X-Git-Url: https://git.exim.org/users/heiko/exim.git/blobdiff_plain/7a5698faf84452ff9dcef170b3580921a4c3c9bf..ff57314ec0e6f83302fb2644ca16928322ff62a1:/doc/doc-docbook/spec.xfpt?ds=inline
diff --git a/doc/doc-docbook/spec.xfpt b/doc/doc-docbook/spec.xfpt
index bf50a9be8..31767bf55 100644
--- a/doc/doc-docbook/spec.xfpt
+++ b/doc/doc-docbook/spec.xfpt
@@ -179,12 +179,7 @@
EximMaintainers
EM
-
-.version
-
-
-.fulldate
-
+.versiondatexml
EM
@@ -8268,10 +8263,13 @@ apply to temporary DNS errors, whose handling is described in the next section.
.cindex "&`+include_unknown`&"
.cindex "&`+ignore_unknown`&"
-By default, Exim behaves as if the host does not match the list. This may not
-always be what you want to happen. To change Exim's behaviour, the special
-items &`+include_unknown`& or &`+ignore_unknown`& may appear in the list (at
-top level &-- they are not recognized in an indirected file).
+Exim parses a host list from left to right. If it encounters a permanent
+lookup failure in any item in the host list before it has found a match,
+Exim treats it as a failure and the default behavior is as if the host
+does not match the list. This may not always be what you want to happen.
+To change Exim's behaviour, the special items &`+include_unknown`& or
+&`+ignore_unknown`& may appear in the list (at top level &-- they are
+not recognized in an indirected file).
.ilist
If any item that follows &`+include_unknown`& requires information that
@@ -8299,6 +8297,37 @@ Both &`+include_unknown`& and &`+ignore_unknown`& may appear in the same
list. The effect of each one lasts until the next, or until the end of the
list.
+To explain the host/ip processing logic a different way for the same ACL:
+
+.ilist
+If you have name lookups or wildcarded host names and
+IP addresses in the same host list, you should normally put the IP
+addresses first. For example, in an ACL you could have:
+.code
+accept hosts = 10.9.8.7 : *.friend.example
+.endd
+The reason you normally would order it this way lies in the
+left-to-right way that Exim processes lists. It can test IP addresses
+without doing any DNS lookups, but when it reaches an item that requires
+a host name, it fails if it cannot find a host name to compare with the
+pattern. If the above list is given in the opposite order, the
+&%accept%& statement fails for a host whose name cannot be found, even
+if its IP address is 10.9.8.7.
+
+.next
+If you really do want to do the name check first, and still recognize the IP
+address, you can rewrite the ACL like this:
+.code
+accept hosts = *.friend.example
+accept hosts = 10.9.8.7
+.endd
+If the first &%accept%& fails, Exim goes on to try the second one. See chapter
+&<>& for details of ACLs. Alternatively, you can use
+&`+ignore_unknown`&, which was discussed in depth in the first example in
+this section.
+.endlist
+
+
.section "Temporary DNS errors when looking up host information" &&&
"SECTtemdnserr"
@@ -10337,6 +10366,8 @@ ${if forany{<, $recipients}{match{$item}{^user3@}}{yes}{no}}
The value of &$item$& is saved and restored while &*forany*& or &*forall*& is
being processed, to enable these expansion items to be nested.
+To scan a named list, expand it with the &*listnamed*& operator.
+
.vitem &*ge&~{*&<&'string1'&>&*}{*&<&'string2'&>&*}*& &&&
&*gei&~{*&<&'string1'&>&*}{*&<&'string2'&>&*}*&
@@ -10880,6 +10911,16 @@ the value of &$authenticated_id$& is normally the login name of the calling
process. However, a trusted user can override this by means of the &%-oMai%&
command line option.
+.vitem &$authenticated_fail_id$&
+.cindex "authentication" "fail" "id"
+.vindex "&$authenticated_fail_id$&"
+When an authentication attempt fails, the variable &$authenticated_fail_id$&
+will contain the failed authentication id. If more than one authentication
+id is attempted, it will contain only the last one. The variable is
+available for processing in the ACL's, generally the quit or notquit ACL.
+A message to a local recipient could still be accepted without requiring
+authentication, which means this variable could also be visible in all of
+the ACL's as well.
@@ -13984,7 +14025,7 @@ This option will let GnuTLS (2.12.0 or later) autoload PKCS11 modules with
the p11-kit configuration files in &_/etc/pkcs11/modules/_&.
See
-&url(http://www.gnu.org/software/gnutls/manual/gnutls.html#Smart-cards-and-HSMs)
+&url(http://www.gnutls.org/manual/gnutls.html#Smart-cards-and-HSMs)
for documentation.
.wen
@@ -14740,6 +14781,8 @@ Possible options may include:
.next
&`no_tlsv1_2`&
.next
+&`safari_ecdhe_ecdsa_bug`&
+.next
&`single_dh_use`&
.next
&`single_ecdh_use`&
@@ -14755,6 +14798,15 @@ Possible options may include:
&`tls_rollback_bug`&
.endlist
+.new
+As an aside, the &`safari_ecdhe_ecdsa_bug`& item is a misnomer and affects
+all clients connecting using the MacOS SecureTransport TLS facility prior
+to MacOS 10.8.4, including email clients. If you see old MacOS clients failing
+to negotiate TLS then this option value might help, provided that your OpenSSL
+release is new enough to contain this work-around. This may be a situation
+where you have to upgrade OpenSSL to get buggy clients working.
+.wen
+
.option oracle_servers main "string list" unset
.cindex "Oracle" "server list"
@@ -15324,6 +15376,13 @@ live with.
