X-Git-Url: https://git.exim.org/exim.git/blobdiff_plain/ec4b68e5d820109e5954329013a911d4032bc4dc..2d8d625b2b96260d2517e59b896eb03e5c33aaf3:/src/src/configure.default diff --git a/src/src/configure.default b/src/src/configure.default index 0ccbbe855..ec60700df 100644 --- a/src/src/configure.default +++ b/src/src/configure.default @@ -56,7 +56,9 @@ domainlist local_domains = @ domainlist relay_to_domains = -hostlist relay_from_hosts = 127.0.0.1 +hostlist relay_from_hosts = localhost +# (We rely upon hostname resolution working for localhost, because the default +# uncommented configuration needs to work in IPv4-only environments.) # Most straightforward access control requirements can be obtained by # appropriate settings of the above options. In more complicated situations, @@ -91,12 +93,13 @@ hostlist relay_from_hosts = 127.0.0.1 # to any other host on the Internet. Such a setting commonly refers to a # complete local network as well as the localhost. For example: # -# hostlist relay_from_hosts = 127.0.0.1 : 192.168.0.0/16 +# hostlist relay_from_hosts = <; 127.0.0.1 ; ::1 ; 192.168.0.0/16 # # The "/16" is a bit mask (CIDR notation), not a number of hosts. Note that you # have to include 127.0.0.1 if you want to allow processes on your host to send # SMTP mail by using the loopback address. A number of MUAs use this method of -# sending mail. +# sending mail. Often, connections are made to "localhost", which might be ::1 +# on IPv6-enabled hosts. Do not forget CIDR for your IPv6 networks. # All three of these lists may contain many different kinds of item, including # wildcarded names, regular expressions, and file lookups. See the reference @@ -218,18 +221,26 @@ never_users = root host_lookup = * -# The settings below, which are actually the same as the defaults in the -# code, cause Exim to make RFC 1413 (ident) callbacks for all incoming SMTP -# calls. You can limit the hosts to which these calls are made, and/or change -# the timeout that is used. If you set the timeout to zero, all RFC 1413 calls -# are disabled. RFC 1413 calls are cheap and can provide useful information -# for tracing problem messages, but some hosts and firewalls have problems -# with them. This can result in a timeout instead of an immediate refused -# connection, leading to delays on starting up SMTP sessions. (The default was -# reduced from 30s to 5s for release 4.61.) +# The settings below cause Exim to make RFC 1413 (ident) callbacks +# for all incoming SMTP calls. You can limit the hosts to which these +# calls are made, and/or change the timeout that is used. If you set +# the timeout to zero, all RFC 1413 calls are disabled. RFC 1413 calls +# are cheap and can provide useful information for tracing problem +# messages, but some hosts and firewalls have problems with them. +# This can result in a timeout instead of an immediate refused +# connection, leading to delays on starting up SMTP sessions. +# (The default was reduced from 30s to 5s for release 4.61. and to +# disabled for release 4.86) +# +#rfc1413_hosts = * +#rfc1413_query_timeout = 5s + -rfc1413_hosts = * -rfc1413_query_timeout = 5s +# Enable an efficiency feature. We advertise the feature; clients +# may request to use it. For multi-recipient mails we then can +# reject or accept per-user after the message is received. +# +prdr_enable = true # By default, Exim expects all envelope addresses to be fully qualified, that @@ -245,6 +256,13 @@ rfc1413_query_timeout = 5s # and/or qualify_recipient (see above). +# Unless you run a high-volume site you probably want more logging +# detail than the default. Adjust to suit. + +log_selector = +smtp_protocol_error +smtp_syntax_error \ + +tls_certificate_verified + + # If you want Exim to support the "percent hack" for certain domains, # uncomment the following line and provide a list of domains. The "percent # hack" is the feature by which mail addressed to x%y@z (where z is one of @@ -474,6 +492,11 @@ acl_check_rcpt: acl_check_data: + # Deny if the message contains an overlong line. Per the standards + # we should never receive one such via SMTP. + # + deny condition = ${if > {$max_received_linelength}{998}} + # Deny if the message contains a virus. Before enabling this check, you # must install a virus scanner and set the av_scanner option above. # @@ -539,9 +562,26 @@ dnslookup: domains = ! +local_domains transport = remote_smtp ignore_target_hosts = 0.0.0.0 : 127.0.0.0/8 +# if ipv6-enabled then instead use: +# ignore_target_hosts = <; 0.0.0.0 ; 127.0.0.0/8 ; ::1 no_more +# This alternative router can be used when you want to send all mail to a +# server which handles DNS lookups for you; an ISP will typically run such +# a server for their customers. If you uncomment "smarthost" then you +# should comment out "dnslookup" above. Setting a real hostname in route_data +# wouldn't hurt either. + +# smarthost: +# driver = manualroute +# domains = ! +local_domains +# transport = remote_smtp +# route_data = MAIL.HOSTNAME.FOR.CENTRAL.SERVER.EXAMPLE +# ignore_target_hosts = <; 0.0.0.0 ; 127.0.0.0/8 ; ::1 +# no_more + + # The remaining routers handle addresses in the local domain(s), that is those # domains that are defined by "domainlist local_domains" above. @@ -649,9 +689,13 @@ begin transports # This transport is used for delivering messages over SMTP connections. +# Refuse to send any messsage with over-long lines, which could have +# been receved other than via SMTP. The use of message_size_limit to +# enforce this is a red herring. remote_smtp: driver = smtp + message_size_limit = ${if > {$max_received_linelength}{998} {1}{0}} # This transport is used for local delivery to user mailboxes in traditional