X-Git-Url: https://git.exim.org/exim.git/blobdiff_plain/9bdd29ad5c5d394229753b114f6f288893f616f4..c0c4d23c07e2356baae2bd2c6d72339db117b9e6:/doc/doc-txt/experimental-spec.txt?ds=sidebyside diff --git a/doc/doc-txt/experimental-spec.txt b/doc/doc-txt/experimental-spec.txt index a5024d827..f21609662 100644 --- a/doc/doc-txt/experimental-spec.txt +++ b/doc/doc-txt/experimental-spec.txt @@ -452,15 +452,21 @@ which the spf condition should succeed. Valid strings are: This means the queried domain has published a SPF record, but wants to allow outside servers to send mail under its domain as well. - o err_perm This indicates a syntax error in the SPF - record of the queried domain. This should be - treated like "none". - o err_temp This indicates a temporary error during all + This should be treated like "none". + o permerror This indicates a syntax error in the SPF + record of the queried domain. You may deny + messages when this occurs. (Changed in 4.83) + o temperror This indicates a temporary error during all processing, including Exim's SPF processing. You may defer messages when this occurs. + (Changed in 4.83) + o err_temp Same as permerror, deprecated in 4.83, will be + removed in a future release. + o err_perm Same as temperror, deprecated in 4.83, will be + removed in a future release. You can prefix each string with an exclamation mark to invert -is meaning, for example "!fail" will match all results but +its meaning, for example "!fail" will match all results but "fail". The string list is evaluated left-to-right, in a short-circuit fashion. When a string matches the outcome of the SPF check, the condition succeeds. If none of the listed @@ -510,8 +516,8 @@ variables. $spf_result This contains the outcome of the SPF check in string form, - one of pass, fail, softfail, none, neutral, err_perm or - err_temp. + one of pass, fail, softfail, none, neutral, permerror or + temperror. $spf_smtp_comment This contains a string that can be used in a SMTP response @@ -773,7 +779,7 @@ fails. Of course, you can also use any other lookup method that Exim supports, including LDAP, Postgres, MySQL, etc, as long as the -result is a list of colon-separated strings; +result is a list of colon-separated strings. Several expansion variables are set before the DATA ACL is processed, and you can use them in this ACL. The following @@ -781,7 +787,10 @@ expansion variables are available: o $dmarc_status This is a one word status indicating what the DMARC library - thinks of the email. + thinks of the email. It is a combination of the results of + DMARC record lookup and the SPF/DKIM/DMARC processing results + (if a DMARC record was found). The actual policy declared + in the DMARC record is in a separate expansion variable. o $dmarc_status_text This is a slightly longer, human readable status. @@ -790,6 +799,11 @@ expansion variables are available: This is the domain which DMARC used to look up the DMARC policy record. + o $dmarc_domain_policy + This is the policy declared in the DMARC record. Valid values + are "none", "reject" and "quarantine". It is blank when there + is any error, including no DMARC record. + o $dmarc_ar_header This is the entire Authentication-Results header which you can add using an add_header modifier. @@ -825,6 +839,9 @@ b. Configure, somewhere before the DATA ACL, the control option to warn !domains = +screwed_up_dmarc_records control = dmarc_enable_forensic + warn condition = (lookup if destined to mailing list) + set acl_m_mailing_list = 1 + (DATA ACL) warn dmarc_status = accept : none : off !authenticated = * @@ -840,6 +857,10 @@ b. Configure, somewhere before the DATA ACL, the control option to set $acl_m_quarantine = 1 # Do something in a transport with this flag variable + deny condition = ${if eq{$dmarc_domain_policy}{reject}} + condition = ${if eq{$acl_m_mailing_list}{1}} + message = Messages from $dmarc_used_domain break mailing lists + deny dmarc_status = reject !authenticated = * message = Message from $domain_used_domain failed sender's DMARC policy, REJECT @@ -912,7 +933,7 @@ log failures of remote hosts. It is executed only when exim has attempted to deliver a message to a remote host and failed due to an error which doesn't seem to be related to the individual message, sender, or recipient address. -See section 45.2 of the exim documentation for more details on how +See section 47.2 of the exim documentation for more details on how this is determined. Example: @@ -1015,6 +1036,131 @@ Where SPAMMER_SET is a macro and it is defined as set acl_c_spam_host = ${lookup redis{GET...