-
. /////////////////////////////////////////////////////////////////////////////
. This is the primary source of the Exim Manual. It is an xfpt document that is
. converted into DocBook XML for subsequent conversion into printable and online
. Update the Copyright year (only) when changing content.
. /////////////////////////////////////////////////////////////////////////////
-.set previousversion "4.96"
+.set previousversion "4.97"
.include ./local_params
.set ACL "access control lists (ACLs)"
.set drivernamemax "64"
.macro copyyear
-2022
+2024
.endmacro
. /////////////////////////////////////////////////////////////////////////////
way of representing the date and time of day).
.next
After the first hyphen, the next
-.new
eleven
-.wen
characters are the id of the process that received the message.
.next
-.new
There are two different possibilities for the final four characters:
.olist
.oindex "&%localhost_number%&"
500000 (250000) and added to
the fractional part of the time, which in this case is in units of 2 us (4 us).
.endlist
-.wen
.endlist
After a message has been received, Exim waits for the clock to tick at the
Yet another DBM library, called &'tdb'&, is available from
&url(https://sourceforge.net/projects/tdb/files/). It has its own interface, and also
operates on a single file.
+.next
+.new
+It is possible to use sqlite3 (&url(https://www.sqlite.org/index.html))
+for the DBM library.
+.wen
.endlist
.cindex "USE_DB"
.code
USE_DB=yes
.endd
-Similarly, for gdbm you set USE_GDBM, and for tdb you set USE_TDB. An
-error is diagnosed if you set more than one of these.
+Similarly, for gdbm you set USE_GDBM, for tdb you set USE_TDB,
+and for sqlite3 you set USE_SQLITE.
+An error is diagnosed if you set more than one of these.
You can set USE_NDBM if needed to override an operating system default.
At the lowest level, the build-time configuration sets none of these options,
.code
DBMLIB = -ldb
DBMLIB = -ltdb
+DBMLIB = -lsqlite3
DBMLIB = -lgdbm -lgdbm_compat
.endd
The last of those was for a Linux having GDBM provide emulated NDBM facilities.
referenced from the configuration (for example, alias files) are changed,
because these are reread each time they are used.
-.new
Either a SIGTERM or a SIGINT signal should be used to cause the daemon
to cleanly shut down.
Subprocesses handling recceiving or delivering messages,
or for scanning the queue,
will not be affected by the termination of the daemon process.
-.wen
.cmdopt -bdf
This option has the same effect as &%-bd%& except that it never disconnects
Because macros in the config file are often used for secrets, those are only
available to admin users.
-.new
The word &"set"& at the start of a line, followed by a single space,
is recognised specially as defining a value for a variable.
-The syntax is otherwise the same as the ACL modifier &"set ="&.
+.new
+.cindex "tainted data" "expansion testing"
+If the sequence &",t"& is inserted before the space,
+the value is marked as tainted.
.wen
+The syntax is otherwise the same as the ACL modifier &"set ="&.
.cmdopt -bem <&'filename'&>
.cindex "testing" "string expansion"
suppressing this for special cases.
Policy checks on the contents of local messages can be enforced by means of
-the non-SMTP ACL. See chapter &<<CHAPACL>>& for details.
+the non-SMTP ACL. See section &<<SECnonSMTP>>& for details.
.cindex "return code" "for &%-bm%&"
The return code is zero if the message is successfully accepted. Otherwise, the
provoked if the terminating dot is missing. A further message may then follow.
As for other local message submissions, the contents of incoming batch SMTP
-messages can be checked using the non-SMTP ACL (see chapter &<<CHAPACL>>&).
+messages can be checked using the non-SMTP ACL (see section &<<SECnonSMTP>>&).
Unqualified addresses are automatically qualified using &%qualify_domain%& and
&%qualify_recipient%&, as appropriate, unless the &%-bnq%& option is used.
given.
Normally the daemon creates this socket, unless a &%-oX%& and &*no*& &%-oP%&
option is also present.
-.new
If this option is given then the socket will not be created. This is required
if the system is running multiple daemons, in which case it should
be used on all.
.next
obtaining a current queue size
.endlist
-.wen
.cmdopt -pd
.cindex "Perl" "starting the interpreter"
.cindex "multiple SMTP deliveries"
connection because of the hints that were set up during the first queue scan.
-.new
Two-phase queue runs should be used on systems which, even intermittently,
have a large queue (such as mailing-list operators).
They may also be useful for hosts that are connected to the Internet
intermittently.
-.wen
.vitem &%-q[q]i...%&
.oindex "&%-qi%&"
Such a daemon listens for incoming SMTP calls, and also starts a queue runner
process every 30 minutes.
-.new
.cindex "named queues" "queue runners"
It is possible to set up runners for multiple named queues within one daemon,
For example:
.code
exim -qGhipri/2m -q10m -qqGmailinglist/1h
.endd
-.wen
When a daemon is started by &%-q%& with a time value, but without &%-bd%&, no
pid file is written unless one is explicitly requested by the &%-oP%& option.
The &%-R%& option makes it straightforward to initiate delivery of all messages
to a given domain after a host has been down for some time. When the SMTP
-command ETRN is accepted by its ACL (see chapter &<<CHAPACL>>&), its default
+command ETRN is accepted by its ACL (see section &<<SECTETRN>>&), its default
effect is to run Exim with the &%-R%& option, but it can be configured to run
an arbitrary command instead.
For the string-expansion kind of lookups, the query is given in the first
bracketed argument of the &${lookup ...}$& expansion.
-For the list-argument kind of lookup the quury is given by the remainder of the
+For the list-argument kind of lookup the query is given by the remainder of the
list item after the first semicolon.
.cindex "tainted data" "quoting for lookups"
-If tainted data is used in the query then it should be quuted by
+If tainted data is used in the query then it should be quoted by
using the &*${quote_*&<&'lookup-type'&>&*:*&<&'string'&>&*}*& expansion operator
appropriate for the lookup.
.endlist
.cindex "dsearch lookup type"
The given file must be an absolute directory path; this is searched for an entry
whose name is the key by calling the &[lstat()]& function.
-The key may not contain any forward slash characters.
+.new
+Unless the options (below) permit a path,
+.wen
+the key may not contain any forward slash characters.
If &[lstat()]& succeeds then so does the lookup.
.cindex "tainted data" "dsearch result"
The result is regarded as untainted.
separated by a comma. Options, if present, are a comma-separated list having
each element starting with a tag name and an equals.
-Two options are supported, for the return value and for filtering match
+Three options are supported, for the return value and for filtering match
candidates.
