-$Cambridge: exim/doc/doc-txt/NewStuff,v 1.41 2005/05/17 09:53:34 ph10 Exp $
+$Cambridge: exim/doc/doc-txt/NewStuff,v 1.131 2007/01/30 11:45:20 ph10 Exp $
New Features in Exim
--------------------
-This file contains descriptions of new features that have been added to Exim,
-but have not yet made it into the main manual (which is most conveniently
-updated when there is a relatively large batch of changes). The doc/ChangeLog
-file contains a listing of all changes, including bug fixes.
-
-
-Exim version 4.52
------------------
-
-TF/01 Support for checking Client SMTP Authorization has been added. CSA is a
- system which allows a site to advertise which machines are and are not
- permitted to send email. This is done by placing special SRV records in
- the DNS, which are looked up using the client's HELO domain. At this
- time CSA is still an Internet-Draft.
-
- Client SMTP Authorization checks are performed by the ACL condition
- verify=csa. This will fail if the client is not authorized. If there is
- a DNS problem, or if no valid CSA SRV record is found, or if the client
- is authorized, the condition succeeds. These three cases can be
- distinguished using the expansion variable $csa_status, which can take
- one of the values "fail", "defer", "unknown", or "ok". The condition
- does not itself defer because that would be likely to cause problems
- for legitimate email.
-
- The error messages produced by the CSA code include slightly more
- detail. If $csa_status is "defer" this may be because of problems
- looking up the CSA SRV record, or problems looking up the CSA target
- address record. There are four reasons for $csa_status being "fail":
- the client's host name is explicitly not authorized; the client's IP
- address does not match any of the CSA target IP addresses; the client's
- host name is authorized but it has no valid target IP addresses (e.g.
- the target's addresses are IPv6 and the client is using IPv4); or the
- client's host name has no CSA SRV record but a parent domain has
- asserted that all subdomains must be explicitly authorized.
-
- The verify=csa condition can take an argument which is the domain to
- use for the DNS query. The default is verify=csa/$sender_helo_name.
-
- This implementation includes an extension to CSA. If the query domain
- is an address literal such as [192.0.2.95], or if it is a bare IP
- address, Exim will search for CSA SRV records in the reverse DNS as if
- the HELO domain was e.g. 95.2.0.192.in-addr.arpa. Therefore it is
- meaningful to say, for example, verify=csa/$sender_host_address - in
- fact, this is the check that Exim performs if the client does not say
- HELO. This extension can be turned off by setting the main
- configuration option dns_csa_use_reverse = false.
-
- If a CSA SRV record is not found for the domain itself, then a search
- is performed through its parent domains for a record which might be
- making assertions about subdomains. The maximum depth of this search is
- limited using the main configuration option dns_csa_search_limit, which
- takes the value 5 by default. Exim does not look for CSA SRV records in
- a top level domain, so the default settings handle HELO domains as long
- as seven (hostname.five.four.three.two.one.com) which encompasses the
- vast majority of legitimate HELO domains.
-
- The dnsdb lookup also has support for CSA. Although dnsdb already
- supports SRV lookups, this is not sufficient because of the extra
- parent domain search behaviour of CSA, and (as with PTR lookups)
- dnsdb also turns IP addresses into lookups in the reverse DNS space.
- The result of ${lookup dnsdb {csa=$sender_helo_name} } has two
- space-separated fields: an authorization code and a target host name.
- The authorization code can be "Y" for yes, "N" for no, "X" for explicit
- authorization required but absent, or "?" for unknown.
-
-PH/01 The amount of output produced by the "make" process has been reduced,
- because the compile lines are often rather long, making it all pretty
- unreadable. The new style is along the lines of the 2.6 Linux kernel:
- just a short line for each module that is being compiled or linked.
- However, it is still possible to get the full output, by calling "make"
- like this:
-
- FULLECHO='' make -e
-
- The value of FULLECHO defaults to "@", the flag character that suppresses
- command reflection in "make". When you ask for the full output, it is
- given in addition to the the short output.
-
-
-Version 4.51
+This file contains descriptions of new features that have been added to Exim.
+Before a formal release, there may be quite a lot of detail so that people can
+test from the snapshots or the CVS before the documentation is updated. Once
+the documentation is updated, this file is reduced to a short list.
