X-Git-Url: https://git.exim.org/users/heiko/exim.git/blobdiff_plain/7ef88aa0c4c0608ee54ed2ff90b4b34c518d9bb5..d8024efa365d10d2dba4f06977776f4091250462:/doc/doc-txt/experimental-spec.txt

diff --git a/doc/doc-txt/experimental-spec.txt b/doc/doc-txt/experimental-spec.txt
index e9a557aec..3beab4b9c 100644
--- a/doc/doc-txt/experimental-spec.txt
+++ b/doc/doc-txt/experimental-spec.txt
@@ -642,6 +642,9 @@ ARC support
 Specification: https://tools.ietf.org/html/draft-ietf-dmarc-arc-protocol-11
 Note that this is not an RFC yet, so may change.
 
+[RFC 8617 was published 2019/06.  Draft 11 was 2018/01.  A review of the
+changes has not yet been done]
+
 ARC is intended to support the utility of SPF and DKIM in the presence of
 intermediaries in the transmission path - forwarders and mailinglists -
 by establishing a cryptographically-signed chain in headers.
@@ -650,10 +653,18 @@ Normally one would only bother doing ARC-signing when functioning as
 an intermediary.  One might do verify for local destinations.
 
 ARC uses the notion of a "ADministrative Management Domain" (ADMD).
-Described in RFC 5598 (section 2.3), this is essentially the set of
-mail-handling systems that the mail transits.  A label should be chosen to
-identify the ADMD.  Messages should be ARC-verified on entry to the ADMD,
-and ARC-signed on exit from it.
+Described in RFC 5598 (section 2.3), this is essentially a set of
+mail-handling systems that mail transits that are all under the control
+of one organisation.  A label should be chosen to identify the ADMD.
+Messages should be ARC-verified on entry to the ADMD, and ARC-signed on exit
+from it.
+
+
+Building with ARC Support
+--
+Enable using EXPERIMENTAL_ARC=yes in your Local/Makefile.
+You must also have DKIM present (not disabled), and you very likely
+want to have SPF enabled.
 
 
 Verification
@@ -797,6 +808,59 @@ Issues:
    hosts_require_ocsp will fail
 
 
+
+Dovecot authenticator via inet socket
+------------------------------------
+If Dovecot is configured similar to :-
+
+service auth {
+...
+#SASL
+  inet_listener {
+    name = exim
+    port = 12345
+  }
+...
+}
+
+then an Exim authenticator can be configured :-
+
+  dovecot-plain:
+    driver =		dovecot
+    public_name =	PLAIN
+    server_socket =	dovecot_server_name 12345
+    server_tls =	true
+    server_set_id =	$auth1
+
+If the server_socket does not start with a / it is taken as a hostname (or IP);
+and a whitespace-separated port number must be given.
+
+
+
+Twophase queue run fast ramp
+----------------------------
+To include this feature, add to Local/Makefile:
+  EXPERIMENTAL_QUEUE_RAMP=yes
+
+If the (added for this feature) main-section option "queue_fast_ramp" (boolean)
+is set, and a two-phase ("-qq") queue run finds, during the first phase, a
+suitably large number of message routed for a given host - then (subject to
+the usual queue-runner resource limits) delivery for that host is initiated
+immediately, overlapping with the remainder of the first phase.
+
+This is incompatible with queue_run_in_order.
+
+The result should be a faster startup of deliveries when a large queue is
+present and reasonable numbers of messages are routed to common hosts; this
+could be a smarthost case, or delivery onto the Internet where a large proportion
+of recipients hapen to be on a Gorilla-sized provider.
+
+As usual, the presence of a configuration option is associated with a
+predefined macro, making it possible to write portable configurations.
+For this one, the macro is _OPT_MAIN_QUEUE_FAST_RAMP.
+
+
+
 --------------------------------------------------------------
 End of file
 --------------------------------------------------------------