 .vitem &*${sha1:*&<&'string'&>&*}*&
 .cindex "SHA-1 hash"
 .cindex "expansion" "SHA-1 hashing"
 .vitem &*${sha1:*&<&'string'&>&*}*&
 .cindex "SHA-1 hash"
 .cindex "expansion" "SHA-1 hashing"

+.cindex "certificate fingerprint"

 .cindex "&%sha2%& expansion item"
 The &%sha1%& operator computes the SHA-1 hash value of the string, and returns
 it as a 40-digit hexadecimal number, in which any letters are in upper case.
 
 
 .cindex "&%sha2%& expansion item"
 The &%sha1%& operator computes the SHA-1 hash value of the string, and returns
 it as a 40-digit hexadecimal number, in which any letters are in upper case.
 
 

+.vitem &*${sha256:*&<&'certificate'&>&*}*&
+.cindex "SHA-256 hash"
+.cindex "certificate fingerprint"
+.cindex "expansion" "SHA-256 hashing"
+.cindex "&%sha256%& expansion item"
+The &%sha256%& operator computes the SHA-256 hash fingerprint of the
+certificate,
+and returns
+it as a 64-digit hexadecimal number, in which any letters are in upper case.
+Only arguments which are a single variable of certificate type are supported.
+
+

 .vitem &*${stat:*&<&'string'&>&*}*&
 .cindex "expansion" "statting a file"
 .cindex "file" "extracting characteristics"
 .vitem &*${stat:*&<&'string'&>&*}*&
 .cindex "expansion" "statting a file"
 .cindex "file" "extracting characteristics"


@@ -10133,6 +10260,14 @@ number of larger units and output in Exim's normal time format, for example,
 .cindex "expansion" "case forcing"
 .cindex "&%uc%& expansion item"
 This forces the letters in the string into upper-case.
 .cindex "expansion" "case forcing"
 .cindex "&%uc%& expansion item"
 This forces the letters in the string into upper-case.

+
+.vitem &*${utf8clean:*&<&'string'&>&*}*&
+.cindex "correction of invalid utf-8 sequences in strings"
+.cindex "utf-8" "utf-8 sequences"
+.cindex "incorrect utf-8"
+.cindex "expansion" "utf-8 forcing"
+.cindex "&%utf8clean%& expansion item"
+This replaces any invalid utf-8 sequence in the string by the character &`?`&.

 .endlist
 
 
 .endlist
 
 


@@ -10201,7 +10336,7 @@ If the ACL returns defer the result is a forced-fail.
 .cindex "&%bool%& expansion condition"
 This condition turns a string holding a true or false representation into
 a boolean state.  It parses &"true"&, &"false"&, &"yes"& and &"no"&
 .cindex "&%bool%& expansion condition"
 This condition turns a string holding a true or false representation into
 a boolean state.  It parses &"true"&, &"false"&, &"yes"& and &"no"&

-(case-insensitively); also positive integer numbers map to true if non-zero,
+(case-insensitively); also integer numbers map to true if non-zero,

 false if zero.
 An empty string is treated as false.
 Leading and trailing whitespace is ignored;
 false if zero.
 An empty string is treated as false.
 Leading and trailing whitespace is ignored;


@@ -11395,6 +11530,16 @@ ability to find the amount of free space (only true for experimental systems),
 the space value is -1. See also the &%check_log_space%& option.
 
 
 the space value is -1. See also the &%check_log_space%& option.
 
 

+.new
+.vitem &$lookup_dnssec_authenticated$&
+.vindex "&$lookup_dnssec_authenticated$&"
+This variable is set after a DNS lookup done by
+a dnsdb lookup expansion, dnslookup router or smtp transport.
+It will be empty if &(DNSSEC)& was not requested,
+&"no"& if the result was not labelled as authenticated data
+and &"yes"& if it was.
+.wen
+

 .vitem &$mailstore_basename$&
 .vindex "&$mailstore_basename$&"
 This variable is set only when doing deliveries in &"mailstore"& format in the
 .vitem &$mailstore_basename$&
 .vindex "&$mailstore_basename$&"
 This variable is set only when doing deliveries in &"mailstore"& format in the


@@ -11940,7 +12085,7 @@ other times, this variable is false.
 It is likely that you will need to coerce DNSSEC support on in the resolver
 library, by setting:
 .code
 It is likely that you will need to coerce DNSSEC support on in the resolver
 library, by setting:
 .code

-dns_use_dnssec = 1
+dns_dnssec_ok = 1

 .endd
 
 Exim does not perform DNSSEC validation itself, instead leaving that to a
 .endd
 
 Exim does not perform DNSSEC validation itself, instead leaving that to a


@@ -12171,6 +12316,44 @@ on an outbound SMTP connection; the meaning of
 this depends upon the TLS implementation used.
 If TLS has not been negotiated, the value will be 0.
 
 this depends upon the TLS implementation used.
 If TLS has not been negotiated, the value will be 0.
 