The "ret" option requests an alternate result value of
the entire path for the entry. Example:
${lookup {passwd} dsearch,ret=full {/etc}}
.endd
The default result is just the requested entry.
+
The "filter" option requests that only directory entries of a given type
are matched. The match value is one of "file", "dir" or "subdir" (the latter
not matching "." or ".."). Example:
The default matching is for any entry type, including directories
and symlinks.
+The "key" option relaxes the restriction that only a simple path component can
+be searched for, to permit a sequence of path components. Example:
+.code
+${lookup {foo/bar} dsearch,key=path {/etc}}
+.endd
+If this option is used, a ".." component in the key is specifically disallowed.
+The default operation is that the key may only be a single path component.
+
An example of how this
lookup can be used to support virtual domains is given in section
&<<SECTvirtualdomains>>&.
lookup types support only literal keys.
&*Warning 2*&: In a host list, you must always use &(net-iplsearch)& so that
-the implicit key is the host's IP address rather than its name (see section
-&<<SECThoslispatsikey>>&).
+the implicit key is the host's IP address rather than its name
+(see section &<<SECThoslispatsikey>>&).
&*Warning 3*&: Do not use an IPv4-mapped IPv6 address for a key; use the
IPv4, in dotted-quad form. (Exim converts IPv4-mapped IPv6 addresses to this
[name="${quote_nisplus:$local_part}"]
.endd
.cindex "tainted data" "in lookups"
-.new
&*All*& tainted data used in a query-style lookup must be quoted
using a mechanism appropriate for the lookup type.
-.wen
See chapter &<<CHAPexpand>>& for full coverage of string expansions. The quote
operator can be used for all lookup types, but has no effect for single-key
lookups, since no quoting is ever needed in their key strings.
${lookup pgsql,servers=master/db/name/pw {UPDATE ...} }
.endd
-An older syntax places the servers specification before the query,
+.new
+A now-deprecated syntax places the servers specification before the query,
semicolon separated:
.code
${lookup mysql{servers=master; UPDATE ...} }
.endd
-The new version avoids potential issues with tainted
-arguments in the query, for explicit expansion.
+The new version avoids issues with tainted
+arguments explicitly expanded as part of the query.
+The entire string within the braces becomes tainted,
+including the server sepcification - which is not permissible.
+If the older sytax is used, a warning message will be logged.
+This syntax will be removed in a future release.
+.wen
+
&*Note*&: server specifications in list-style lookups are still problematic.
anything (for example, setting a field to the value it already has), the result
is zero because no rows are affected.
+.new
+To get an encryted connection, use a Mysql option file with the required
+parameters for the connection.
+.wen
+
.subsection "Special PostgreSQL features" SECID74
PostgreSQL lookups can also use Unix domain socket connections to the database.
.section "Expansion of lists" "SECTlistexpand"
.cindex "expansion" "of lists"
Each list is expanded as a single string before it is used.
+.cindex "tainted data" tracking
+&*Note*&: As a result, if any componend was tainted then the
+entire result string becomes tainted.
&'Exception: the router headers_remove option, where list-item
splitting is done before string-expansion.'&
&*Reminder*&: With this kind of pattern, you must have host &'names'& as
keys in the file, not IP addresses. If you want to do lookups based on IP
-addresses, you must precede the search type with &"net-"& (see section
-&<<SECThoslispatsikey>>&). There is, however, no reason why you could not use
+addresses, you must precede the search type with &"net-"&
+(see section &<<SECThoslispatsikey>>&).
+There is, however, no reason why you could not use
two items in the same list, one doing an address lookup and one doing a name
lookup, both using the same file.
below in section &<<SECTexpansionitems>>& onwards. Backslash is used as an
escape character, as described in the following section.
+.cindex "tainted data" tracking
+If any porttion of the result string is tainted, the entire result is.
+
Whether a string is expanded depends upon the context. Usually this is solely
dependent upon the option for which a value is sought; in this documentation,
options for which string expansion is performed are marked with † after
database lookups, and the use of expansion operators such as &%sg%&, &%substr%&
and &%nhash%&.
-.new
When reading lines from the standard input,
macros can be defined and ACL variables can be set.
For example:
set acl_m_myvar = bar
.endd
Such macros and variables can then be used in later input lines.
-.wen
Exim gives up its root privilege when it is called with the &%-be%& option, and
instead runs under the uid and gid it was called with, to prevent users from
add_header = :at_start:${authresults {$primary_hostname}}
.endd
This is safe even if no authentication results are available
-.new
and would generally be placed in the DATA ACL.
-.wen
.vitem "&*${certextract{*&<&'field'&>&*}{*&<&'certificate'&>&*}&&&
For each item
in this list, its value is placed in &$item$&, and then the condition is
evaluated.
-.new
Any modification of &$value$& by this evaluation is discarded.
-.wen
If the condition is true, &$item$& is added to the output as an
item in a new list; if the condition is false, the item is discarded. The
separator used for the output list is the same as the one used for the
This item inserts &"raw"& header lines. It is described with the &%header%&
expansion item in section &<<SECTexpansionitems>>& above.
-.vitem "&*${run<&'options'&> {*&<&'command&~arg&~list'&>&*}{*&<&'string1'&>&*}&&&
+.vitem "&*${run<&'options'&> {*&<&'command&~string'&>&*}{*&<&'string1'&>&*}&&&
{*&<&'string2'&>&*}}*&"
.cindex "expansion" "running a command"
.cindex "&%run%& expansion item"
and without whitespace.
If the option &'preexpand'& is not used,
-the command string is split into individual arguments by spaces
-and then each argument is expanded.
+the command string before expansion is split into individual arguments by spaces
+and then each argument is separately expanded.
Then the command is run
in a separate process, but under the same uid and gid. As in other command
executions from Exim, a shell is not used by default. If the command requires
a careful assessment for security vulnerabilities should be done.
If the option &'preexpand'& is used,
-the command and its arguments are first expanded as one string. The result is
-split apart into individual arguments by spaces, and then the command is run
-as above.
+the command string is first expanded as a whole.
+The expansion result is split apart into individual arguments by spaces,
+and then the command is run as above.
Since the arguments are split by spaces, when there is a variable expansion
which has an empty result, it will cause the situation that the argument will
simply be omitted when the program is actually executed by Exim. If the
-.new
.vitem &*${headerwrap_*&<&'cols'&>&*_*&<&'limit'&>&*:*&<&'string'&>&*}*&
.cindex header "wrapping operator"
.cindex expansion "header wrapping"
Whitespace at a chosen wrap point is removed.
A line-wrap consists of a newline followed by a tab,
and the tab is counted as 8 columns.