+
+Version 4.67
------------
-PH/01 The format in which GnuTLS parameters are written to the gnutls-param
- file in the spool directory has been changed. This change has been made
- to alleviate problems that some people had with the generation of the
- parameters by Exim when /dev/random was exhausted. In this situation,
- Exim would hang until /dev/random acquired some more entropy.
+ 1. There is a new log selector called smtp_no_mail, which is not included in
+ the default setting. When it is set, a line is written to the main log
+ whenever an accepted SMTP connection terminates without having issued a
+ MAIL command. This includes both the case when the connection is dropped,
+ and the case when QUIT is used. Note that it does not include cases where
+ the connection is rejected right at the start (by an ACL, or because there
+ are too many connections, or whatever). These cases already have their own
+ log lines.
+
+ The log line that is written contains the identity of the client in the
+ usual way, followed by D= and a time, which records the duration of the
+ connection. If the connection was authenticated, this fact is logged
+ exactly as it is for an incoming message, with an A= item. If the
+ connection was encrypted, CV=, DN=, and X= items may appear as they do for
+ an incoming message, controlled by the same logging options.
+
+ Finally, if any SMTP commands were issued during the connection, a C= item
+ is added to the line, listing the commands that were used. For example,
+
+ C=EHLO,QUIT
+
+ shows that the client issued QUIT straight after EHLO. If there were fewer
+ than 20 commands, they are all listed. If there were more than 20 commands,
+ the last 20 are listed, preceded by "...". However, with the default
+ setting of 10 for smtp_accep_max_nonmail, the connection will in any case
+ be aborted before 20 non-mail commands are processed.
+
+ 2. When an item in a dnslists list is followed by = and & and a list of IP
+ addresses, in order to restrict the match to specific results from the DNS
+ lookup, the behaviour was not clear when the lookup returned more than one
+ IP address. For example, consider the condition
+
+ dnslists = a.b.c=127.0.0.1
+
+ What happens if the DNS lookup for the incoming IP address yields both
+ 127.0.0.1 and 127.0.0.2 by means of two separate DNS records? Is the
+ condition true because at least one given value was found, or is it false
+ because at least one of the found values was not listed? And how does this
+ affect negated conditions?
+
+ The behaviour of = and & has not been changed; however, the text below
+ documents it more clearly. In addition, two new additional conditions (==
+ and =&) have been added, to permit the "other" behaviour to be configured.
+
+ A DNS lookup may yield more than one record. Thus, the result of the lookup
+ for a dnslists check may yield more than one IP address. The question then
+ arises as to whether all the looked up addresses must be listed, or whether
+ just one is good enough. Both possibilities are provided for:
+
+ . If = or & is used, the condition is true if any one of the looked up
+ IP addresses matches one of the listed addresses. Consider:
+
+ dnslists = a.b.c=127.0.0.1
+
+ If the DNS lookup yields both 127.0.0.1 and 127.0.0.2, the condition is
+ true because 127.0.0.1 matches.
+
+ . If == or =& is used, the condition is true only if every one of the
+ looked up IP addresses matches one of the listed addresses. Consider:
+
+ dnslists = a.b.c==127.0.0.1
+
+ If the DNS lookup yields both 127.0.0.1 and 127.0.0.2, the condition is
+ false because 127.0.0.2 is not listed. You would need to have
+
+ dnslists = a.b.c==127.0.0.1,127.0.0.2
+
+ for the condition to be true.
+
+ When ! is used to negate IP address matching, it inverts the result, giving
+ the precise opposite of the behaviour above. Thus:
+
+ . If != or !& is used, the condition is true if none of the looked up IP
+ addresses matches one of the listed addresses. Consider:
+
+ dnslists = a.b.c!&0.0.0.1
+
+ If the DNS lookup yields both 127.0.0.1 and 127.0.0.2, the condition is
+ false because 127.0.0.1 matches.
- The new code exports and imports the DH and RSA parameters in PEM
- format. This means that the parameters can be generated externally using
- the certtool command that is part of GnuTLS.