+.new
+.vitem &$tls_in_ourcert$&
+.vindex "&$tls_in_ourcert$&"
+This variable refers to the certificate presented to the peer of an
+inbound connection when the message was received.
+It is only useful as the argument of a
+&%certextract%& expansion item, &%md5%& or &%sha1%& operator,
+or a &%def%& condition.
+.wen
+
+.new
+.vitem &$tls_in_peercert$&
+.vindex "&$tls_in_peercert$&"
+This variable refers to the certificate presented by the peer of an
+inbound connection when the message was received.
+It is only useful as the argument of a
+&%certextract%& expansion item, &%md5%& or &%sha1%& operator,
+or a &%def%& condition.
+.wen
+
+.new
+.vitem &$tls_out_ourcert$&
+.vindex "&$tls_out_ourcert$&"
+This variable refers to the certificate presented to the peer of an
+outbound connection.  It is only useful as the argument of a
+&%certextract%& expansion item, &%md5%& or &%sha1%& operator,
+or a &%def%& condition.
+.wen
+
+.new
+.vitem &$tls_out_peercert$&
+.vindex "&$tls_out_peercert$&"
+This variable refers to the certificate presented by the peer of an
+outbound connection.  It is only useful as the argument of a
+&%certextract%& expansion item, &%md5%& or &%sha1%& operator,
+or a &%def%& condition.
+.wen
+

 .vitem &$tls_in_certificate_verified$&
 .vindex "&$tls_in_certificate_verified$&"
 This variable is set to &"1"& if a TLS certificate was verified when the
 .vitem &$tls_in_certificate_verified$&
 .vindex "&$tls_in_certificate_verified$&"
 This variable is set to &"1"& if a TLS certificate was verified when the


@@ -13152,10 +13335,10 @@ See also the &'Policy controls'& section above.
 .row &%disable_ipv6%&                "do no IPv6 processing"
 .row &%dns_again_means_nonexist%&    "for broken domains"
 .row &%dns_check_names_pattern%&     "pre-DNS syntax check"
 .row &%disable_ipv6%&                "do no IPv6 processing"
 .row &%dns_again_means_nonexist%&    "for broken domains"
 .row &%dns_check_names_pattern%&     "pre-DNS syntax check"

+.row &%dns_dnssec_ok%&               "parameter for resolver"

 .row &%dns_ipv4_lookup%&             "only v4 lookup for these domains"
 .row &%dns_retrans%&                 "parameter for resolver"
 .row &%dns_retry%&                   "parameter for resolver"
 .row &%dns_ipv4_lookup%&             "only v4 lookup for these domains"
 .row &%dns_retrans%&                 "parameter for resolver"
 .row &%dns_retry%&                   "parameter for resolver"

-.row &%dns_use_dnssec%&              "parameter for resolver"

 .row &%dns_use_edns0%&               "parameter for resolver"
 .row &%hold_domains%&                "hold delivery for these domains"
 .row &%local_interfaces%&            "for routing checks"
 .row &%dns_use_edns0%&               "parameter for resolver"
 .row &%hold_domains%&                "hold delivery for these domains"
 .row &%local_interfaces%&            "for routing checks"


@@ -13776,6 +13959,17 @@ This option controls whether or not an IP address, given as a CSA domain, is
 reversed and looked up in the reverse DNS, as described in more detail in
 section &<<SECTverifyCSA>>&.
 
 reversed and looked up in the reverse DNS, as described in more detail in
 section &<<SECTverifyCSA>>&.
 

+
+.option dns_dnssec_ok main integer -1
+.cindex "DNS" "resolver options"
+.cindex "DNS" "DNSSEC"
+If this option is set to a non-negative number then Exim will initialise the
+DNS resolver library to either use or not use DNSSEC, overriding the system
+default. A value of 0 coerces DNSSEC off, a value of 1 coerces DNSSEC on.
+
+If the resolver library does not support DNSSEC then this option has no effect.
+
+

 .option dns_ipv4_lookup main "domain list&!!" unset
 .cindex "IPv6" "DNS lookup for AAAA records"
 .cindex "DNS" "IPv6 lookup for AAAA records"
 .option dns_ipv4_lookup main "domain list&!!" unset
 .cindex "IPv6" "DNS lookup for AAAA records"
 .cindex "DNS" "IPv6 lookup for AAAA records"


@@ -13806,16 +14000,6 @@ to set in them.
 See &%dns_retrans%& above.
 
