X-Git-Url: https://git.exim.org/users/heiko/exim.git/blobdiff_plain/01a4a5c5cbaa40ca618d3e233991ce183b551477..7eb6c37c5084760c1d1469bd4be652b479a8df55:/doc/doc-txt/experimental-spec.txt diff --git a/doc/doc-txt/experimental-spec.txt b/doc/doc-txt/experimental-spec.txt index 4bcfecf04..e6e066c04 100644 --- a/doc/doc-txt/experimental-spec.txt +++ b/doc/doc-txt/experimental-spec.txt @@ -623,10 +623,10 @@ exim will send these forensic emails. It's also advised that you configure a dmarc_forensic_sender because the default sender address construction might be inadequate. - control = dmarc_forensic_enable + control = dmarc_enable_forensic (AGAIN: You can choose not to send these forensic reports by simply -not putting the dmarc_forensic_enable control line at any point in +not putting the dmarc_enable_forensic control line at any point in your exim config. If you don't tell it to send them, it will not send them.) @@ -755,7 +755,7 @@ b. Configure, somewhere before the DATA ACL, the control option to deny dmarc_status = reject !authenticated = * - message = Message from $domain_used_domain failed sender's DMARC policy, REJECT + message = Message from $dmarc_used_domain failed sender's DMARC policy, REJECT @@ -1084,64 +1084,37 @@ QUIT 221 mail.example.net closing connection -DSN Support --------------------------------------------------------------- - -DSN Support tries to add RFC 3461 support to Exim. It adds support for -*) the additional parameters for MAIL FROM and RCPT TO -*) RFC complient MIME DSN messages for all of - success, failure and delay notifications -*) dsn_advertise_hosts main option to select which hosts are able - to use the extension -*) dsn_lasthop router switch to end DSN processing - -In case of failure reports this means that the last three parts, the message body -intro, size info and final text, of the defined template are ignored since there is no -logical place to put them in the MIME message. - -All the other changes are made without changing any defaults - -Building exim: --------------- - -Define -EXPERIMENTAL_DSN=YES -in your Local/Makefile. - -Configuration: --------------- -All DSNs are sent in MIME format if you built exim with EXPERIMENTAL_DSN=YES -No option needed to activate it, and no way to turn it off. -Failure and delay DSNs are triggered as usual except a sender used NOTIFY=... -to prevent them. -Support for Success DSNs is added and activated by NOTIFY=SUCCESS by clients. - -Add -dsn_advertise_hosts = * -or a more restrictive host_list to announce DSN in EHLO answers - -Those hosts can then use NOTIFY,ENVID,RET,ORCPT options. - -If a message is relayed to a DSN aware host without changing the envelope -recipient the options are passed along and no success DSN is generated. - -A redirect router will always trigger a success DSN if requested and the DSN -options are not passed any further. - -A success DSN always contains the recipient address as submitted by the -client as required by RFC. Rewritten addresses are never exposed. - -If you used DSN patch up to 1.3 before remove all "dsn_process" switches from -your routers since you don't need them anymore. There is no way to "gag" -success DSNs anymore. Announcing DSN means answering as requested. - -You can prevent Exim from passing DSN options along to other DSN aware hosts by defining -dsn_lasthop -in a router. Exim will then send the success DSN himself if requested as if -the next hop does not support DSN. -Adding it to a redirect router makes no difference. +SOCKS +------------------------------------------------------------ +Support for proxying outbound SMTP via a Socks 5 proxy +(RFC 1928) is included if Exim is compiled with +EXPERIMENTAL_SOCKS defined. + +If an smtp transport has a nonempty socks_proxy option +defined, this is active. The option is expanded and +should be a list (colon-separated by default) of +proxy specifiers. Each proxy specifier is a list +(space-separated by default) where the initial element +is an IP address and any subsequent elements are options. + +Options are a string =. +These options are currently defined: +- "auth", with possible values "none" and "name". + Using "name" selects username/password authentication + per RFC 1929. Default is "none". +- "name" sets the authentication username. Default is empty. +- "pass" sets the authentication password. Default is empty. +- "port" sets the tcp port number for the proxy. Default is 1080. +- "tmo" sets a connection timeout in seconds for this proxy. Default is 5. + +Proxies from the list are tried in order until +one responds. The timeout for the overall connection +applies to the set of proxied attempts. + +If events are used, the remote IP/port during a +tcp:connect event will be that of the proxy.