+ . If !== or !=& is used, the condition is true there is at least one looked
+ up IP address that does not match. Consider:
- To replace the parameters with new ones, instead of deleting the file
- and letting Exim re-create it, you can generate new parameters using
- certtool and, when this has been done, replace Exim's cache file by
- renaming. The relevant commands are something like this:
+ dnslists = a.b.c!=&0.0.0.1
- # rm -f new.params
- # touch new.params
- # chown exim:exim new.params
- # chmod 0400 new.params
- # certtool --generate-privkey --bits 512 >new.params
- # echo "" >>new.params
- # certtool --generate-dh-params --bits 1024 >> new.params
- # mv new.params params
+ If the DNS lookup yields both 127.0.0.1 and 127.0.0.2, the condition is
+ true, because 127.0.0.2 does not match. You would need to have
- If Exim never has to generate the parameters itself, the possibility of
- stalling is removed.
+ dnslists = a.b.c!=&0.0.0.1,0.0.0.2
-PH/02 A new expansion item for dynamically loading and calling a locally-
- written C function is now provided, if Exim is compiled with
+ for the condition to be false.
- EXPAND_DLFUNC=yes
+ When the DNS lookup yields only a single IP address, there is no difference
+ between = and == and between & and =&.
- set in Local/Makefile. The facility is not included by default (a
- suitable error is given if you try to use it when it is not there.)
+ 3. Up till now, the only control over which cipher suites GnuTLS uses has been
+ for the cipher algorithms. New options have been added to allow some of the
+ other parameters to be varied. Here is complete documentation for the
+ available features:
- If you enable EXPAND_DLFUNC, you should also be aware of the new redirect
- router option forbid_filter_dlfunc. If you have unprivileged users on
- your system who are permitted to create filter files, you might want to
- set forbid_filter_dlfunc=true in the appropriate router, to stop them
- using ${dlfunc to run code within Exim.
+ GnuTLS allows the caller to specify separate lists of permitted key
+ exchange methods, main cipher algorithms, and MAC algorithms. These may be
+ used in any combination to form a specific cipher suite. This is unlike
+ OpenSSL, where complete cipher names can be passed to its control function.
+ GnuTLS also allows a list of acceptable protocols to be supplied.
- You load and call an external function like this:
-
- ${dlfunc{/some/file}{function}{arg1}{arg2}...}
-
- Once loaded, Exim remembers the dynamically loaded object so that it
- doesn't reload the same object file in the same Exim process (but of
- course Exim does start new processes frequently).
-
- There may be from zero to eight arguments to the function. When compiling
- a local function that is to be called in this way, local_scan.h should be
- included. The Exim variables and functions that are defined by that API
- are also available for dynamically loaded functions. The function itself
- must have the following type:
-
- int dlfunction(uschar **yield, int argc, uschar *argv[])
-
- Where "uschar" is a typedef for "unsigned char" in local_scan.h. The
- function should return one of the following values:
-
- OK Success. The string that is placed in "yield" is put into
- the expanded string that is being built.
-
- FAIL A non-forced expansion failure occurs, with the error
- message taken from "yield", if it is set.
-
- FAIL_FORCED A forced expansion failure occurs, with the error message
- taken from "yield" if it is set.
-
- ERROR Same as FAIL, except that a panic log entry is written.
-
- When compiling a function that is to be used in this way with gcc,
- you need to add -shared to the gcc command. Also, in the Exim build-time
- configuration, you must add -export-dynamic to EXTRALIBS.
-
-TF/01 $received_time is a new expansion variable containing the time and date
- as a number of seconds since the start of the Unix epoch when the
- current message was received.
-
-PH/03 There is a new value for RADIUS_LIB_TYPE that can be set in
- Local/Makefile. It is RADIUSCLIENTNEW, and it requests that the new API,
- in use from radiusclient 0.4.0 onwards, be used. It does not appear to be
- possible to detect the different versions automatically.
-
-PH/04 There is a new option called acl_not_smtp_mime that allows you to scan
- MIME parts in non-SMTP messages. It operates in exactly the same way as
- acl_smtp_mime
-
-PH/05 It is now possible to redefine a macro within the configuration file.
- The macro must have been previously defined within the configuration (or
- an included file). A definition on the command line using the -D option
- causes all definitions and redefinitions within the file to be ignored.
- In other words, -D overrides any values that are set in the file.
- Redefinition is specified by using '==' instead of '='. For example:
-
- MAC1 = initial value
- ...
- MAC1 == updated value
-
- Redefinition does not alter the order in which the macros are applied to
- the subsequent lines of the configuration file. It is still the same
- order in which the macros were originally defined. All that changes is
- the macro's value. Redefinition makes it possible to accumulate values.
- For example:
-
- MAC1 = initial value
- ...