 
 See &%dns_retrans%& above.
 
 

-.option dns_use_dnssec main integer -1
-.cindex "DNS" "resolver options"
-.cindex "DNS" "DNSSEC"
-If this option is set to a non-negative number then Exim will initialise the
-DNS resolver library to either use or not use DNSSEC, overriding the system
-default. A value of 0 coerces DNSSEC off, a value of 1 coerces DNSSEC on.
-
-If the resolver library does not support DNSSEC then this option has no effect.
-
-

 .option dns_use_edns0 main integer -1
 .cindex "DNS" "resolver options"
 .cindex "DNS" "EDNS0"
 .option dns_use_edns0 main integer -1
 .cindex "DNS" "resolver options"
 .cindex "DNS" "EDNS0"


@@ -16700,11 +16884,12 @@ and the discussion in chapter &<<CHAPenvironment>>&.
 
 
 
 
 
 

-.option headers_add routers string&!! unset
+.option headers_add routers list&!! unset

 .cindex "header lines" "adding"
 .cindex "router" "adding header lines"
 .cindex "header lines" "adding"
 .cindex "router" "adding header lines"

-This option specifies a string of text that is expanded at routing time, and
-associated with any addresses that are accepted by the router. However, this
+This option specifies a list of text headers, newline-separated,
+that is associated with any addresses that are accepted by the router.
+Each item is separately expanded, at routing time.  However, this

 option has no effect when an address is just being verified. The way in which
 the text is used to add header lines at transport time is described in section
 &<<SECTheadersaddrem>>&. New header lines are not actually added until the
 option has no effect when an address is just being verified. The way in which
 the text is used to add header lines at transport time is described in section
 &<<SECTheadersaddrem>>&. New header lines are not actually added until the


@@ -16713,8 +16898,8 @@ header lines in string expansions in the transport's configuration do not
 &"see"& the added header lines.
 
 The &%headers_add%& option is expanded after &%errors_to%&, but before
 &"see"& the added header lines.
 
 The &%headers_add%& option is expanded after &%errors_to%&, but before

-&%headers_remove%& and &%transport%&. If the expanded string is empty, or if
-the expansion is forced to fail, the option has no effect. Other expansion
+&%headers_remove%& and &%transport%&. If an item is empty, or if
+an item expansion is forced to fail, the item has no effect. Other expansion

 failures are treated as configuration errors.
 
 Unlike most options, &%headers_add%& can be specified multiple times
 failures are treated as configuration errors.
 
 Unlike most options, &%headers_add%& can be specified multiple times


@@ -16736,11 +16921,12 @@ avoided. The &%repeat_use%& option of the &%redirect%& router may be of help.
 
 
 
 
 
 

-.option headers_remove routers string&!! unset
+.option headers_remove routers list&!! unset

 .cindex "header lines" "removing"
 .cindex "router" "removing header lines"
 .cindex "header lines" "removing"
 .cindex "router" "removing header lines"

-This option specifies a string of text that is expanded at routing time, and
-associated with any addresses that are accepted by the router. However, this
+This option specifies a list of text headers, colon-separated,
+that is associated with any addresses that are accepted by the router.
+Each item is separately expanded, at routing time.  However, this

 option has no effect when an address is just being verified. The way in which
 the text is used to remove header lines at transport time is described in
 section &<<SECTheadersaddrem>>&. Header lines are not actually removed until
 option has no effect when an address is just being verified. The way in which
 the text is used to remove header lines at transport time is described in
 section &<<SECTheadersaddrem>>&. Header lines are not actually removed until


@@ -16749,8 +16935,8 @@ to header lines in string expansions in the transport's configuration still
 &"see"& the original header lines.
 
 The &%headers_remove%& option is expanded after &%errors_to%& and
 &"see"& the original header lines.
 
 The &%headers_remove%& option is expanded after &%errors_to%& and

-&%headers_add%&, but before &%transport%&. If the expansion is forced to fail,
-the option has no effect. Other expansion failures are treated as configuration
+&%headers_add%&, but before &%transport%&. If an item expansion is forced to fail,
+the item has no effect. Other expansion failures are treated as configuration

 errors.
 
 Unlike most options, &%headers_remove%& can be specified multiple times
 errors.
 
 Unlike most options, &%headers_remove%& can be specified multiple times


@@ -17593,6 +17779,33 @@ when there is a DNS lookup error.
 