-.wen
.cindex "&%utf8_localpart_from_alabel%& expansion item"
These convert EAI mail name components between UTF-8 and a-label forms.
For information on internationalisation support see &<<SECTi18nMTA>>&.
+
+
+.new
+.vitem &*${xtextd:*&<&'string'&>&*}*&
+.cindex "text forcing in strings"
+.cindex "string" "xtext decoding"
+.cindex "xtext"
+.cindex "&%xtextd%& expansion item"
+This performs xtext decoding of the string (per RFC 3461 section 4).
+.wen
+
+
+
.endlist
.next
The item @[] matches any of the local host's interface addresses.
.next
-Single-key lookups are assumed to be like &"net-"& style lookups in host lists,
+Single-key lookups are assumed to be like &"net-"& style lookups in host lists
+(see section &<<SECThoslispatsikey>>&),
even if &`net-`& is not specified. There is never any attempt to turn the IP
address into a host name. The most common type of linear search for
&*match_ip*& is likely to be &*iplsearch*&, in which the file can contain CIDR
rejections of MAIL and rejections of RCPT.
.tvar &$recipients$&
-.new
.tvar &$recipients_list$&
These variables both contain the envelope recipients for a message.
this variable is not intended for further processing.
The second is a proper Exim list; colon-separated.
-.wen
However, the variables
are not generally available, to prevent exposure of Bcc recipients in
.row &%acl_smtp_rcpt%& "ACL for RCPT"
.row &%acl_smtp_starttls%& "ACL for STARTTLS"
.row &%acl_smtp_vrfy%& "ACL for VRFY"
+.row &%acl_smtp_wellknown%& "ACL for WELLKNOWN"
.row &%av_scanner%& "specify virus scanner"
.row &%check_rfc2047_length%& "check length of RFC 2047 &""encoded &&&
words""&"
.row &%dsn_advertise_hosts%& "advertise DSN extensions to these hosts"
.row &%ignore_fromline_hosts%& "allow &""From ""& from these hosts"
.row &%ignore_fromline_local%& "allow &""From ""& from local SMTP"
+.row &%limits_advertise_hosts%& "advertise LIMITS to these hosts"
.row &%pipelining_advertise_hosts%& "advertise pipelining to these hosts"
.row &%pipelining_connect_advertise_hosts%& "advertise pipelining to these hosts"
.row &%prdr_enable%& "advertise PRDR to all hosts"
.row &%smtputf8_advertise_hosts%& "advertise SMTPUTF8 to these hosts"
.row &%tls_advertise_hosts%& "advertise TLS to these hosts"
+.row &%wellknown_advertise_hosts%& "advertise WELLKNOWN to these hosts"
.endtable
.cindex "&ACL;" "for non-SMTP messages"
.cindex "non-SMTP messages" "ACLs for"
This option defines the ACL that is run when a non-SMTP message has been
-read and is on the point of being accepted. See chapter &<<CHAPACL>>& for
+read and is on the point of being accepted. See section &<<SECnonSMTP>>& for
further details.
.option acl_not_smtp_mime main string&!! unset
.cindex "&ACL;" "at start of non-SMTP message"
.cindex "non-SMTP messages" "ACLs for"
This option defines the ACL that is run before Exim starts reading a
-non-SMTP message. See chapter &<<CHAPACL>>& for further details.
+non-SMTP message. See section &<<SECnonSMTP>>& for further details.
.option acl_smtp_auth main string&!! unset
.cindex "&ACL;" "setting up for SMTP commands"
.cindex "AUTH" "ACL for"
This option defines the ACL that is run when an SMTP AUTH command is
-received. See chapter &<<CHAPACL>>& for further details.
+received.
+See chapter &<<CHAPACL>>& for general information on ACLs, and chapter
+&<<CHAPSMTPAUTH>>& for details of authentication.
.option acl_smtp_connect main string&!! unset
.cindex "&ACL;" "on SMTP connection"
This option defines the ACL that is run when an SMTP connection is received.
-See chapter &<<CHAPACL>>& for further details.
+See section &<<SECconnectACL>>& for further details.
.option acl_smtp_data main string&!! unset
.cindex "DATA" "ACL for"
This option defines the ACL that is run after an SMTP DATA command has been
processed and the message itself has been received, but before the final
-acknowledgment is sent. See chapter &<<CHAPACL>>& for further details.
+acknowledgment is sent. See section &<<SECdataACLS>>& for further details.
.option acl_smtp_data_prdr main string&!! accept
.cindex "PRDR" "ACL for"
if the PRDR feature has been negotiated,
is run for each recipient after an SMTP DATA command has been
processed and the message itself has been received, but before the
-acknowledgment is sent. See chapter &<<CHAPACL>>& for further details.
+acknowledgment is sent. See section &<<SECTPRDRACL>>& for further details.
.option acl_smtp_dkim main string&!! unset
.cindex DKIM "ACL for"
.cindex "EHLO" "ACL for"
.cindex "HELO" "ACL for"
This option defines the ACL that is run when an SMTP EHLO or HELO
-command is received. See chapter &<<CHAPACL>>& for further details.
+command is received. See section &<<SECheloACL>>& for further details.
.option acl_smtp_mail main string&!! unset
.option acl_smtp_mailauth main string&!! unset
.cindex "AUTH" "on MAIL command"
This option defines the ACL that is run when there is an AUTH parameter on
-a MAIL command. See chapter &<<CHAPACL>>& for details of ACLs, and chapter
+a MAIL command.
+See chapter &<<CHAPACL>>& for general information on ACLs, and chapter
&<<CHAPSMTPAUTH>>& for details of authentication.
.option acl_smtp_mime main string&!! unset
.cindex "not-QUIT, ACL for"
This option defines the ACL that is run when an SMTP session
ends without a QUIT command being received.
-See chapter &<<CHAPACL>>& for further details.
+See section &<<SECTNOTQUITACL>>& for further details.
.option acl_smtp_predata main string&!! unset
This option defines the ACL that is run when an SMTP DATA command is
.option acl_smtp_rcpt main string&!! unset
.cindex "RCPT" "ACL for"
This option defines the ACL that is run when an SMTP RCPT command is
-received. See chapter &<<CHAPACL>>& for further details.
+received. See section &<<SECTQUITACL>>& for further details.
.option acl_smtp_starttls main string&!! unset
.cindex "STARTTLS, ACL for"
This option defines the ACL that is run when an SMTP VRFY command is
received. See chapter &<<CHAPACL>>& for further details.
+.new
+.option acl_smtp_wellknown main string&!! unset
+.cindex "WELLKNOWN, ACL for"
+This option defines the ACL that is run when an SMTP WELLKNOWN command is
+received. See section &<<SECTWELLKNOWNACL>>& for further details.
