-$Cambridge: exim/doc/doc-txt/ChangeLog,v 1.286 2006/02/07 16:36:25 ph10 Exp $
+$Cambridge: exim/doc/doc-txt/ChangeLog,v 1.317 2006/03/01 10:40:03 ph10 Exp $
Change log file for Exim from version 4.21
-------------------------------------------
address records were *not* found in the additional section, the port
values from the SRV records were lost.
+PH/17 If a delivery to a pipe, file, or autoreply was deferred, Exim was not
+ using the correct key (the original address) when searching the retry
+ rules in order to find which one to use for generating the retry hint.
+
+PH/18 If quota_warn_message contains a From: header, Exim now refrains from
+ adding the default one. Similarly, if it contains a Reply-To: header, the
+ errors_reply_to option, if set, is not used.
+
+PH/19 When calculating a retry time, Exim used to measure the "time since
+ failure" by looking at the "first failed" field in the retry record. Now
+ it does not use this if it is later than than the arrival time of the
+ message. Instead it uses the arrival time. This makes for better
+ behaviour in cases where some deliveries succeed, thus re-setting the
+ "first failed" field. An example is a quota failure for a huge message
+ when small messages continue to be delivered. Without this change, the
+ "time since failure" will always be short, possible causing more frequent
+ delivery attempts for the huge message than are intended.
+
+PH/20 Added $auth1, $auth2, $auth3 to contain authentication data (as well as
+ $1, $2, $3) because the numerical variables can be reset during some
+ expansion items (e.g. "match"), thereby losing the authentication data.
+
+PH/21 Make -bV show the size of off_t variables so that the test suite can
+ decide whether to run tests for quotas > 2G.
+
+PH/22 Test the values given for quota, quota_filecount, quota_warn_threshold,
+ mailbox_size, and mailbox_filecount in the appendfile transport. If a
+ filecount value is greater than 2G or if a quota value is greater than 2G
+ on a system where the size of off_t is not greater than 4, a panic error
+ is given.
+
+PH/23 When a malformed item such as 1.2.3/24 appears in a host list, it can
+ never match. The debug and -bh output now contains an explicit error
+ message indicating a malformed IPv4 address or mask.
+
+PH/24 An host item such as 1.2.3.4/abc was being treated as the IP address
+ 1.2.3.4 without a mask. Now it is not recognized as an IP address, and
+ PH/23 above applies.
+
+PH/25 Do not write to syslog when running in the test harness. The only
+ occasion when this arises is a failure to open the main or panic logs
+ (for which there is an explicit test).
+
+PH/26 Added the /no_tell option to "control=freeze".
+
+PH/27 If a host name lookup failed very early in a connection, for example, if
+ the IP address matched host_lookup and the reverse lookup yielded a name
+ that did not have a forward lookup, an error message of the form "no IP
+ address found for host xxx.xxx.xxx (during SMTP connection from NULL)"
+ could be logged. Now it outputs the IP address instead of "NULL".
+
+PH/28 An enabling patch from MH: add new function child_open_exim2() which
+ allows the sender and the authenticated sender to be set when
+ submitting a message from within Exim. Since child_open_exim() is
+ documented for local_scan(), the new function should be too.
+
+PH/29 In GnuTLS, a forced expansion failure for tls_privatekey was not being
+ ignored. In both GnuTLS and OpenSSL, an expansion of tls_privatekey that
+ results in an empty string is now treated as unset.
+
+PH/30 Fix eximon buffer overflow bug (Bugzilla #73).
+
+PH/31 Added sender_verify_fail logging option.
+
+PH/32 In November 2003, the code in Exim that added an empty Bcc: header when
+ needed by RFC 822 but not by RFC 2822 was commented out. I have now
+ tidied the source and removed it altogether.
+
+PH/33 When a queue run was abandoned because the load average was too high, a
+ log line was always written; now it is written only if the queue_run log
+ selector is set. In addition, the log line for abandonment now contains
+ information about the queue run such as the pid. This is always present
+ in "start" and "stop" lines but was omitted from the "abandon" line.
+
+PH/34 Omit spaces between a header name and the colon in the error message that
+ is given when verify = headers_syntax fails (if there are lots of them,
+ the message gets confusing).
+
+PH/35 Change the default for dns_check_names_pattern to allow slashes within
+ names, as there are now some PTR records that contain slashes. This check
+ is only to protect against broken name servers that fall over on strange
+ characters, so the fact that it applies to all lookups doesn't matter.
+
+PH/36 Now that the new test suite is complete, we can remove some of the
+ special code in Exim that was needed for the old test suite. For example,
+ sorting DNS records because real resolvers return them in an arbitrary
+ order. The new test suite's fake resolver always returns records in the
+ same order.
+
+PH/37 When running in the test harness, use -odi for submitted messages (e.g.
+ bounces) except when queue_only is set, to avoid logging races between
+ the different processes.
+
+PH/38 Panic-die if .include specifies a non-absolute path.
+
+PH/39 A tweak to the "H" retry rule from its user.
+
+JJ/03 exipick: Removed parentheses from 'next' and 'last' calls that specified
+ a label. They prevented compilation on older perls.
+
+JJ/04 exipick: Refactored code to prevent implicit split to @_ which caused
+ a warning to be raised on newish perls.
+
+JJ/05 exipick: Fixed bug where -bpc always showed a count of all messages
+ on queue. Changes to match documented behaviour of showing count of
+ messages matching specified criteria.
+
+PH/40 Changed the default ident timeout from 30s to 5s.
+
+PH/41 Added support for the use of login_cap features, on those BSD systems
+ that have them, for controlling the resources used by pipe deliveries.
+
+PH/42 The content-scanning code uses fopen() to create files in which to put
+ message data. Previously it was not paying any attention to the mode of
+ the files. Exim runs with umask(0) because the rest of the code creates
+ files with open(), and sets the required mode explicitly. Thus, these
+ files were ending up world-writeable. This was not a big issue, because,
+ being within the spool directory, they were not world-accessible. I have
+ created a function called modefopen, which takes an additional mode
+ argument. It sets umask(777), creates the file, chmods it to the required
+ mode, then resets the umask. All the relevant calls to fopen() in the
+ content scanning code have been changed to use this function.
+
+PH/43 If retry_interval_max is set greater than 24 hours, it is quietly reset
+ to 24 hours. This avoids potential overflow problems when processing G
+ and H retry rules. I suspect nobody ever tinkers with this value.
+
+PH/44 Added STRIP_COMMAND=/usr/bin/strip to the FreeBSD Makefile.
+
+PH/45 When the plaintext authenticator is running as a client, the server's
+ challenges are checked to ensure they are valid base64 strings. By
+ default, the authentication attempt is cancelled if an invalid string is
+ received. Setting client_ignore_invalid_base64 true ignores these errors.
+ The decoded challenge strings are now placed in $auth1, $auth2, etc. as
+ they are received. Thus, the responses can be made to depend on the
+ challenges. If an invalid string is ignored, an empty string is placed in
+ the variable.
+
+PH/46 Messages that are created by the autoreply transport now contains a
+ References: header, in accordance with RFCs 2822 and 3834.
+
+PH/47 Added authenticated_sender_force to the smtp transport.
+
+PH/48 The ${prvs expansion was broken on systems where time_t was long long.
+
+PH/49 Installed latest patch from the Sieve maintainer.
Exim version 4.60
git://git.exim.org / exim.git / blobdiff