 
 
 
 
 

+.new
+.option dnssec_request_domains dnslookup "domain list&!!" unset
+.cindex "MX record" "security"
+.cindex "DNSSEC" "MX lookup"
+.cindex "security" "MX lookup"
+.cindex "DNS" "DNSSEC"
+DNS lookups for domains matching &%dnssec_request_domains%& will be done with
+the dnssec request bit set.
+This applies to all of the SRV, MX A6, AAAA, A lookup sequence.
+.wen
+
+
+
+.new
+.option dnssec_require_domains dnslookup "domain list&!!" unset
+.cindex "MX record" "security"
+.cindex "DNSSEC" "MX lookup"
+.cindex "security" "MX lookup"
+.cindex "DNS" "DNSSEC"
+DNS lookups for domains matching &%dnssec_request_domains%& will be done with
+the dnssec request bit set.  Any returns not having the Authenticated Data bit
+(AD bit) set wil be ignored and logged as a host-lookup failure.
+This applies to all of the SRV, MX A6, AAAA, A lookup sequence.
+.wen
+
+
+

 .option mx_domains dnslookup "domain list&!!" unset
 .cindex "MX record" "required to exist"
 .cindex "SRV record" "required to exist"
 .option mx_domains dnslookup "domain list&!!" unset
 .cindex "MX record" "required to exist"
 .cindex "SRV record" "required to exist"


@@ -19750,10 +19963,11 @@ value that the router supplies, and also overriding any value associated with
 &%user%& (see below).
 
 
 &%user%& (see below).
 
 

-.option headers_add transports string&!! unset
+.option headers_add transports list&!! unset

 .cindex "header lines" "adding in transport"
 .cindex "transport" "header lines; adding"
 .cindex "header lines" "adding in transport"
 .cindex "transport" "header lines; adding"

-This option specifies a string of text that is expanded and added to the header
+This option specifies a list of text headers, newline-separated,
+which are (separately) expanded and added to the header

 portion of a message as it is transported, as described in section
 &<<SECTheadersaddrem>>&. Additional header lines can also be specified by
 routers. If the result of the expansion is an empty string, or if the expansion
 portion of a message as it is transported, as described in section
 &<<SECTheadersaddrem>>&. Additional header lines can also be specified by
 routers. If the result of the expansion is an empty string, or if the expansion


@@ -19774,18 +19988,20 @@ transports, the settings of &%message_prefix%& and &%message_suffix%& should be
 checked, since this option does not automatically suppress them.
 
 
 checked, since this option does not automatically suppress them.
 
 

-.option headers_remove transports string&!! unset
+.option headers_remove transports list&!! unset

 .cindex "header lines" "removing"
 .cindex "transport" "header lines; removing"
 .cindex "header lines" "removing"
 .cindex "transport" "header lines; removing"

-This option specifies a string that is expanded into a list of header names;
+This option specifies a list of header names, colon-separated;

 these headers are omitted from the message as it is transported, as described
 in section &<<SECTheadersaddrem>>&. Header removal can also be specified by
 these headers are omitted from the message as it is transported, as described
 in section &<<SECTheadersaddrem>>&. Header removal can also be specified by

-routers. If the result of the expansion is an empty string, or if the expansion
+routers.
+Each list item is separately expanded.
+If the result of the expansion is an empty string, or if the expansion

 is forced to fail, no action is taken. Other expansion failures are treated as
 errors and cause the delivery to be deferred.
 
 Unlike most options, &%headers_remove%& can be specified multiple times
 is forced to fail, no action is taken. Other expansion failures are treated as
 errors and cause the delivery to be deferred.
 
 Unlike most options, &%headers_remove%& can be specified multiple times

-for a router; all listed headers are added.
+for a router; all listed headers are removed.

 
 
 
 
 
 


@@ -22493,6 +22709,33 @@ See the &%search_parents%& option in chapter &<<CHAPdnslookup>>& for more
 details.
 
 
 details.
 
 

+.new
+.option dnssec_request_domains smtp "domain list&!!" unset
+.cindex "MX record" "security"
+.cindex "DNSSEC" "MX lookup"
+.cindex "security" "MX lookup"
+.cindex "DNS" "DNSSEC"
+DNS lookups for domains matching &%dnssec_request_domains%& will be done with
+the dnssec request bit set.
+This applies to all of the SRV, MX A6, AAAA, A lookup sequence.
+.wen
+
+
+
+.new
+.option dnssec_require_domains smtp "domain list&!!" unset
+.cindex "MX record" "security"
+.cindex "DNSSEC" "MX lookup"
+.cindex "security" "MX lookup"
+.cindex "DNS" "DNSSEC"
+DNS lookups for domains matching &%dnssec_request_domains%& will be done with
+the dnssec request bit set.  Any returns not having the Authenticated Data bit
+(AD bit) set wil be ignored and logged as a host-lookup failure.
+This applies to all of the SRV, MX A6, AAAA, A lookup sequence.
+.wen
+
+
+

 .option dscp smtp string&!! unset
 .cindex "DCSP" "outbound"
 This option causes the DSCP value associated with a socket to be set to one
 .option dscp smtp string&!! unset
 .cindex "DCSP" "outbound"
 This option causes the DSCP value associated with a socket to be set to one


@@ -22980,6 +23223,14 @@ unknown state), opens a new one to the same host, and then tries the delivery
 in clear.
 
 
 in clear.
 