+.wen
+
.option add_environment main "string list" empty
.cindex "environment" "set values"
This option adds individual environment variables that the
See section &<<SECDKIMVFY>>&.
-.option dmarc_forensic_sender main string&!! unset
-.option dmarc_history_file main string unset
-.option dmarc_tld_file main string unset
+.option dmarc_forensic_sender main string&!! unset &&&
+ dmarc_history_file main string unset &&&
+ dmarc_tld_file main string unset
.cindex DMARC "main section options"
These options control DMARC processing.
See section &<<SECDMARC>>& for details.
dns_again_means_nonexist = *.in-addr.arpa
.endd
This option applies to all DNS lookups that Exim does,
-.new
except for TLSA lookups (where knowing about such failures
is security-relevant).
-.wen
It also applies when the
&[gethostbyname()]& or &[getipnodebyname()]& functions give temporary errors,
since these are most likely to be caused by DNS lookup problems. The
.cindex "EHLO" "underscores in"
.cindex "underscore in EHLO/HELO"
This option can be set to a string of rogue characters that are permitted in
-all EHLO and HELO names in addition to the standard letters, digits,
-hyphens, and dots. If you really must allow underscores, you can set
+non-ip-literal EHLO and HELO names in addition to the standard letters, digits,
+hyphens, and dots. For examplem if you really must allow underscores,
+you can set
.code
helo_allow_chars = _
.endd
+This option does not apply to names that look like ip-literals.
Note that the value is one string, not a list.
nowadays the ACL specified by &%acl_smtp_connect%& can also reject incoming
connections immediately.
-.new
If the connection is on a TLS-on-connect port then the TCP connection is
just dropped. Otherwise, an SMTP error is sent first.
-.wen
The ability to give an immediate rejection (either by this option or using an
ACL) is provided for use in unusual cases. Many hosts will just try again,
.code
hosts_connection_nolog = :
.endd
-.new
The hosts affected by this option also do not log "no MAIL in SMTP connection"
lines, as may commonly be produced by a monitoring system.
-.wen
.option hosts_require_alpn main "host list&!!" unset
+.new
+.option limits_advertise_hosts main "host list&!!" *
+.cindex LIMITS "suppressing advertising"
+.cindex "ESMTP extensions" LIMITS
+This option can be used to suppress the advertisement of the SMTP
+LIMITS extension (RFC 9422) to specific hosts.
+If permitted, Exim as a servier will advertise in the EHLO response
+the limit for RCPT commands set by the &%recipients_max%& option (if it is set)
+and the limit for MAIL commands set by the &%smtp_accept_max_per_connection%&
+option.
+.wen
+
.option local_from_check main boolean true
.cindex "&'Sender:'& header line" "disabling addition of"
.cindex "&'From:'& header line" "disabling checking of"
.option localhost_number main string&!! unset
.cindex "host" "locally unique number for"
.cindex "message ids" "with multiple hosts"
+.cindex multiple "systems sharing a spool"
+.cindex "multiple hosts" "sharing a spool"
+.cindex "shared spool directory"
+.cindex "spool directory" sharing
.vindex "&$localhost_number$&"
Exim's message ids are normally unique only within the local host. If
-uniqueness among a set of hosts is required, each host must set a different
+uniqueness among a set of hosts is required
+(eg. because they share a spool directory),
+each host must set a different
value for the &%localhost_number%& option. The string is expanded immediately
after reading the configuration file (so that a number can be computed from the
host name, for example) and the result of the expansion must be a number in the
range 0&--16 (or 0&--10 on operating systems with case-insensitive file
systems). This is available in subsequent string expansions via the variable
-&$localhost_number$&. When &%localhost_number is set%&, the final two
+&$localhost_number$&. When &%localhost_number%& is set, the final four
characters of the message id, instead of just being a fractional part of the
time, are computed from the time and the local host number as described in
section &<<SECTmessiden>>&.
The option is available only if Exim has been built with Oracle support.
-.new
.option panic_coredump main boolean false
This option is rarely needed but can help for some debugging investigations.
If set, when an internal error is detected by Exim which is sufficient
Note that most systems require additional administrative configuration
to permit write a core file for a setuid program, which is Exim's
common installed configuration.
-.wen
.option percent_hack_domains main "domain list&!!" unset
.cindex "&""percent hack""&"
option was not set.
-.option recipients_max main integer 50000
+.option recipients_max main integer&!! 50000
.cindex "limit" "number of recipients"
.cindex "recipient" "maximum number"
-If this option is set greater than zero, it specifies the maximum number of
+If the value resulting from expanding this option
+is set greater than zero, it specifies the maximum number of
original recipients for any message. Additional recipients that are generated
by aliasing or forwarding do not count. SMTP messages get a 452 response for
all recipients over the limit; earlier recipients are delivered as normal.
Non-SMTP messages with too many recipients are failed, and no deliveries are
done.
+.new
+For SMTP message the expansion is done after the connection is
+accepted (but before any SMTP conversation) and may depend on
+the IP addresses and port numbers of the connection.
+&*Note*&: If an expansion is used for the option,
+care should be taken that a resonable value results for
+non-SMTP messages.
+.wen
+
.cindex "RCPT" "maximum number of incoming"
&*Note*&: The RFCs specify that an SMTP server should accept at least 100
RCPT commands in a single message.
smtp_banner = $smtp_active_hostname ESMTP Exim \
$version_number $tod_full
.endd
-.new
Failure to expand the string causes a panic error;
a forced fail just closes the connection.
-.wen
If you want to create a
multiline response to the initial SMTP connection, use &"\n"& in the string at
appropriate points, but not at the end. Note that the 220 code is not included
&%tls_require_ciphers%& option).
After expansion it must contain
-.new
one or (only for OpenSSL versiona 1.1.1 onwards) more
-.wen
EC curve names, such as &`prime256v1`&, &`secp384r1`&, or &`P-521`&.
Consult your OpenSSL manual for valid curve names.
&`auto`& selects &`prime256v1`&. For more recent OpenSSL versions
&`auto`& tells the library to choose.
-.new
If the option expands to an empty string, the effect is undefined.
-.wen
.option tls_ocsp_file main string&!! unset
See also &%bounce_message_file%&.
+.new
+.option wellknown_advertise_hosts main boolean unset
+.cindex WELLKNOWN advertisement
+.cindex "ESMTP extensions" WELLKNOWN
+This option enables the advertising of the SMTP WELLKNOWN extension.
