X-Git-Url: https://git.exim.org/exim.git/blobdiff_plain/ead05c2db0843fa927859b6d697400bc946c0d0b..1508acb8629a6ac1517ab524a9f29257a2335d5e:/doc/doc-docbook/spec.xfpt diff --git a/doc/doc-docbook/spec.xfpt b/doc/doc-docbook/spec.xfpt index 2f06f126f..c71dfb182 100644 --- a/doc/doc-docbook/spec.xfpt +++ b/doc/doc-docbook/spec.xfpt @@ -2991,6 +2991,26 @@ The specified sender is treated as if it were given as the argument to the preference to the address taken from the message. The caller of Exim must be a trusted user for the sender of a message to be set in this way. +.vitem &%-bmalware%&&~<&'filename'&> +.oindex "&%-bmalware%&" +.cindex "testing", "malware" +.cindex "malware scan test" +This debugging option causes Exim to scan the given file, +using the malware scanning framework. The option of &%av_scanner%& influences +this option, so if &%av_scanner%&'s value is dependent upon an expansion then +the expansion should have defaults which apply to this invocation. ACLs are +not invoked, so if &%av_scanner%& references an ACL variable then that variable +will never be populated and &%-bmalware%& will fail. + +Exim will have changed working directory before resolving the filename, so +using fully qualified pathnames is advisable. Exim will be running as the Exim +user when it tries to open the file, rather than as the invoking user. +This option requires admin privileges. + +The &%-bmalware%& option will not be extended to be more generally useful, +there are better tools for file-scanning. This option exists to help +administrators verify their Exim and AV scanner configuration. + .vitem &%-bnq%& .oindex "&%-bnq%&" .cindex "address qualification, suppressing" @@ -3251,26 +3271,6 @@ above concerning senders and qualification do not apply. In this situation, Exim behaves in exactly the same way as it does when receiving a message via the listening daemon. -.vitem &%-bmalware%&&~<&'filename'&> -.oindex "&%-bmalware%&" -.cindex "testing", "malware" -.cindex "malware scan test" -This debugging option causes Exim to scan the given file, -using the malware scanning framework. The option of &%av_scanner%& influences -this option, so if &%av_scanner%&'s value is dependent upon an expansion then -the expansion should have defaults which apply to this invocation. ACLs are -not invoked, so if &%av_scanner%& references an ACL variable then that variable -will never be populated and &%-bmalware%& will fail. - -Exim will have changed working directory before resolving the filename, so -using fully qualified pathnames is advisable. Exim will be running as the Exim -user when it tries to open the file, rather than as the invoking user. -This option requires admin privileges. - -The &%-bmalware%& option will not be extended to be more generally useful, -there are better tools for file-scanning. This option exists to help -administrators verify their Exim and AV scanner configuration. - .vitem &%-bt%& .oindex "&%-bt%&" .cindex "testing" "addresses" @@ -6026,16 +6026,16 @@ that it implements the details of the specific authentication mechanism, i.e. PLAIN or LOGIN. The &%server_advertise_condition%& setting controls when Exim offers authentication to clients; in the examples, this is only when TLS or SSL has been started, so to enable the authenticators you also -need to add support for TLS as described in &<>&. +need to add support for TLS as described in section &<>&. The &%server_condition%& setting defines how to verify that the username and password are correct. In the examples it just produces an error message. To make the authenticators work, you can use a string expansion -expression like one of the examples in &<>&. +expression like one of the examples in chapter &<>&. Beware that the sequence of the parameters to PLAIN and LOGIN differ; the -usercode and password are in different positions. &<>& -covers both. +usercode and password are in different positions. +Chapter &<>& covers both. .ecindex IIDconfiwal @@ -15697,19 +15697,52 @@ by Thunderbird, while GnuTLS was suggesting 2432 bits as normal. If you prefer more security and are willing to break some clients, raise this number. + +Note that the value passed to GnuTLS for *generating* a new prime may be a +little less than this figure, because GnuTLS is inexact and may produce a +larger prime than requested. .wen .option tls_dhparam main string&!! unset .cindex "TLS" "D-H parameters for server" -The value of this option is expanded, and must then be the absolute path to -a file which contains the server's DH parameter values. -This is used only for OpenSSL. When Exim is linked with GnuTLS, this option is -ignored. See section &<>& for further details. - .new -If the DH bit-count from loading the file is greater than tls_dh_max_bits then -it will be ignored. +The value of this option is expanded and indicates the source of DH parameters +to be used by Exim. + +If it is a filename starting with a &`/`&, then it names a file from which DH +parameters should be loaded. If the file exists, it should hold a PEM-encoded +PKCS#3 representation of the DH prime. If the file does not exist, for +OpenSSL it is an error. For GnuTLS, Exim will attempt to create the file and +fill it with a generated DH prime. For OpenSSL, if the DH bit-count from +loading the file is greater than &%tls_dh_max_bits$& then it will be ignored, +and treated as though the &%tls_dhparam%& were set to "none". + +If this option expands to the