 

+.option tls_try_verify_hosts smtp "host list&!! unset
+.cindex "TLS" "server certificate verification"
+.cindex "certificate" "verification of server"
+This option gives a list of hosts for which, on encrypted connections,
+certificate verification will be tried but need not succeed.
+The &%tls_verify_certificates%& option must also be set.
+
+

 .option tls_verify_certificates smtp string&!! unset
 .cindex "TLS" "server certificate verification"
 .cindex "certificate" "verification of server"
 .option tls_verify_certificates smtp string&!! unset
 .cindex "TLS" "server certificate verification"
 .cindex "certificate" "verification of server"


@@ -22994,6 +23245,20 @@ single file if you are using GnuTLS. The values of &$host$& and
 &$host_address$& are set to the name and address of the server during the
 expansion of this option. See chapter &<<CHAPTLS>>& for details of TLS.
 
 &$host_address$& are set to the name and address of the server during the
 expansion of this option. See chapter &<<CHAPTLS>>& for details of TLS.
 

+For back-compatability,
+if neither tls_verify_hosts nor tls_try_verify_hosts are set
+and certificate verification fails the TLS connection is closed.
+
+
+.option tls_verify_hosts smtp "host list&!! unset
+.cindex "TLS" "server certificate verification"
+.cindex "certificate" "verification of server"
+This option gives a list of hosts for which. on encrypted connections,
+certificate verification must succeed.
+The &%tls_verify_certificates%& option must also be set.
+If both this option and &%tls_try_verify_hosts%& are unset
+operation is as if this option selected all hosts.
+

 
 
 
 
 
 


@@ -25895,6 +26160,12 @@ for OpenSSL only (not GnuTLS), a directory, that contains a collection of
 expected server certificates. The client verifies the server's certificate
 against this collection, taking into account any revoked certificates that are
 in the list defined by &%tls_crl%&.
 expected server certificates. The client verifies the server's certificate
 against this collection, taking into account any revoked certificates that are
 in the list defined by &%tls_crl%&.

+Failure to verify fails the TLS connection unless either of the
+&%tls_verify_hosts%& or &%tls_try_verify_hosts%& options are set.
+
+The &%tls_verify_hosts%& and &%tls_try_verify_hosts%& options restrict
+certificate verification to the listed servers.  Verification either must
+or need not succeed respectively.

 
 If
 &%tls_require_ciphers%& is set on the &(smtp)& transport, it must contain a
 
 If
 &%tls_require_ciphers%& is set on the &(smtp)& transport, it must contain a


@@ -27254,7 +27525,16 @@ It is usable in the RCPT ACL and valid only for single-recipient mails forwarded
 from one SMTP connection to another.  If a recipient-verify callout connection is
 requested in the same ACL it is held open and used for the data, otherwise one is made
 after the ACL completes.
 from one SMTP connection to another.  If a recipient-verify callout connection is
 requested in the same ACL it is held open and used for the data, otherwise one is made
 after the ACL completes.

-Note that routers are used in verify mode.
+
+Note that routers are used in verify mode,
+and cannot depend on content of received headers.
+Note also that headers cannot be
+modified by any of the post-data ACLs (DATA, MIME and DKIM).
+Headers may be modified by routers (subject to the above) and transports.
+
+Cutthrough delivery is not supported via transport-filters or when DKIM signing
+of outgoing messages is done, because it sends data to the ultimate destination
+before the entire message has been received from the source.

 
 Should the ultimate destination system positively accept or reject the mail,
 a corresponding indication is given to the source system and nothing is queued.
 
 Should the ultimate destination system positively accept or reject the mail,
 a corresponding indication is given to the source system and nothing is queued.