+See also the &%acl_smtp_wellknown%& ACL (&<<SECTWELLKNOWNACL>>&).
+.wen
+
.option write_rejectlog main boolean true
.cindex "reject log" "disabling"
If this option is set false, Exim no longer writes anything to the reject log.
When the message is about to be written out, the command specified by
&%transport_filter%& is started up in a separate, parallel process, and
the entire message, including the header lines, is passed to it on its standard
-input (this in fact is done from a third process, to avoid deadlock). The
-command must be specified as an absolute path.
+input (this in fact is done from a third process, to avoid deadlock).
+The command must be specified as an absolute path.
+
+The process run by the command must use its standard input as the message
+data to be transformed, and write the results on its standard output.
The lines of the message that are written to the transport filter are
terminated by newline (&"\n"&). The message is passed to the filter before any
.cindex "transports" "&(lmtp)&"
.cindex "&(lmtp)& transport"
.cindex "LMTP" "over a pipe"
-.cindex "LMTP" "over a socket"
+.cindex "LMTP" "over a unix-domain socket"
The &(lmtp)& transport runs the LMTP protocol (RFC 2033) over a pipe to a
specified command
or by interacting with a Unix domain socket.
No part of the resulting command may be tainted.
-.option environment pipe string&!! unset
+.option environment pipe "string list&!!" unset
.cindex "&(pipe)& transport" "environment for command"
.cindex "environment" "&(pipe)& transport"
This option is used to add additional variables to the environment in which the
For testing purposes, this value can be overridden by the &%-oB%& command line
option.
+.new
+.cindex "ESMTP extensions" LIMITS
+If the peer advertises a LIMITS extension with a MAILMAX value,
+and either TLSS is in use or was not advertised,
+that value also constrains the result of this option.
+.wen
+
.option dane_require_tls_ciphers smtp string&!! unset
.cindex "TLS" "requiring specific ciphers for DANE"
Exim can pull out a server name, if there is one, from the response to the
client's SMTP EHLO command.
-The default value of this option:
+For normal STARTTLS use, the default value of this option:
.code
${if and { {match {$host} {.outlook.com\$}} \
{match {$item} {\N^250-([\w.]+)\s\N}} \
} {$1}}
.endd
suffices for one known case.
+
During the expansion of this option the &$item$& variable will have the
server's EHLO response.
+
+.new
+For TLS-on-connect connections we do not have an EHLO
+response to use. Because of this the default value of this option is
+set to a static string for those cases, meaning that resumption will
+always be attempted if permitted by the &%tls_resumption_hosts%& option.
+.wen
+
The result of the option expansion is included in the key used to store and
retrieve the TLS session, for session resumption.
TLS session for any host that matches this list.
&%tls_verify_certificates%& should also be set for the transport.
-.new
The default is &"**"& if DANE is not in use for the connection,
or if DANE-TA us used.
It is empty if DANE-EE is used.
-.wen
.option hosts_require_alpn smtp "host list&!!" unset
.cindex ALPN "require negotiation in client"
.option max_rcpt smtp integer&!! 100
.cindex "RCPT" "maximum number of outgoing"
This option,
-.new
after expansion,
-.wen
limits the number of RCPT commands that are sent in a single
SMTP message transaction.
A value setting of zero disables the limit.
-.new
If a constant is given,
-.wen
each set of addresses is treated independently, and
so can cause parallel connections to the same host if &%remote_max_parallel%&
permits this.
+.new
+.cindex "ESMTP extensions" LIMITS
+If the peer advertises a LIMITS extension with a RCPTMAX value,
+and either TLSS is in use or was not advertised,
+that value also constrains the result of this option
+and no parallel connections will be caused on meeting the RCPTMAX limit.
+.wen
+
.option message_linelength_limit smtp integer 998
.cindex "line length" limit
This option sets the maximum line length, in bytes, that the transport
will send. Any messages with lines exceeding the given value
+(before a transport filter, if any)
will fail and a failure-DSN ("bounce") message will if possible be returned
to the sender.
The default value is that defined by the SMTP standards.
only messages having the domain used for the DANE TLSA lookup are
sent on the connection.
+.new
+.cindex "ESMTP extensions" LIMITS
+If the peer advertises a LIMITS extension with a RCPTDOMAINMAX value,
+and either TLSS is in use or was not advertised,
+this option is regarded as being false.
+.wen
+
+
.option port smtp string&!! "see below"
.cindex "port" "sending TCP/IP"
.cindex "TCP/IP" "setting outgoing port"
deliveries into closed message stores. Exim also has support for running LMTP
over a pipe to a local process &-- see chapter &<<CHAPLMTP>>&.
+.new
+&*Note*&: When using LMTP it should be considered whether the default values
+for some other features, such as DANE, are appropriate.
+.wen
+
If this option is set to &"smtps"&, the default value for the &%port%& option
changes to &"smtps"&, and the transport initiates TLS immediately after
connecting, as an outbound SSL-on-connect, instead of using STARTTLS to upgrade.
Successful authentication sets up information used by the
&%authresults%& expansion item.
-.new
.cindex authentication "failure event, server"
If an authenticator is run and does not succeed,
an event (see &<<CHAPevents>>&) of type "auth:fail" is raised.
If the event is serviced and a string is returned then the string will be logged
instead of the default log line.
See <<CHAPevents>> for details on events.
-.wen
.section "Testing server authentication" "SECID169"
try again later. If there are any backup hosts available, they are tried in the
usual way.
-.new
.next
.cindex authentication "failure event, client"
If the response to authentication is a permanent error (5&'xx'& code),
will be valid.
If the event is serviced and a string is returned then the string will be logged.
See <<CHAPevents>> for details on events.
-.wen
.next
If the response to authentication is a permanent error (5&'xx'& code), Exim
server_set_id = $auth1
.endd
-.new
&*Note*&: plaintext authentication methods such as PLAIN and LOGIN
should not be advertised on cleartext SMTP connections.
See the discussion in section &<<SECTplain_TLS>>&.
-.wen
If the SMTP connection is encrypted, or if &$sender_host_address$& is equal to
&$received_ip_address$& (that is, the connection is local), the &"secured"&
(If an API is found to let OpenSSL be configured in this way,
let the Exim Maintainers know and we'll likely use it).
.next
-With GnuTLS, if an explicit list is used for the &%tls_privatekey%& main option
-main option, it must be ordered to match the &%tls_certificate%& list.
+With GnuTLS, if an explicit list is used for the &%tls_privatekey%& main option,
+it must be ordered to match the &%tls_certificate%& list.
.next
Some other recently added features may only be available in one or the other.