}} +Proxy Protocol Support +-------------------------------------------------------------- + +Exim now has Experimental "Proxy Protocol" support. It was built on +specifications from: +http://haproxy.1wt.eu/download/1.5/doc/proxy-protocol.txt + +The purpose of this function is so that an application load balancer, +such as HAProxy, can sit in front of several Exim servers and Exim +will log the IP that is connecting to the proxy server instead of +the IP of the proxy server when it connects to Exim. It resets the +$sender_address_host and $sender_address_port to the IP:port of the +connection to the proxy. It also re-queries the DNS information for +this new IP address so that the original sender's hostname and IP +get logged in the Exim logfile. There is no logging if a host passes or +fails Proxy Protocol negotiation, but it can easily be determined and +recorded in an ACL (example is below). + +1. To compile Exim with Proxy Protocol support, put this in +Local/Makefile: + +EXPERIMENTAL_PROXY=yes + +2. Global configuration settings: + +proxy_required_hosts = HOSTLIST + +The proxy_required_hosts option will require any IP in that hostlist +to use Proxy Protocol. The specification of Proxy Protocol is very +strict, and if proxy negotiation fails, Exim will not allow any SMTP +command other than QUIT. (See end of this section for an example.) +The option is expanded when used, so it can be a hostlist as well as +string of IP addresses. Since it is expanded, specifying an alternate +separator is supported for ease of use with IPv6 addresses. + +To log the IP of the proxy in the incoming logline, add: + log_selector = +proxy + +A default incoming logline (wrapped for appearance) will look like this: + + 2013-11-04 09:25:06 1VdNti-0001OY-1V <= me@example.net + H=mail.example.net [1.2.3.4] P=esmtp S=433 + +With the log selector enabled, an email that was proxied through a +Proxy Protocol server at 192.168.1.2 will look like this: + + 2013-11-04 09:25:06 1VdNti-0001OY-1V <= me@example.net + H=mail.example.net [1.2.3.4] P=esmtp PRX=192.168.1.2 S=433 + +3. In the ACL's the following expansion variables are available. + +proxy_host_address The (internal) src IP of the proxy server + making the connection to the Exim server. +proxy_host_port The (internal) src port the proxy server is + using to connect to the Exim server. +proxy_target_address The dest (public) IP of the remote host to + the proxy server. +proxy_target_port The dest port the remote host is using to + connect to the proxy server. +proxy_session Boolean, yes/no, the connected host is required + to use Proxy Protocol. + +There is no expansion for a failed proxy session, however you can detect +it by checking if $proxy_session is true but $proxy_host is empty. As +an example, in my connect ACL, I have: + + warn condition = ${if and{ {bool{$proxy_session}} \ + {eq{$proxy_host_address}{}} } } + log_message = Failed required proxy protocol negotiation \ + from $sender_host_name [$sender_host_address] + + warn condition = ${if and{ {bool{$proxy_session}} \ + {!eq{$proxy_host_address}{}} } } + # But don't log health probes from the proxy itself + condition = ${if eq{$proxy_host_address}{$sender_host_address} \ + {false}{true}} + log_message = Successfully proxied from $sender_host_name \ + [$sender_host_address] through proxy protocol \ + host $proxy_host_address + + # Possibly more clear + warn logwrite = Remote Source Address: $sender_host_address:$sender_host_port + logwrite = Proxy Target Address: $proxy_target_address:$proxy_target_port + logwrite = Proxy Internal Address: $proxy_host_address:$proxy_host_port + logwrite = Internal Server Address: $received_ip_address:$received_port + + +4. Runtime issues to be aware of: + - Since the real connections are all coming from your proxy, and the + per host connection tracking is done before Proxy Protocol is + evaluated, smtp_accept_max_per_host must be set high enough to + handle all of the parallel volume you expect per inbound proxy. + - The proxy has 3 seconds (hard-coded in the source code) to send the + required Proxy Protocol header after it connects. If it does not, + the response to any commands will be: + "503 Command refused, required Proxy negotiation failed" + - If the incoming connection is configured in Exim to be a Proxy + Protocol host, but the proxy is not sending the header, the banner + does not get sent until the timeout occurs. If the sending host + sent any input (before the banner), this causes a standard Exim + synchronization error (i.e. trying to pipeline before PIPELINING + was advertised). + - This is not advised, but is mentioned for completeness if you have + a specific internal configuration that you want this: If the Exim + server only has an internal IP address and no other machines in your + organization will connect to it to try to send email, you may + simply set the hostlist to "*", however, this will prevent local + mail programs from working because that would require mail from + localhost to use Proxy Protocol. Again, not advised! + +5. Example of a refused connection because the Proxy Protocol header was +not sent from a host configured to use Proxy Protocol. In the example, +the 3 second timeout occurred (when a Proxy Protocol banner should have +been sent), the banner was displayed to the user, but all commands are +rejected except for QUIT: + +# nc mail.example.net 25 +220-mail.example.net, ESMTP Exim 4.82+proxy, Mon, 04 Nov 2013 10:45:59 +220 -0800 RFC's enforced +EHLO localhost +503 Command refused, required Proxy negotiation failed +QUIT +221 mail.example.net closing connection + + -------------------------------------------------------------- End of file