@@ -27508,12 +27788,15 @@ warn dnslists = sbl.spamhaus.org : \
      add_header = X-blacklisted-at: $dnslist_domain
 .endd
 The &%add_header%& modifier is permitted in the MAIL, RCPT, PREDATA, DATA,
      add_header = X-blacklisted-at: $dnslist_domain
 .endd
 The &%add_header%& modifier is permitted in the MAIL, RCPT, PREDATA, DATA,

-MIME, and non-SMTP ACLs (in other words, those that are concerned with
+MIME, DKIM, and non-SMTP ACLs (in other words, those that are concerned with

 receiving a message). The message must ultimately be accepted for
 &%add_header%& to have any significant effect. You can use &%add_header%& with
 any ACL verb, including &%deny%& (though this is potentially useful only in a
 RCPT ACL).
 
 receiving a message). The message must ultimately be accepted for
 &%add_header%& to have any significant effect. You can use &%add_header%& with
 any ACL verb, including &%deny%& (though this is potentially useful only in a
 RCPT ACL).
 

+Headers will not be added to the message if the modifier is used in
+DATA, MIME or DKIM ACLs for messages delivered by cutthrough routing.
+

 Leading and trailing newlines are removed from
 the data for the &%add_header%& modifier; if it then
 contains one or more newlines that
 Leading and trailing newlines are removed from
 the data for the &%add_header%& modifier; if it then
 contains one or more newlines that


@@ -27607,12 +27890,15 @@ warn   message        = Remove internal headers
        remove_header  = x-route-mail1 : x-route-mail2
 .endd
 The &%remove_header%& modifier is permitted in the MAIL, RCPT, PREDATA, DATA,
        remove_header  = x-route-mail1 : x-route-mail2
 .endd
 The &%remove_header%& modifier is permitted in the MAIL, RCPT, PREDATA, DATA,

-MIME, and non-SMTP ACLs (in other words, those that are concerned with
+MIME, DKIM, and non-SMTP ACLs (in other words, those that are concerned with

 receiving a message). The message must ultimately be accepted for
 &%remove_header%& to have any significant effect. You can use &%remove_header%&
 with any ACL verb, including &%deny%&, though this is really not useful for
 any verb that doesn't result in a delivered message.
 
 receiving a message). The message must ultimately be accepted for
 &%remove_header%& to have any significant effect. You can use &%remove_header%&
 with any ACL verb, including &%deny%&, though this is really not useful for
 any verb that doesn't result in a delivered message.
 

+Headers will not be removed to the message if the modifier is used in
+DATA, MIME or DKIM ACLs for messages delivered by cutthrough routing.
+

 More than one header can be removed at the same time by using a colon separated
 list of header names. The header matching is case insensitive. Wildcards are
 not permitted, nor is list expansion performed, so you cannot use hostlists to
 More than one header can be removed at the same time by using a colon separated
 list of header names. The header matching is case insensitive. Wildcards are
 not permitted, nor is list expansion performed, so you cannot use hostlists to


@@ -27933,6 +28219,23 @@ This condition checks whether the sending host (the client) is authorized to
 send email. Details of how this works are given in section
 &<<SECTverifyCSA>>&.
 
 send email. Details of how this works are given in section
 &<<SECTverifyCSA>>&.
 

+.new
+.vitem &*verify&~=&~header_names_ascii*&
+.cindex "&%verify%& ACL condition"
+.cindex "&ACL;" "verifying header names only ASCII"
+.cindex "header lines" "verifying header names only ASCII"
+.cindex "verifying" "header names only ASCII"
+This condition is relevant only in an ACL that is run after a message has been
+received, that is, in an ACL specified by &%acl_smtp_data%& or
+&%acl_not_smtp%&.  It checks all header names (not the content) to make sure
+there are no non-ASCII characters, also excluding control characters.  The
+allowable characters are decimal ASCII values 33 through 126.
+
+Exim itself will handle headers with non-ASCII characters, but it can cause
+problems for downstream applications, so this option will allow their
+detection and rejection in the DATA ACL's.
+.wen
+

 .vitem &*verify&~=&~header_sender/*&<&'options'&>
 .cindex "&%verify%& ACL condition"
 .cindex "&ACL;" "verifying sender in the header"
 .vitem &*verify&~=&~header_sender/*&<&'options'&>
 .cindex "&%verify%& ACL condition"
 .cindex "&ACL;" "verifying sender in the header"


@@ -28544,6 +28847,13 @@ deny   condition = ${if isip4{$sender_host_address}}
        dnslists  = some.list.example
 .endd
 
        dnslists  = some.list.example
 .endd
 

+If an explicit key is being used for a DNS lookup and it may be an IPv6
+address you should specify alternate list separators for both the outer
+(DNS list name) list and inner (lookup keys) list:
+.code
+       dnslists = <; dnsbl.example.com/<|$acl_m_addrslist
+.endd
+

 .section "Rate limiting incoming messages" "SECTratelimiting"
 .cindex "rate limiting" "client sending"
 .cindex "limiting client sending rates"
 .section "Rate limiting incoming messages" "SECTratelimiting"
 .cindex "rate limiting" "client sending"
 .cindex "limiting client sending rates"


@@ -28925,6 +29235,7 @@ router that does not set up hosts routes to an &(smtp)& transport with a
 &%hosts%& setting, the transport's hosts are used. If an &(smtp)& transport has
 &%hosts_override%& set, its hosts are always used, whether or not the router
 supplies a host list.
 &%hosts%& setting, the transport's hosts are used. If an &(smtp)& transport has
 &%hosts_override%& set, its hosts are always used, whether or not the router
 supplies a host list.