This should be documented with the feature. If the documentation does not
.subsection General
Under GnuTLS, DANE is only supported from version 3.0.0 onwards.
-DANE is specified in published RFCs and decouples certificate authority trust
+DANE is specified in RFC 6698. It decouples certificate authority trust
selection from a "race to the bottom" of "you must trust everything for mail
to get through".
-There is an alternative technology called MTA-STS, which
-instead publishes MX trust anchor information on an HTTPS website. At the
-time this text was last updated, MTA-STS was still a draft, not yet an RFC.
+It does retain the need to trust the assurances provided by the DNSSEC tree.
+
+There is an alternative technology called MTA-STS (RFC 8461), which
+instead publishes MX trust anchor information on an HTTPS website.
+The discovery of the address for that website does not (per standard)
+require DNSSEC, and could be regarded as being less secure than DANE
+as a result.
+
Exim has no support for MTA-STS as a client, but Exim mail server operators
can choose to publish information describing their TLS configuration using
MTA-STS to let those clients who do use that protocol derive trust
.cindex "RCPT" "ACL for"
.cindex "STARTTLS, ACL for"
.cindex "VRFY" "ACL for"
+.cindex "WELLKNOWN" "ACL for"
.cindex "SMTP" "connection, ACL for"
.cindex "non-SMTP messages" "ACLs for"
.cindex "MIME content scanning" "ACL for"
.irow &%acl_smtp_rcpt%& "ACL for RCPT"
.irow &%acl_smtp_starttls%& "ACL for STARTTLS"
.irow &%acl_smtp_vrfy%& "ACL for VRFY"
+.irow &%acl_smtp_wellknown%& "ACL for WELLKNOWN"
.endtable
For example, if you set
testing as possible at RCPT time.
-.subsection "The non-SMTP ACLs" SECID190
+.subsection "The non-SMTP ACLs" SECnonSMTP
.cindex "non-SMTP messages" "ACLs for"
The non-SMTP ACLs apply to all non-interactive incoming messages, that is, they
apply to batched SMTP as well as to non-SMTP messages. (Batched SMTP is not
temporary error for these kinds of message.
-.subsection "The SMTP connect ACL" SECID191
+.subsection "The SMTP connect ACL" SECconnectACL
.cindex "SMTP" "connection, ACL for"
.oindex &%smtp_banner%&
The ACL test specified by &%acl_smtp_connect%& happens at the start of an SMTP
the message override the banner message that is otherwise specified by the
&%smtp_banner%& option.
-.new
For tls-on-connect connections, the ACL is run before the TLS connection
is accepted; if the ACL does not accept then the TCP connection is dropped without
any TLS startup attempt and without any SMTP response being transmitted.
-.wen
-.subsection "The EHLO/HELO ACL" SECID192
+.subsection "The EHLO/HELO ACL" SECheloACL
.cindex "EHLO" "ACL for"
.cindex "HELO" "ACL for"
The ACL test specified by &%acl_smtp_helo%& happens when the client issues an
an EHLO response.
-.subsection "The DATA ACLs" SECID193
+.subsection "The DATA ACLs" SECdataACLS
.cindex "DATA" "ACLs for"
Two ACLs are associated with the DATA command, because it is two-stage
command, with two responses being sent to the client.
The &%acl_smtp_dkim%& ACL is available only when Exim is compiled with DKIM support
enabled (which is the default).
+If, for a specific message, an ACL control
+&*dkim_disable_verify*&
+has been set, this &%acl_smtp_dkim%& ACL is not called.
+
The ACL test specified by &%acl_smtp_dkim%& happens after a message has been
received, and is executed for each DKIM signature found in a message. If not
otherwise specified, the default action is to accept.
If the ACL is not defined, processing completes as if
the feature was not requested by the client.
+.new
+.subsection "The SMTP WELLKNOWN ACL" SECTWELLKNOWNACL
+.cindex "WELLKNOWN" "ACL for"
+.oindex "&%acl_smtp_wellknown%&"
+The &%acl_smtp_wellknown%& ACL is available only when Exim is compiled
+with WELLKNOWN support enabled.
+
+The ACL determines the response to an SMTP WELLKNOWN command, using the normal
+accept/defer/deny verbs for the response code,
+and a new &"control=wellknown"& modifier.
+This modifier takes a single option, separated by a '/'
+character, which must be the name of a file containing the response
+cleartext. The modifier is expanded before use in the usual way before
+it is used. The configuration is responsible for picking a suitable file
+to return and, most importantly, not returning any unexpected file.
+The argument for the SMTP verb will be available in the &$smtp_command_argument$&
+variable and can be used for building the file path.
+If the file path given in the modifier is empty or inacessible, the control will
+fail.
+
+For example:
+.code
+ check_wellknown:
+ accept control = wellknown/\
+ ${lookup {${xtextd:$smtp_command_argument}} \
+ dsearch,key=path,filter=file,ret=full \
+ {$spooldir/wellknown.d}}
+.endd
+File content will be encoded in &"xtext"& form, and line-wrapping
+for line-length limitation will be done before transmission.
+A response summary line will be prepended, with the (pre-encoding) file size.
+
+The above example uses the expansion operator ${xtextd:<coded-string>}
+which is needed to decode the xtext-encoded key from the SMTP verb.
+
+Under the util directory there is a "mailtest" utility which can be used
+to test/retrieve WELLKNOWN items. Syntax is
+.code
+ mailtest -h host.example.com -w security.txt
+.endd
+
+WELLKNOWN is a ESMTP extension providing access to extended
+information about the server. It is modelled on the webserver
+facilities documented in RFC 8615 and can be used for a security.txt
+file and could be used for ACME handshaking (RFC 8555).
+
+Exim will advertise WELLKNOWN support in the EHLO response
+.oindex &%wellknown_advertise_hosts%&
+(conditional on a new option &%wellknown_advertise_hosts%&)
+and service WELLKNOWN smtp verbs having a single parameter
+giving a key for an item of "site-wide metadata".
+The verb and key are separated by whitespace,
+and the key is xtext-encoded (per RFC 3461 section 4).
+.wen
+
+
.subsection "The QUIT ACL" SECTQUITACL
.cindex "QUIT, ACL for"
The ACL for the SMTP QUIT command is anomalous, in that the outcome of the ACL
&%acl_smtp_mime%&, &%acl_smtp_predata%&, and &%acl_smtp_starttls%&, the action
when the ACL is not defined is &"accept"&.
-For the others (&%acl_smtp_etrn%&, &%acl_smtp_expn%&, &%acl_smtp_rcpt%&, and
-&%acl_smtp_vrfy%&), the action when the ACL is not defined is &"deny"&.
