X-Git-Url: https://git.exim.org/users/heiko/exim.git/blobdiff_plain/2db98699739386432d423a1effc17994c88e0018..0793e4edcdcdb346f10794a1b3f344968e39b79d:/doc/doc-misc/WishList?ds=sidebyside diff --git a/doc/doc-misc/WishList b/doc/doc-misc/WishList index 93030f270..80c8c6370 100644 --- a/doc/doc-misc/WishList +++ b/doc/doc-misc/WishList @@ -1,4 +1,4 @@ -$Cambridge: exim/doc/doc-misc/WishList,v 1.37 2005/06/07 15:36:47 ph10 Exp $ +$Cambridge: exim/doc/doc-misc/WishList,v 1.42 2005/06/29 14:19:28 ph10 Exp $ EXIM 4 WISH LIST ---------------- @@ -864,24 +864,6 @@ So as to avoid duplication problems when sending multiple addresses in multiple copies to the same address. ------------------------------------------------------------------------------ -(73) 17-Jul-02 M Match a list from within a condition - -e.g. ${if matchdomain {$domain}{+domainlist} ... - ${if matchhost {$sender_host_address}{1.2.3.4/10:2.3.4.5/16}... - -Thought needed about how to handle host names. This may be too messy to specify -cleanly. - -22-Apr-04: Implemented for domains, addresses, and local parts. Hosts are -too messy! - -The only sensible approach seems to be to allow IP address arguments only. -Anything else should be diagnosed as an error. However, if a name appears in -the list, a PTR lookup should be done. This may require a lot of refactoring -in the code, because of the current assumption that were are (almost) always -dealing with THE sending host. ------------------------------------------------------------------------------- - (74) 22-Jul-02 M Extend -bV to do more semantic checking For example, diagnose "local_hosts" that should probably be "+local_hosts". @@ -1881,12 +1863,6 @@ file would contain the complete email. I suppose there may be other scanning solutions with a similar requirement." ------------------------------------------------------------------------------ -(320) 03-Mar-05 T Options to control daemon retry binding - -Currently the daemon tries 10 times at 30-second intervals to listen on an IP -address. The wish is for options to control these numbers. ------------------------------------------------------------------------------- - (321) 07-Mar-05 S Run an ACL on a sync error ... and possibly "accept" or "deny" it. @@ -1985,5 +1961,29 @@ Exim 4 Wish List: 55, 62, 63, 160, 212, 237, 270, 314, 328. This is probably a longish-term thing at the moment. Quotas over 2G are now supported, but not individual messages; no doubt one day this will be wanted. ------------------------------------------------------------------------------ ---- HWM 334 ------------------------------------------------------------------ + +(335) 14-Jun-05 T Re-arrange default configuration + +A small niggle which might be worth fixing is the ordering of the ACL in the +default configuration file. The relay_from_hosts and authenticated clauses +would be better off before the dnslists examples. However, this should be left +until a x.x0 release, because of the documentation implications. +------------------------------------------------------------------------------ + +(336) 16-Jun-05 M Show recipient(s) after header check failure + +The mainlog line for "There is no valid sender in any header line" shows the +sending host and the envelope sender, but does not show any recipients. There +has been a request to show recipients. Presumably this should be on some new +log selector, and it must have a cutoff maximum number of recipients. NOTE: the +data in the reject log does show the envelope recipients as part of its +additional data. +------------------------------------------------------------------------------ + +(337) 29-Jun-06 S Add "defer" to $recipient_verify_failure + +This is for when defer_ok was set when verifying recipients. Since this isn't +for a failure, we probably also need "ok" for the non-fail case. +------------------------------------------------------------------------------ +--- HWM 337 ------------------------------------------------------------------ ---------------------------- End of WishList ---------------------------------