.cindex "incorporated code"
.cindex "regular expressions" "library"
.cindex "PCRE"
+.cindex "OpenDMARC"
A number of pieces of external code are included in the Exim distribution.
.ilist
SOFTWARE.
.endblockquote
+.next
+.cindex "opendmarc" "acknowledgment"
+The DMARC implementation uses the OpenDMARC library which is Copyrighted by
+The Trusted Domain Project. Portions of Exim source which use OpenDMARC
+derived code are indicated in the respective source files. The full OpenDMARC
+license is provided in the LICENSE.opendmarc file contained in the distributed
+source code.
+
.next
Many people have contributed code fragments, some large, some small, that were
not covered by any specific licence requirements. It is assumed that the
It sets the incoming protocol and host name (for trusted callers). The
host name and its colon can be omitted when only the protocol is to be set.
Note the Exim already has two private options, &%-pd%& and &%-ps%&, that refer
-to embedded Perl. It is therefore impossible to set a protocol value of &`p`&
+to embedded Perl. It is therefore impossible to set a protocol value of &`d`&
or &`s`& using this option (but that does not seem a real limitation).
.vitem &%-q%&
be useful for processing the output of the MD5 and SHA-1 hashing functions.
+
+.vitem &*${hexquote:*&<&'string'&>&*}*&
+.cindex "quoting" "hex-encoded unprintable characters"
+.cindex "&%hexquote%& expansion item"
+This operator converts non-printable characters in a string into a hex
+escape form. Byte values between 33 (!) and 126 (~) inclusive are left
+as is, and other byte values are converted to &`\xNN`&, for example a
+byt value 127 is converted to &`\x7f`&.
+
+
.vitem &*${lc:*&<&'string'&>&*}*&
.cindex "case forcing in strings"
.cindex "string" "case forcing"
avoids any problems with spaces or shell metacharacters, and is of use when a
&(pipe)& transport is handling groups of addresses in a batch.
-If &(force_command)& is enabled on the transport, Special handling takes place
+If &%force_command%& is enabled on the transport, Special handling takes place
for an argument that consists of precisely the text &`$address_pipe`&. It
-is handled much like &`$pipe_addresses`& above. It is expanded and each
+is handled similarly to &$pipe_addresses$& above. It is expanded and each
argument is inserted in the argument list at that point
-&'as a separate argument'&.
+&'as a separate argument'&. The &`$address_pipe`& item does not need to be
+the only item in the argument; in fact, if it were then &%force_command%&
+should behave as a no-op. Rather, it should be used to adjust the command
+run while preserving the argument vector separation.
After splitting up into arguments and expansion, the resulting command is run
in a subprocess directly from the transport, &'not'& under a shell. The
force_command
.endd
+Note that &$address_pipe$& is handled specially in &%command%& when
+&%force_command%& is set, expanding out to the original argument vector as
+separate items, similarly to a Unix shell &`"$@"`& construct.
+
.option ignore_status pipe boolean false
If this option is true, the status returned by the subprocess that is set up to
run the command is ignored, and Exim behaves as if zero had been returned.
.cindex "&%set%& ACL modifier"
This modifier puts a value into one of the ACL variables (see section
&<<SECTaclvariables>>&).
+
+
+.vitem &*udpsend*&&~=&~<&'parameters'&>
+This modifier sends a UDP packet, for purposes such as statistics
+collection or behaviour monitoring. The parameters are expanded, and
+the result of the expansion must be a colon-separated list consisting
+of a destination server, port number, and the packet contents. The
+server can be specified as a host name or IPv4 or IPv6 address. The
+separator can be changed with the usual angle bracket syntax. For
+example, you might want to collect information on which hosts connect
+when:
+.code
+udpsend = <; 2001:dB8::dead:beef ; 1234 ;\
+ $tod_zulu $sender_host_address
+.endd
.endlist
LHLO is used instead of HELO if the transport's &%protocol%& option is
set to &"lmtp"&.
+The callout may use EHLO, AUTH and/or STARTTLS given appropriate option
+settings.
+
A recipient callout check is similar. By default, it also uses an empty address
for the sender. This default is chosen because most hosts do not make use of
the sender address when verifying a recipient. Using the same address means
+.section "Running local commands" "SECTsecconslocalcmds"
+There are a number of ways in which an administrator can configure Exim to run
+commands based upon received, untrustworthy, data. Further, in some
+configurations a user who can control a &_.forward_& file can also arrange to
+run commands. Configuration to check includes, but is not limited to:
+
+.ilist
+Use of &%use_shell%& in the pipe transport: various forms of shell command
+injection may be possible with this option present. It is dangerous and should
+be used only with considerable caution. Consider constraints which whitelist
+allowed characters in a variable which is to be used in a pipe transport that
+has &%use_shell%& enabled.
+.next
+A number of options such as &%forbid_filter_run%&, &%forbid_filter_perl%&,
+&%forbid_filter_dlfunc%& and so forth which restrict facilities available to
+&_.forward_& files in a redirect router. If Exim is running on a central mail
+hub to which ordinary users do not have shell access, but home directories are
+NFS mounted (for instance) then administrators should review the list of these
+forbid options available, and should bear in mind that the options that may
+need forbidding can change as new features are added between releases.
+.next
+The &%${run...}%& expansion item does not use a shell by default, but
+administrators can configure use of &_/bin/sh_& as part of the command.
+Such invocations should be viewed with prejudicial suspicion.
+.next
+Administrators who use embedded Perl are advised to explore how Perl's
+taint checking might apply to their usage.
+.next
+Use of &%${expand...}%& is somewhat analagous to shell's eval builtin and
+administrators are well advised to view its use with suspicion, in case (for
+instance) it allows a local-part to contain embedded Exim directives.
+.next
+Use of &%${match_local_part...}%& and friends becomes more dangerous if
+Exim was built with EXPAND_LISTMATCH_RHS defined: the second string in
+each can reference arbitrary lists and files, rather than just being a list
+of opaque strings.
+The EXPAND_LISTMATCH_RHS option was added and set false by default because of
+real-world security vulnerabilities caused by its use with untrustworthy data
+injected in, for SQL injection attacks.
+Consider the use of the &%inlisti%& expansion condition instead.
+.endlist
+
+
+
.section "IPv4 source routing" "SECID272"
.cindex "source routing" "in IP packets"
.cindex "IP source routing"
git://git.exim.org / exim.git / blobdiff