-This means that &%acl_smtp_rcpt%& must be defined in order to receive any
-messages over an SMTP connection. For an example, see the ACL in the default
-configuration file.
-
+For the others (&%acl_smtp_etrn%&, &%acl_smtp_expn%&, &%acl_smtp_rcpt%&,
+&%acl_smtp_vrfy%&
+.new
+and &%acl_smtp_wellknown%&),
+.wen
+the action when the ACL
+is not defined is &"deny"&. This means that &%acl_smtp_rcpt%& must be
+defined in order to receive any messages over an SMTP connection.
+For an example, see the ACL in the default configuration file.
.section "Format of an ACL" "SECID199"
.cindex "&ACL;" "format of"
.cindex "&ACL;" "verbs, definition of"
-An individual ACL consists of a number of statements. Each statement starts
+An individual ACL definition consists of a number of statements.
+Each statement starts
with a verb, optionally followed by a number of conditions and &"modifiers"&.
Modifiers can change the way the verb operates, define error and log messages,
set variables, insert delays, and vary the processing of accepted messages.
all the conditions make sense at every testing point. For example, you cannot
test a sender address in the ACL that is run for a VRFY command.
+The definition of an ACL ends where another starts,
+or a different configuration section starts.
+
.section "ACL verbs" "SECID200"
The ACL verbs are as follows:
This control enables conversion of UTF-8 in message envelope addresses
to a-label form.
For details see section &<<SECTi18nMTA>>&.
+
+.new
+.vitem &*control&~=&~wellknown*&
+This control sets up a response data file for a WELLKNOWN SMTP command.
+It may only be used in an ACL servicing that command.
+For details see section &<<SECTWELLKNOWNACL>>&.
+.wen
.endlist vlist
More than one header can be removed at the same time by using a colon separated
list of header specifiers.
-.new
If a specifier does not start with a circumflex (^)
then it is treated as a header name.
The header name matching is case insensitive.
.code
remove_header = \N^(?i)Authentication-Results\s*::\s*example.org;\N
.endd
-.wen
List expansion is not performed, so you cannot use hostlists to
create a list of headers, however both connection and message variable expansion
filename, and the default path is then used.
.endlist
The &%decode%& condition normally succeeds. It is only false for syntax
-errors or unusual circumstances such as memory shortages. You can easily decode
-a file with its original, proposed filename using
-.code
-decode = $mime_filename
-.endd
-However, you should keep in mind that &$mime_filename$& might contain
-anything. If you place files outside of the default path, they are not
+errors or unusual circumstances such as memory shortages.
+.new
+The variable &$mime_filename$& will have the suggested name for the file.
+Note however that this might contain anything, and is very difficult
+to safely use as all or even part of the filename.
+.wen
+If you place files outside of the default path, they are not
automatically unlinked.
For RFC822 attachments (these are messages attached to messages, with a
(the -D file). The file is open for reading and writing, but updating it is not
recommended. &*Warning*&: You must &'not'& close this file descriptor.
-The descriptor is positioned at character 19 of the file, which is the first
-character of the body itself, because the first 19 characters are the message
-id followed by &`-D`& and a newline. If you rewind the file, you should use the
+The descriptor is positioned at character 26 of the file, which is the first
+character of the body itself, because the first 26 characters (19 characters
+before Exim 4.97) are the message id followed by &`-D`& and a newline.
+If you rewind the file, you should use the
macro SPOOL_DATA_START_OFFSET to reset to the start of the data, just in
case this changes in some future version.
.next
follows:
.ilist
-LF not preceded by CR is treated as a line ending.
-.next
CR is treated as a line ending; if it is immediately followed by LF, the LF
is ignored.
.next
.next
If the first header line received in a message ends with CRLF, a subsequent
bare LF in a header line is treated in the same way as a bare CR in a header
-line.
+line and a bare LF in a body line is replaced with a space.
+.next
+If the first header line received in a message does not end with CRLF, a subsequent
+LF not preceded by CR is treated as a line ending.
.endlist
.irow &`deliver_time`& "time taken to attempt delivery"
.irow &`delivery_size`& "add &`S=`&&'nnn'& to => lines"
.irow &`dkim`& * "DKIM verified domain on <= lines"
-.irow &`dkim_verbose`& "separate full DKIM verification result line, per signature"
+.irow &`dkim_verbose`& "separate full DKIM verification result line, per signature; DKIM signing"
.irow &`dnslist_defer`& * "defers of DNS list (aka RBL) lookups"
.irow &`dnssec`& "DNSSEC secured lookups"
.irow &`etrn`& * "ETRN commands"
.irow &`tls_peerdn`& "TLS peer DN on <= and => lines"
.irow &`tls_resumption`& "append * to cipher field"
.irow &`tls_sni`& "TLS SNI on <= lines"
-.irow &`unknown_in_list`& "DNS lookup failed in list match"
+.irow &`unknown_in_list`& "lookup failed in list match"
.irow &`all`& "&*all of the above*&"
.endtable
See also the &%slow_lookup_log%& main configuration option,
between the caller and Exim.
.next
.cindex "log" "connection identifier"
-.new
&%connection_identifier%&: An identifier for the accepted connection is added to
connection start and end lines and to message accept lines.
The identifier is tagged by Ci=.
The value is PID-based, so will reset on reboot and will wrap.
-.wen
.next
.cindex "log" "connection rejections"
&%connection_reject%&: A log entry is written whenever an incoming SMTP
.cindex log "DKIM verification"
.cindex DKIM "verification logging"
&%dkim_verbose%&: A log entry is written for each attempted DKIM verification.
+.new
+Also, on message delivery lines signing information (domain and selector)
+is added, tagged with DKIM=.
+.wen
.next
.cindex "log" "dnslist defer"
.cindex "DNS list" "logging defer"
.next
.cindex "log" "DNS failure in list"
&%unknown_in_list%&: This setting causes a log entry to be written when the
-result of a list match is failure because a DNS lookup failed.
+result of a list match is failure because a DNS lookup failed, or because
+a bad IP address was in the list.
.endlist
.olist
Signing outgoing messages: This function is implemented in the SMTP transport.
It can co-exist with all other Exim features
-(including transport filters)
-except cutthrough delivery.
+(including transport filters) except cutthrough delivery.
+.new
+However, signing options may not depend on headers modified by
+routers, the transport or a transport filter.
+.wen
.next
Verifying signatures in incoming messages: This is implemented by an additional
ACL (acl_smtp_dkim), which can be called several times per message, with
.option dkim_sign_headers smtp string&!! "see below"
If set, this option must expand to a colon-separated
list of header names.