- MAC1 == MAC1 and something added
-
- This can be helpful in situations where the configuration file is built
- from a number of other files.
-
-PH/06 Macros may now be defined or redefined between router, transport,
- authenticator, or ACL definitions, as well as in the main part of the
- configuration. They may not, however, be changed within an individual
- driver or ACL, or in the local_scan, retry, or rewrite sections of the
- configuration.
-
-PH/07 $acl_verify_message is now set immediately after the failure of a
- verification in an ACL, and so is available in subsequent modifiers. In
- particular, the message can be preserved by coding like this:
+ For compatibility with OpenSSL, the tls_require_ciphers option can be set
+ to complete cipher suite names such as RSA_ARCFOUR_SHA, but for GnuTLS this
+ option controls only the cipher algorithms. Exim searches each item in the
+ list for the name of an available algorithm. For example, if the list
+ contains RSA_AES_SHA, then AES is recognized, and the behaviour is exactly
+ the same as if just AES were given.
- warn !verify = sender
- set acl_m0 = $acl_verify_message
+ There are additional options called gnutls_require_kx, gnutls_require_mac,
+ and gnutls_require_protocols that can be used to restrict the key exchange
+ methods, MAC algorithms, and protocols, respectively. These options are
+ ignored if OpenSSL is in use.
- Previously, $acl_verify_message was set only while expanding "message"
- and "log_message" when a very denied access.
-
-PH/08 The redirect router has two new options, sieve_useraddress and
- sieve_subaddress. These are passed to a Sieve filter to specify the :user
- and :subaddress parts of an address. Both options are unset by default.
- However, when a Sieve filter is run, if sieve_useraddress is unset, the
- entire original local part (including any prefix or suffix) is used for
- :user. An unset subaddress is treated as an empty subaddress.
-
-PH/09 Quota values can be followed by G as well as K and M.
-
-PH/10 $message_linecount is a new variable that contains the total number of
- lines in the header and body of the message. Compare $body_linecount,
- which is the count for the body only. During the DATA and
- content-scanning ACLs, $message_linecount contains the number of lines
- received. Before delivery happens (that is, before filters, routers, and
- transports run) the count is increased to include the Received: header
- line that Exim standardly adds, and also any other header lines that are
- added by ACLs. The blank line that separates the message header from the
- body is not counted. Here is an example of the use of this variable in a
- DATA ACL:
-
- deny message = Too many lines in message header
- condition = \
- ${if <{250}{${eval: $message_linecount - $body_linecount}}}
-
- In the MAIL and RCPT ACLs, the value is zero because at that stage the
- message has not yet been received.
-
-PH/11 In a ${run expansion, the variable $value (which contains the standard
- output) is now also usable in the "else" string.
-
-PH/12 In a pipe transport, although a timeout while waiting for the pipe
- process to complete was treated as a delivery failure, a timeout while
- writing the message to the pipe was logged, but erroneously treated as a
- successful delivery. Such timeouts include transport filter timeouts. For
- consistency with the overall process timeout, these timeouts are now
- treated as errors, giving rise to delivery failures by default. However,
- there is now a new Boolean option for the pipe transport called
- timeout_defer, which, if set TRUE, converts the failures into defers for
- both kinds of timeout. A transport filter timeout is now identified in
- the log output.
-
-
-Version 4.50
+ All four options are available as global options, controlling how Exim
+ behaves as a server, and also as options of the smtp transport, controlling
+ how Exim behaves as a client. All the values are string expanded. After
+ expansion, the values must be colon-separated lists, though the separator
+ can be changed in the usual way.
+
+ Each of the four lists starts out with a default set of algorithms. If the
+ first item in one of the "require" options does _not_ start with an
+ exclamation mark, all the default items are deleted. In this case, only
+ those that are explicitly specified can be used. If the first item in one
+ of the "require" items _does_ start with an exclamation mark, the defaults
+ are left on the list.
+
+ Then, any item that starts with an exclamation mark causes the relevant
+ entry to be removed from the list, and any item that does not start with an
+ exclamation mark causes a new entry to be added to the list. Unrecognized
+ items in the list are ignored. Thus:
+
+ tls_require_ciphers = !ARCFOUR
+
+ allows all the defaults except ARCFOUR, whereas
+
+ tls_require_ciphers = AES : 3DES
+
+ allows only cipher suites that use AES or 3DES. For tls_require_ciphers
+ the recognized names are AES_256, AES_128, AES (both of the preceding),
+ 3DES, ARCFOUR_128, ARCFOUR_40, and ARCFOUR (both of the preceding). The
+ default list does not contain all of these; it just has AES_256, AES_128,
+ 3DES, and ARCFOUR_128.
