X-Git-Url: https://git.exim.org/users/heiko/exim.git/blobdiff_plain/8c690dfdc2c09b4aebe32a077c67b41b8ee2a6f0..833c70bc6dc0b85ea942bb127515d582a91a6ed7:/doc/doc-docbook/spec.xfpt

diff --git a/doc/doc-docbook/spec.xfpt b/doc/doc-docbook/spec.xfpt
index 06373ccde..aab8c00d5 100644
--- a/doc/doc-docbook/spec.xfpt
+++ b/doc/doc-docbook/spec.xfpt
@@ -4274,7 +4274,7 @@ or &%-bs%& is used. For &%-bh%&, the protocol is forced to one of the standard
 SMTP protocol names (see the description of &$received_protocol$& in section
 &<<SECTexpvar>>&). For &%-bs%&, the protocol is always &"local-"& followed by
 one of those same names. For &%-bS%& (batched SMTP) however, the protocol can
-be set by &%-oMr%&.
+be set by &%-oMr%&. Repeated use of this option is not supported.
 
 .vitem &%-oMs%&&~<&'host&~name'&>
 .oindex "&%-oMs%&"
@@ -4374,6 +4374,7 @@ host name and its colon can be omitted when only the protocol is to be set.
 Note the Exim already has two private options, &%-pd%& and &%-ps%&, that refer
 to embedded Perl. It is therefore impossible to set a protocol value of &`d`&
 or &`s`& using this option (but that does not seem a real limitation).
+Repeated use of this option is not supported.
 
 .vitem &%-q%&
 .oindex "&%-q%&"
@@ -19468,6 +19469,10 @@ instead of TRY_AGAIN. That is why the default action is to try a DNS
 lookup first. Only if that gives a definite &"no such host"& is the local
 function called.
 
+&*Compatibility*&: From Exim 4.85 until fixed for 4.90, there was an
+inadvertent constraint that a transport name as an option had to be the last
+option specified.
+
 
 
 If no IP address for a host can be found, what happens is controlled by the
@@ -22127,10 +22132,14 @@ the obvious value which users understand most easily.
 
 The value of the option is expanded, and must then be a numerical value
 (decimal point allowed), optionally followed by one of the letters K, M, or G,
-for kilobytes, megabytes, or gigabytes. If Exim is running on a system with
+for kilobytes, megabytes, or gigabytes, optionally followed by a slash
+and further option modifiers. If Exim is running on a system with
 large file support (Linux and FreeBSD have this), mailboxes larger than 2G can
 be handled.
 
+The option modifier &%no_check%& can be used to force delivery even if the over
+quota condition is met. The quota gets updated as usual.
+
 &*Note*&: A value of zero is interpreted as &"no quota"&.
 
 The expansion happens while Exim is running as root, before it changes uid for
@@ -22165,6 +22174,8 @@ can only be used if &%quota%& is also set. The value is expanded; an expansion
 failure causes delivery to be deferred. A value of zero is interpreted as
 &"no quota"&.
 
+The option modifier &%no_check%& can be used to force delivery even if the over
+quota condition is met. The quota gets updated as usual.
 
 .option quota_is_inclusive appendfile boolean true
 See &%quota%& above.