-Headers with these names, or the absence or such a header, will be included
+Headers with these names, or the absence of such a header, will be included
in the message signature.
When unspecified, the header names listed in RFC4871 will be used,
whether or not each header is present in the message.
.option dkim_timestamps smtp integer&!! unset
This option controls the inclusion of timestamp information in the signature.
If not set, no such information will be included.
-Otherwise, must be an unsigned number giving an offset in seconds from the current time
-for the expiry tag
-(eg. 1209600 for two weeks);
-both creation (t=) and expiry (x=) tags will be included.
+.new
+Otherwise, must be an unsigned number giving an offset in seconds from the
+current time for the expiry tag (e.g. 1209600 for two weeks); both creation
+(t=) and expiry (x=) tags will be included unless the offset is 0 (no expiry).
+.wen
RFC 6376 lists these tags as RECOMMENDED.
Verification of DKIM signatures in SMTP incoming email is done for all
messages for which an ACL control &%dkim_disable_verify%& has not been set.
+
.cindex DKIM "selecting signature algorithms"
-Individual classes of signature algorithm can be ignored by changing
+Individual classes of DKIM signature algorithm can be ignored by changing
the main options &%dkim_verify_hashes%& or &%dkim_verify_keytypes%&.
The &%dkim_verify_minimal%& option can be set to cease verification
processing for a message once the first passing signature is found.
of this section can be ignored.
The results of verification are made available to the
-&%acl_smtp_dkim%& ACL, which can examine and modify them.
+&%acl_smtp_dkim%& ACL, which (for complex needs) can examine and modify them.
A missing ACL definition defaults to accept.
By default, the ACL is called once for each
syntactically(!) correct signature in the incoming message.
&%dkim_verify_signers%& (see above).
.vitem &%$dkim_verify_status%&
+So long as a DKIM ACL is defined
+(it need do no more than accept, which is the default),
+after all the DKIM ACL runs have completed, the value becomes a
+colon-separated list of the values after each run.
+The value is maintained for the MIME, PRDR and DATA ACLs.
+
Within the DKIM ACL,
a string describing the general status of the signature. One of
.ilist
set dkim_verify_reason = hash too weak or key too short
.endd
-So long as a DKIM ACL is defined (it need do no more than accept),
-after all the DKIM ACL runs have completed, the value becomes a
-colon-separated list of the values after each run.
-This is maintained for the mime, prdr and data ACLs.
-
.vitem &%$dkim_verify_reason%&
A string giving a little bit more detail when &%$dkim_verify_status%& is either
"fail" or "invalid". One of
.endlist
-In addition, two ACL conditions are provided, usable only in a DKIM ACL:
+In addition, two ACL conditions are provided:
.vlist
.vitem &%dkim_signers%&
ACL condition that checks a colon-separated list of domains or identities
for a match against the domain or identity that the ACL is currently verifying
-(reflected by &%$dkim_cur_signer%&). This is typically used to restrict an ACL
+(reflected by &%$dkim_cur_signer%&).
+This condition is only usable in a DKIM ACL.
+This is typically used to restrict an ACL
verb to a group of domains or identities. For example:
.code
.vitem &%dkim_status%&
ACL condition that checks a colon-separated list of possible DKIM verification
-results against the actual result of verification. This is typically used
+results against the actual result of verification,
+given by &$dkim_verify_status$& if that is non-empty or "none" if empty.
+.new
+This condition may be used in DKIM, MIME, PRDR and DATA ACLs.
+.wen
+
+A basic verification might be:
+.code
+deny !dkim_status = pass:none:invalid
+.endd
+
+A more complex use could be
to restrict an ACL verb to a list of verification outcomes, for example:
.code
The possible status keywords are: 'none','invalid','fail' and 'pass'. Please
see the documentation of the &%$dkim_verify_status%& expansion variable above
for more information of what they mean.
+
+The condition is true if the status
+.new
+(or any of the list of status values)
+.wen
+is any one of the supplied list.
.endlist
.subsection "SRS (Sender Rewriting Scheme)" SECTSRS
.cindex SRS "sender rewriting scheme"
+.cindex VERP "variable envelope return path"
SRS can be used to modify sender addresses when forwarding so that
SPF verification does not object to them.
-It operates by encoding the original envelope sender in a new
+It can also be used to identify a received bounce message as
+likely (or not) having been trigged by a message from the
+local system, and for identifying dead addresses in mailing lists.
+It is one implementation of a VERP (Variable Envelope Return Path) method.
+
+SRS operates by encoding the original envelope sender in a new
sender local part and using a domain run by the forwarding site
as the new domain for the sender. Any DSN message should be returned
to this new sender at the forwarding site, which can extract the
If it is, the condition will return true and the variable
&$srs_recipient$& will be set to the decoded (original) value.
-.new
If the second argument is empty then the condition returns true if
the first argument is in valid SRS formet, else false.
The variable &$srs_recipient$& is not set for this case.
-.wen
.endlist
Example usage:
allow_fail
data = :fail: Invalid SRS recipient address
- #... further routers here
+ #... further routers here get inbound_srs-redirected recipients
+ # and any that were not SRS'd
# transport; should look like the non-forward outbound
The name is placed in the variable &$event_name$& and the event action
expansion must check this, as it will be called for every possible event type.
+.new
The current list of events is:
+.wen
.itable all 0 0 4 25* left 10* center 15* center 50* left
.row auth:fail after both "per driver per authentication attempt"
.row dane:fail after transport "per connection"
+.row dns:fail after both "per lookup"
.row msg:complete after main "per message"
.row msg:defer after transport "per message per delivery try"
.row msg:delivery after transport "per recipient"
.itable all 0 0 2 20* left 80* left
.row auth:fail "smtp response"
.row dane:fail "failure reason"
+.row dns:fail "failure reason, key and lookup-type"
.row msg:defer "error string"
.row msg:delivery "smtp confirmation message"
.row msg:fail:internal "failure reason"
no other use is made of it.
For a tcp:connect event, if the connection is being made to a proxy
-then the address and port variables will be that of the proxy and not
-the target system.
+then the &$host_address$& and &$host_port$& variables
+will be that of the proxy and not the target system.
For tls:cert events, if GnuTLS is in use this will trigger only per
chain element received on the connection.
For OpenSSL it will trigger for every chain element including those
loaded locally.
+.new
+For dns:fail events from dnsdb lookups, a &"defer_never"& option does not
+affect the reporting of DNS_AGAIN.
+.wen
+
. ////////////////////////////////////////////////////////////////////////////
. ////////////////////////////////////////////////////////////////////////////
git://git.exim.org / exim.git / blobdiff