string "none", then no DH parameters will be +loaded by Exim. + +If this option expands to the string "historic" and Exim is using GnuTLS, then +Exim will attempt to load a file from inside the spool directory. If the file +does not exist, Exim will attempt to create it. +See section &<>& for further details. + +If Exim is using OpenSSL and this option is empty or unset, then Exim will load +a default DH prime; the default is the 2048 bit prime described in section +2.2 of RFC 5114, "2048-bit MODP Group with 224-bit Prime Order Subgroup", which +in IKE is assigned number 23. + +Otherwise, the option must expand to the name used by Exim for any of a number +of DH primes specified in RFC 2409, RFC 3526 and RFC 5114. As names, Exim uses +"ike" followed by the number used by IKE, of "default" which corresponds to +"ike23". + +The available primes are: +&`ike1`&, &`ike2`&, &`ike5`&, +&`ike14`&, &`ike15`&, &`ike16`&, &`ike17`&, &`ike18`&, +&`ike22`&, &`ike23`& (aka &`default`&) and &`ike24`&. + +Some of these will be too small to be accepted by clients. +Some may be too large to be accepted by clients. .wen @@ -24996,12 +25029,8 @@ There are some differences in usage when using GnuTLS instead of OpenSSL: The &%tls_verify_certificates%& option must contain the name of a file, not the name of a directory (for OpenSSL it can be either). .next -The &%tls_dhparam%& option is ignored, because early versions of GnuTLS had no -facility for varying its Diffie-Hellman parameters. .new -Since then, the GnuTLS support has been updated to generate parameters upon -demand, keeping them in the spool directory. See &<>& for -details. +The default value for &%tls_dhparam%& differs for historical reasons. .wen .next .vindex "&$tls_peerdn$&" @@ -25032,6 +25061,12 @@ implementation, then patches are welcome. .section "GnuTLS parameter computation" "SECTgnutlsparam" .new +This section only applies if &%tls_dhparam%& is set to &`historic`& or to +an explicit path; if the latter, then the text about generation still applies, +but not the chosen filename. +By default, as of Exim 4.80 a hard-coded D-H prime is used. +See the documentation of &%tls_dhparam%& for more information. + GnuTLS uses D-H parameters that may take a substantial amount of time to compute. It is unreasonable to re-compute them for every TLS session. Therefore, Exim keeps this data in a file in its spool directory, called @@ -25047,6 +25082,10 @@ place, new Exim processes immediately start using it. For maximum security, the parameters that are stored in this file should be recalculated periodically, the frequency depending on your paranoia level. +If you are avoiding using the fixed D-H primes published in RFCs, then you +are concerned about some advanced attacks and will wish to do this; if you do +not regenerate then you might as well stick to the standard primes. + Arranging this is easy in principle; just delete the file when you want new values to be computed. However, there may be a problem. The calculation of new parameters needs random numbers, and these are obtained from &_/dev/random_&. @@ -25070,6 +25109,10 @@ renaming. The relevant commands are something like this: # chown exim:exim new-params # chmod 0600 new-params # certtool --generate-dh-params --bits 2236 >>new-params +# openssl dhparam -noout -text -in new-params | head +[ check the first line, make sure it's not more than 2236; + if it is, then go back to the start ("rm") and repeat + until the size generated is at most the size requested ] # chmod 0400 new-params # mv new-params gnutls-params-2236 .endd @@ -25092,6 +25135,12 @@ The filename and bits used will change as the GnuTLS maintainers change the value for their parameter &`GNUTLS_SEC_PARAM_NORMAL`&, as clamped by &%tls_dh_max_bits%&. At the time of writing (mid 2012), GnuTLS 2.12 recommends 2432 bits, while NSS is limited to 2236 bits. + +In fact, the requested value will be *lower* than &%tls_dh_max_bits%&, to +increase the chance of the generated prime actually being within acceptable +bounds, as GnuTLS has been observed to overshoot. Note the check step in the +procedure above. There is no sane procedure available to Exim to double-check +the size of the generated prime, so it might still be too large. .wen @@ -25270,13 +25319,24 @@ this). There is one other option that may be needed in other situations. If tls_dhparam = /some/file/name .endd is set, the SSL library is initialized for the use of Diffie-Hellman ciphers -with the parameters contained in the file. This increases the set of cipher -suites that the server supports. See the command +with the parameters contained in the file. +.new +Set this to &`none`& to disable use of DH entirely, by making no prime +available: +.code +tls_dhparam = none +.endd +This may also be set to a string identifying a standard prime to be used for +DH; if it is set to &`default`& or, for OpenSSL, is unset, then the prime +used is &`ike23`&. There are a few standard primes available, see the +documetnation for &%tls_dhparam%& for the complete list. + +See the command .code openssl dhparam .endd -for a way of generating this data. At present, &%tls_dhparam%& is used only -when Exim is linked with OpenSSL. It is ignored if GnuTLS is being used. +for a way of generating file data. +.wen The strings supplied for these three options are expanded every time a client host connects. It is therefore possible to use different certificates and keys