. Allow this long option name to split; give it unsplit as a fifth argument
. for the automatic .oindex that is generated by .option.
+. We insert " &~&~" which is both pretty nasty visually and results in
+. non-searchable text. HowItWorks.txt mentions an option for inserting
+. zero-width-space, which would be nicer visually and results in (at least)
+. html that Firefox will split on when it's forced to reflow (rather than
+. inserting a horizontal scrollbar). However, the text is still not
+. searchable. NM changed this occurrence for bug 1197 to no longer allow
+. the option name to split.
.option "smtp_accept_max_per_connection" main integer 1000 &&&
smtp_accept_max_per_connection
@@ -15375,10 +15434,9 @@ also &%queue_only%&, &%queue_only_load%&, &%queue_smtp_domains%&, and the
various &%-od%&&'x'& command line options.
-. Allow this long option name to split; give it unsplit as a fifth argument
-. for the automatic .oindex that is generated by .option.
+. See the comment on smtp_accept_max_per_connection
-.option "smtp_accept_queue_per_ &~&~connection" main integer 10 &&&
+.option "smtp_accept_queue_per_connection" main integer 10 &&&
smtp_accept_queue_per_connection
.cindex "queueing incoming messages"
.cindex "message" "queueing by message count"
@@ -16018,6 +16076,21 @@ The available primes are:
Some of these will be too small to be accepted by clients.
Some may be too large to be accepted by clients.
+The TLS protocol does not negotiate an acceptable size for this; clients tend
+to hard-drop connections if what is offered by the server is unacceptable,
+whether too large or too small, and there's no provision for the client to
+tell the server what these constraints are. Thus, as a server operator, you
+need to make an educated guess as to what is most likely to work for your
+userbase.
+
+Some known size constraints suggest that a bit-size in the range 2048 to 2236
+is most likely to maximise interoperability. The upper bound comes from
+applications using the Mozilla Network Security Services (NSS) library, which
+used to set its &`DH_MAX_P_BITS`& upper-bound to 2236. This affects many
+mail user agents (MUAs). The lower bound comes from Debian installs of Exim4
+prior to the 4.80 release, as Debian used to patch Exim to raise the minimum
+acceptable bound from 1024 to 2048.
+
.option tls_on_connect_ports main "string list" unset
This option specifies a list of incoming SSMTP (aka SMTPS) ports that should
@@ -23537,7 +23610,7 @@ In practice, almost all rules start with a domain name pattern without a local
part.
.cindex "regular expressions" "in retry rules"
-&*Warning*&: If you use a regular expression in a routing rule pattern, it
+&*Warning*&: If you use a regular expression in a retry rule pattern, it
must match a complete address, not just a domain, because that is how regular
expressions work in address lists.
.display
@@ -24520,7 +24593,8 @@ to be returned. If the result of a successful expansion is an empty string,
expansion is &"1"&, &"yes"&, or &"true"&, authentication succeeds and the
generic &%server_set_id%& option is expanded and saved in &$authenticated_id$&.
For any other result, a temporary error code is returned, with the expanded
-string as the error text.
+string as the error text, and the failed id saved in
+&$authenticated_fail_id$&.
&*Warning*&: If you use a lookup in the expansion to find the user's
password, be sure to make the authentication fail if the user is unknown.
@@ -25584,10 +25658,10 @@ aware of future feature enhancements of GnuTLS.
Documentation of the strings accepted may be found in the GnuTLS manual, under
"Priority strings". This is online as
-&url(http://www.gnu.org/software/gnutls/manual/html_node/Priority-Strings.html),
+&url(http://www.gnutls.org/manual/html_node/Priority-Strings.html),
but beware that this relates to GnuTLS 3, which may be newer than the version
installed on your system. If you are using GnuTLS 3,
-&url(http://www.gnu.org/software/gnutls/manual/html_node/Listing-the-ciphersuites-in-a-priority-string.html, then the example code)
+&url(http://www.gnutls.org/manual/gnutls.html#Listing-the-ciphersuites-in-a-priority-string, then the example code)
on that site can be used to test a given string.
Prior to Exim 4.80, an older API of GnuTLS was used, and Exim supported three
@@ -25673,7 +25747,7 @@ tls_dhparam = none
This may also be set to a string identifying a standard prime to be used for
DH; if it is set to &`default`& or, for OpenSSL, is unset, then the prime
used is &`ike23`&. There are a few standard primes available, see the
-documetnation for &%tls_dhparam%& for the complete list.
+documentation for &%tls_dhparam%& for the complete list.
See the command
.code
@@ -34422,14 +34496,14 @@ options are available:
.vlist
.vitem &*-f*&&~<&'regex'&>
-Match the sender address. The field that is tested is enclosed in angle
-brackets, so you can test for bounce messages with
+Match the sender address using a case-insensitive search. The field that is
+tested is enclosed in angle brackets, so you can test for bounce messages with
.code
exiqgrep -f '^<>$'
.endd
.vitem &*-r*&&~<&'regex'&>
-Match a recipient address. The field that is tested is not enclosed in angle
-brackets.
+Match a recipient address using a case-insensitve search. The field that is
+tested is not enclosed in angle brackets.
.vitem &*-s*&&~<&'regex'&>
Match against the size field.
@@ -36374,7 +36448,7 @@ integer size comparisons against this value.
A colon-separated list of names of headers included in the signature.
.vitem &%$dkim_key_testing%&
"1" if the key record has the "testing" flag set, "0" if not.
-.vitem &%$nosubdomains%&
+.vitem &%$dkim_key_nosubdomains%&
"1" if the key record forbids subdomaining, "0" otherwise.
.vitem &%$dkim_key_srvtype%&
Service type (tag s=) from the key record. Defaults to "*" if not specified