+Callouts are only supported on &(smtp)& transports.

 
 The port that is used is taken from the transport, if it is specified and is a
 remote transport. (For routers that do verification only, no transport need be
 
 The port that is used is taken from the transport, if it is specified and is a
 remote transport. (For routers that do verification only, no transport need be


@@ -29728,6 +30039,24 @@ av_scanner = mksd:2
 .endd
 You can safely omit this option (the default value is 1).
 
 .endd
 You can safely omit this option (the default value is 1).
 

+.vitem &%sock%&
+.cindex "virus scanners" "simple socket-connected"
+This is a general-purpose way of talking to simple scanner daemons
+running on the local machine.
+There are four options:
+an address (which may be an IP addres and port, or the path of a Unix socket),
+a commandline to send (may include a single %s which will be replaced with
+the path to the mail file to be scanned),
+an RE to trigger on from the returned data,
+an RE to extract malware_name from the returned data.
+For example:
+.code
+av_scanner = sock:127.0.0.1 6001:%s:(SPAM|VIRUS):(.*)\$
+.endd
+Default for the socket specifier is &_/tmp/malware.sock_&.
+Default for the commandline is &_%s\n_&.
+Both regular-expressions are required.
+

 .vitem &%sophie%&
 .cindex "virus scanners" "Sophos and Sophie"
 Sophie is a daemon that uses Sophos' &%libsavi%& library to scan for viruses.
 .vitem &%sophie%&
 .cindex "virus scanners" "Sophos and Sophie"
 Sophie is a daemon that uses Sophos' &%libsavi%& library to scan for viruses.


@@ -31850,7 +32179,7 @@ they do not affect the values of the variables that refer to header lines.
 the transport cannot refer to the modified header lines, because such
 expansions all occur before the message is actually transported.
 
 the transport cannot refer to the modified header lines, because such
 expansions all occur before the message is actually transported.
 

-For both routers and transports, the result of expanding a &%headers_add%&
+For both routers and transports, the argument of a &%headers_add%&

 option must be in the form of one or more RFC 2822 header lines, separated by
 newlines (coded as &"\n"&). For example:
 .code
 option must be in the form of one or more RFC 2822 header lines, separated by
 newlines (coded as &"\n"&). For example:
 .code


@@ -31860,10 +32189,10 @@ headers_add = X-added-header: added by $primary_hostname\n\
 Exim does not check the syntax of these added header lines.
 
 Multiple &%headers_add%& options for a single router or transport can be
 Exim does not check the syntax of these added header lines.
 
 Multiple &%headers_add%& options for a single router or transport can be

-specified; the values will be concatenated (with a separating newline
-added) before expansion.
+specified; the values will append to a single list of header lines.
+Each header-line is separately expanded.

 
 

-The result of expanding &%headers_remove%& must consist of a colon-separated
+The argument of a &%headers_remove%& option must consist of a colon-separated

 list of header names. This is confusing, because header names themselves are
 often terminated by colons. In this case, the colons are the list separators,
 not part of the names. For example:
 list of header names. This is confusing, because header names themselves are
 often terminated by colons. In this case, the colons are the list separators,
 not part of the names. For example:


@@ -31872,11 +32201,12 @@ headers_remove = return-receipt-to:acknowledge-to
 .endd
 
 Multiple &%headers_remove%& options for a single router or transport can be
 .endd
 
 Multiple &%headers_remove%& options for a single router or transport can be

-specified; the values will be concatenated (with a separating colon
-added) before expansion.
+specified; the arguments will append to a single header-names list.
+Each item is separately expanded.

 
 

-When &%headers_add%& or &%headers_remove%& is specified on a router, its value
-is expanded at routing time, and then associated with all addresses that are
+When &%headers_add%& or &%headers_remove%& is specified on a router,
+items are expanded at routing time,
+and then associated with all addresses that are

 accepted by that router, and also with any new addresses that it generates. If
 an address passes through several routers as a result of aliasing or
 forwarding, the changes are cumulative.
 accepted by that router, and also with any new addresses that it generates. If
 an address passes through several routers as a result of aliasing or
 forwarding, the changes are cumulative.


