X-Git-Url: https://git.exim.org/users/jgh/exim.git/blobdiff_plain/5ca2a9a1a936ecc55402a1d40b7d8adb74865aba..f331f3b639d802237239c3c3a19883ee89d062b5:/doc/doc-txt/ChangeLog?ds=sidebyside

diff --git a/doc/doc-txt/ChangeLog b/doc/doc-txt/ChangeLog
index 4d7dd8517..20f21b043 100644
--- a/doc/doc-txt/ChangeLog
+++ b/doc/doc-txt/ChangeLog
@@ -1,4 +1,4 @@
-$Cambridge: exim/doc/doc-txt/ChangeLog,v 1.117 2005/04/06 15:26:52 ph10 Exp $
+$Cambridge: exim/doc/doc-txt/ChangeLog,v 1.130 2005/05/03 08:38:13 ph10 Exp $
 
 Change log file for Exim from version 4.21
 -------------------------------------------
@@ -63,8 +63,9 @@ PH/09 Previously, an attempt to use ${perl when it wasn't compiled gave an
 
 PH/10 Added a nasty fudge to try to recognize and flatten LDAP passwords in
       an address' error message when a string expansion fails (syntax or
-      whatever). Otherwise not only does the password appear in the log, it may
-      also be put in a bounce message.
+      whatever). Otherwise the password may appear in the log. Following change
+      PH/42 below, there is no longer a chance of it appearing in a bounce
+      message.
 
 PH/11 Installed exipick version 20050225.0 from John Jetmore.
 
@@ -190,6 +191,81 @@ PH/30 In these circumstances:
       and peerdn, if requested) that were in fact used only for the second
       address.
 
+PH/31 When doing a callout as part of verifying an address, Exim was not paying
+      attention to any local part prefix or suffix that was matched by the
+      router that accepted the address. It now behaves in the same way as it
+      does for delivery: the affixes are removed from the local part unless
+      rcpt_include_affixes is set on the transport.
+
+PH/32 Add the sender address, as F=<...>, to the log line when logging a
+      timeout during the DATA phase of an incoming message.
+
+PH/33 Sieve envelope tests were broken for match types other than :is. I have
+      applied a patch sanctioned by the Sieve maintainer.
+
+PH/34 Change 4.50/80 broke Exim in that it could no longer handle cases where
+      the uid or gid is negative. A case of a negative gid caused this to be
+      noticed. The fix allows for either to be negative.
+
+PH/35 ACL_WHERE_MIME is now declared unconditionally, to avoid too much code
+      clutter, but the tables that are indexed by ACL_WHERE_xxx values had been
+      overlooked.
+
+PH/36 The change PH/12 above was broken. Fixed it.
+
+PH/37 Exim used to check for duplicate addresses in the middle of routing, on
+      the grounds that routing the same address twice would always produce the
+      same answer. This might have been true once, but it is certainly no
+      longer true now. Routing a child address may depend on the previous
+      routing that produced that child. Some complicated redirection strategies
+      went wrong when messages had multiple recipients, and made Exim's
+      behaviour dependent on the order in which the addresses were given.
+
+      I have moved the duplicate checking until after the routing is complete.
+      Exim scans the addresses that are assigned to local and remote
+      transports, and removes any duplicates. This means that more work will be
+      done, as duplicates will always all be routed, but duplicates are
+      presumably rare, so I don't expect this is of any significance.
+
+      For deliveries to pipes, files, and autoreplies, the duplicate checking
+      still happens during the routing process, since they are not going to be
+      routed further.
+
+PH/38 Installed a patch from Ian Freislich, with the agreement of Tom Kistner.
+      It corrects a timeout issue with spamd. This is Ian's comment: "The
+      background is that sometimes spamd either never reads data from a
+      connection it has accepted, or it never writes response data. The exiscan
+      spam.[ch] uses a 3600 second timeout on spamd socket reads, further, it
+      blindly assumes that writes won't block so it may never time out."
+
+PH/39 Allow G after quota size as well as K and M.
+
+PH/40 The value set for $authenticated_id in an authenticator may not contain
+      binary zeroes or newlines because the value is written to log lines and
+      to spool files. There was no check on this. Now the value is run through
+      the string_printing() function so that such characters are converted to
+      printable escape sequences.
+
+PH/41 $message_linecount is a new variable that contains the total number of
+      lines in the message. Compare $body_linecount, which is the count for the
+      body only.
+
+PH/42 Exim no longer gives details of delivery errors for specific addresses in
+      bounce and delay warning messages, except in certain special cases, which
+      are as follows:
+
+      (a) An SMTP error message from a remote host;
+      (b) A message specified in a :fail: redirection;
+      (c) A message specified in a "fail" command in a system filter;
+      (d) A message specified in a FAIL return from the queryprogram router;
+      (e) A message specified by the cannot_route_message router option.
+
+      In these cases only, Exim does include the error details in bounce and
+      warning messages. There are also a few cases where bland messages such
+      as "unrouteable address" or "local delivery error" are given.
+
+PH/43 $value is now also set for the "else" part of a ${run expansion.
+
 
 A note about Exim versions 4.44 and 4.50
 ----------------------------------------