+
+ For gnutls_require_kx, the recognized names are DHE_RSA, RSA (which
+ includes DHE_RSA), DHE_DSS, and DHE (which includes both DHE_RSA and
+ DHE_DSS). The default list contains RSA, DHE_DSS, DHE_RSA.
+
+ For gnutls_require_mac, the recognized names are SHA (synonym SHA1), and
+ MD5. The default list contains SHA, MD5.
+
+ For gnutls_require_protocols, the recognized names are TLS1 and SSL3.
+ The default list contains TLS1, SSL3.
+
+ In a server, the order of items in these lists is unimportant. The server
+ will advertise the availability of all the relevant cipher suites. However,
+ in a client, the order in the tls_require_ciphers list specifies a
+ preference order for the cipher algorithms. The first one in the client's
+ list that is also advertised by the server is tried first.
+
+ 4. There is a new compile-time option called ENABLE_DISABLE_FSYNC. You must
+ not set this option unless you really, really, really understand what you
+ are doing. No pre-compiled distributions of Exim should ever set this
+ option. When it is set, Exim compiles a runtime option called
+ disable_fsync. If this is set true, Exim no longer calls fsync() to force
+ updated files' data to be written to disc. Unexpected events such as
+ crashes and power outages may cause data to be lost or scrambled. Beware.
+
+ When ENABLE_DISABLE_FSYNC is not set, a reference to disable_fsync in a
+ runtime configuration generates an "unknown option" error.
+
+ 5. There is a new variable called $smtp_count_at_connection_start. The name
+ is deliberately long, in order to emphasize what the contents are. This
+ variable is set greater than zero only in processes spawned by the Exim
+ daemon for handling incoming SMTP connections. When the daemon accepts a
+ new connection, it increments this variable. A copy of the variable is
+ passed to the child process that handles the connection, but its value is
+ fixed, and never changes. It is only an approximation of how many incoming
+ connections there actually are, because many other connections may come and
+ go while a single connection is being processed. When a child process
+ terminates, the daemon decrements the variable.
+
+ 6. There's a new control called no_pipelining, which does what its name
+ suggests. It turns off the advertising of the PIPELINING extension to SMTP.
+ To be useful, this control must be obeyed before Exim sends its response to
+ an EHLO command. Therefore, it should normally appear in an ACL controlled
+ by acl_smtp_connect or acl_smtp_helo.
+
+
+Version 4.66
+------------
+
+No new features were added to 4.66.
+
+
+Version 4.65
------------
-The documentation is up-to-date for the 4.50 release.
+No new features were added to 4.65.
+
+
+Version 4.64
+------------
+
+ 1. ACL variables can now be given arbitrary names, as long as they start with
+ "acl_c" or "acl_m" (for connection variables and message variables), are at
+ least six characters long, with the sixth character being either a digit or
+ an underscore.
+
+ 2. There is a new ACL modifier called log_reject_target. It makes it possible
+ to specify which logs are used for messages about ACL rejections.
+
+ 3. There is a new authenticator called "dovecot". This is an interface to the
+ authentication facility of the Dovecot POP/IMAP server, which can support a
+ number of authentication methods.
+
+ 4. The variable $message_headers_raw provides a concatenation of all the
+ messages's headers without any decoding. This is in contrast to
+ $message_headers, which does RFC2047 decoding on the header contents.
+
+ 5. In a DNS black list, if two domain names, comma-separated, are given, the
+ second is used first to do an initial check, making use of any IP value
+ restrictions that are set. If there is a match, the first domain is used,
+ without any IP value restrictions, to get the TXT record.
+
+ 6. All authenticators now have a server_condition option.
+
+ 7. There is a new command-line option called -Mset. It is useful only in
+ conjunction with -be (that is, when testing string expansions). It must be
+ followed by a message id; Exim loads the given message from its spool
+ before doing the expansions.
+
+ 8. Another similar new command-line option is called -bem. It operates like
+ -be except that it must be followed by the name of a file that contains a
+ message.