@@ -33974,6 +34304,7 @@ the following table:
 &`R   `&        on &`<=`& lines: reference for local bounce
 &`    `&        on &`=>`&  &`**`& and &`==`& lines: router name
 &`S   `&        size of message
 &`R   `&        on &`<=`& lines: reference for local bounce
 &`    `&        on &`=>`&  &`**`& and &`==`& lines: router name
 &`S   `&        size of message

+&`SNI `&        server name indication from TLS client hello

 &`ST  `&        shadow transport name
 &`T   `&        on &`<=`& lines: message subject (topic)
 &`    `&        on &`=>`& &`**`& and &`==`& lines: transport name
 &`ST  `&        shadow transport name
 &`T   `&        on &`<=`& lines: message subject (topic)
 &`    `&        on &`=>`& &`**`& and &`==`& lines: transport name


@@ -34283,7 +34614,8 @@ The message that is written is &"spool file is locked"&.
 .next
 .cindex "log" "smtp confirmation"
 .cindex "SMTP" "logging confirmation"
 .next
 .cindex "log" "smtp confirmation"
 .cindex "SMTP" "logging confirmation"

-&%smtp_confirmation%&: The response to the final &"."& in the SMTP dialogue for
+.cindex "LMTP" "logging confirmation"
+&%smtp_confirmation%&: The response to the final &"."& in the SMTP or LMTP dialogue for

 outgoing messages is added to delivery log lines in the form &`C=`&<&'text'&>.
 A number of MTAs (including Exim) return an identifying string in this
 response.
 outgoing messages is added to delivery log lines in the form &`C=`&<&'text'&>.
 A number of MTAs (including Exim) return an identifying string in this
 response.


@@ -34512,9 +34844,17 @@ This utility is a Perl script contributed by Matt Hubbard. It runs
 .code
 exim -bpu
 .endd
 .code
 exim -bpu
 .endd

-to obtain a queue listing with undelivered recipients only, and then greps the
-output to select messages that match given criteria. The following selection
-options are available:
+or (in case &*-a*& switch is specified)
+.code
+exim -bp
+.endd
+.new
+The &*-C*& option is used to specify an alternate &_exim.conf_& which might
+contain alternate exim configuration the queue management might be using.
+.wen
+
+to obtain a queue listing, and then greps the output to select messages 
+that match given criteria. The following selection options are available:

 
 .vlist
 .vitem &*-f*&&~<&'regex'&>
 
 .vlist
 .vitem &*-f*&&~<&'regex'&>


@@ -34561,6 +34901,9 @@ Brief format &-- one line per message.
 
 .vitem &*-R*&
 Display messages in reverse order.
 
 .vitem &*-R*&
 Display messages in reverse order.

+
+.vitem &*-a*&
+Include delivered recipients in queue listing.

 .endlist
 
 There is one more option, &%-h%&, which outputs a list of options.
 .endlist
 
 There is one more option, &%-h%&, which outputs a list of options.


@@ -36300,7 +36643,9 @@ disabled by setting DISABLE_DKIM=yes in Local/Makefile.
 Exim's DKIM implementation allows to
 .olist
 Sign outgoing messages: This function is implemented in the SMTP transport.
 Exim's DKIM implementation allows to
 .olist
 Sign outgoing messages: This function is implemented in the SMTP transport.

-It can co-exist with all other Exim features, including transport filters.
+It can co-exist with all other Exim features
+(including transport filters)
+except cutthrough delivery.

 .next
 Verify signatures in incoming messages: This is implemented by an additional
 ACL (acl_smtp_dkim), which can be called several times per message, with
 .next
 Verify signatures in incoming messages: This is implemented by an additional
 ACL (acl_smtp_dkim), which can be called several times per message, with


@@ -36391,6 +36736,10 @@ used.
 Verification of DKIM signatures in incoming email is implemented via the
 &%acl_smtp_dkim%& ACL. By default, this ACL is called once for each
 syntactically(!) correct signature in the incoming message.
 Verification of DKIM signatures in incoming email is implemented via the
 &%acl_smtp_dkim%& ACL. By default, this ACL is called once for each
 syntactically(!) correct signature in the incoming message.

+A missing ACL definition defaults to accept.
+If any ACL call does not acccept, the message is not accepted.
+If a cutthrough delivery was in progress for the message it is
+summarily dropped (having wasted the transmission effort).

 
 To evaluate the signature in the ACL a large number of expansion variables
 containing the signature status and its details are set up during the
 
 To evaluate the signature in the ACL a large number of expansion variables
 containing the signature status and its details are set up during the