+
+ 9. When an address is delayed because of a 4xx response to a RCPT command, it
+ is now the combination of sender and recipient that is delayed in
+ subsequent queue runs until its retry time is reached.
+
+10. Unary negation and the bitwise logical operators and, or, xor, not, and
+ shift, have been added to the eval: and eval10: expansion items.
+
+11. The variables $interface_address and $interface_port have been renamed
+ as $received_ip_address and $received_port, to make it clear that they
+ relate to message reception rather than delivery. (The old names remain
+ available for compatibility.)
+
+12. The "message" modifier can now be used on "accept" and "discard" acl verbs
+ to vary the message that is sent when an SMTP command is accepted.
+
+
+Version 4.63
+------------
+
+1. There is a new Boolean option called filter_prepend_home for the redirect
+ router.
+
+2. There is a new acl, set by acl_not_smtp_start, which is run right at the
+ start of receiving a non-SMTP message, before any of the message has been
+ read.
+
+3. When an SMTP error message is specified in a "message" modifier in an ACL,
+ or in a :fail: or :defer: message in a redirect router, Exim now checks the
+ start of the message for an SMTP error code.
+
+4. There is a new parameter for LDAP lookups called "referrals", which takes
+ one of the settings "follow" (the default) or "nofollow".
+
+5. Version 20070721.2 of exipick now included, offering these new options:
+ --reverse
+ After all other sorting options have bee processed, reverse order
+ before displaying messages (-R is synonym).
+ --random
+ Randomize order of matching messages before displaying.
+ --size
+ Instead of displaying the matching messages, display the sum
+ of their sizes.
+ --sort <variable>[,<variable>...]
+ Before displaying matching messages, sort the messages according to
+ each messages value for each variable.
+ --not
+ Negate the value for every test (returns inverse output from the
+ same criteria without --not).
+
+
+Version 4.62
+------------
+
+1. The ${readsocket expansion item now supports Internet domain sockets as well
+ as Unix domain sockets. If the first argument begins "inet:", it must be of
+ the form "inet:host:port". The port is mandatory; it may be a number or the
+ name of a TCP port in /etc/services. The host may be a name, or it may be an
+ IP address. An ip address may optionally be enclosed in square brackets.
+ This is best for IPv6 addresses. For example:
+
+ ${readsocket{inet:[::1]:1234}{<request data>}...
+
+ Only a single host name may be given, but if looking it up yield more than
+ one IP address, they are each tried in turn until a connection is made. Once
+ a connection has been made, the behaviour is as for ${readsocket with a Unix
+ domain socket.
+
+2. If a redirect router sets up file or pipe deliveries for more than one
+ incoming address, and the relevant transport has batch_max set greater than
+ one, a batch delivery now occurs.
+
+3. The appendfile transport has a new option called maildirfolder_create_regex.
+ Its value is a regular expression. For a maildir delivery, this is matched
+ against the maildir directory; if it matches, Exim ensures that a
+ maildirfolder file is created alongside the new, cur, and tmp directories.
+
+
+Version 4.61
+------------
+
+The documentation is up-to-date for the 4.61 release. Major new features since
+the 4.60 release are:
+
+. An option called disable_ipv6, to disable the use of IPv6 completely.
+
+. An increase in the number of ACL variables to 20 of each type.
+
+. A change to use $auth1, $auth2, and $auth3 in authenticators instead of $1,
+ $2, $3, (though those are still set) because the numeric variables get used
+ for other things in complicated expansions.
+
+. The default for rfc1413_query_timeout has been changed from 30s to 5s.
+
+. It is possible to use setclassresources() on some BSD OS to control the
+ resources used in pipe deliveries.
+
+. A new ACL modifier called add_header, which can be used with any verb.
+
+. More errors are detectable in retry rules.
+
+There are a number of other additions too.
+
+
+Version 4.60
+------------
+
+The documentation is up-to-date for the 4.60 release. Major new features since
+the 4.50 release are:
+
+. Support for SQLite.
+
+. Support for IGNOREQUOTA in LMTP.
+
+. Extensions to the "submission mode" features.
+
+. Support for Client SMTP Authorization (CSA).
+
+. Support for ratelimiting hosts and users.
+
+. New expansion items to help with the BATV "prvs" scheme.
+
+. A "match_ip" condition, that matches an IP address against a list.
+
+There are many more minor changes.
****
git://git.exim.org / users / heiko / exim.git / blobdiff