X-Git-Url: https://git.exim.org/exim.git/blobdiff_plain/8b417f2c8e0df074cbb139081e5f1fb7992946dd..2e0c1448cf7e5612a17b4ff09fe7a05235cce7f2:/doc/doc-txt/ChangeLog diff --git a/doc/doc-txt/ChangeLog b/doc/doc-txt/ChangeLog index 18e8d1ff8..d8272ab92 100644 --- a/doc/doc-txt/ChangeLog +++ b/doc/doc-txt/ChangeLog @@ -1,4 +1,4 @@ -$Cambridge: exim/doc/doc-txt/ChangeLog,v 1.104 2005/03/29 14:53:09 ph10 Exp $ +$Cambridge: exim/doc/doc-txt/ChangeLog,v 1.127 2005/04/27 13:29:32 ph10 Exp $ Change log file for Exim from version 4.21 ------------------------------------------- @@ -38,7 +38,7 @@ PH/04 Change 4.11/85 fixed an obscure bug concerned with addresses that are "previously delivered" was not happening when checking to see if an address could be batched with a previous (undelivered) one; under certain circumstances this could lead to multiple deliveries to the same - address. A one-line patch to add the appropriate test fixes the bug. + address. PH/05 Renamed the macro SOCKLEN_T as EXIM_SOCKLEN_T because AIX uses SOCKLEN_T in its include files, and this causes problems building Exim. @@ -99,6 +99,156 @@ PH/17 The API for radiusclient changed at release 0.4.0. Unfortunately, the PH/18 Installed Lars Mainka's patch for the support of CRL collections in files or directories, for OpenSSL. +PH/19 When an Exim process that is running as root has to create an Exim log + file, it does so in a subprocess that runs as exim:exim so as to get the + ownership right at creation (otherwise, other Exim processes might see + the file with the wrong ownership). There was no test for failure of this + fork() call, which would lead to the process getting stuck as it waited + for a non-existent subprocess. Forks do occasionally fail when resources + run out. I reviewed all the other calls to fork(); they all seem to check + for failure. + +PH/20 When checking for unexpected SMTP input at connect time (before writing + the banner), Exim was not dealing correctly with a non-positive return + from the read() function. If the client had disconnected by this time, + the result was a log entry for a synchronization error with an empty + string after "input=" when read() returned zero. If read() returned -1 + (an event I could not check), uninitialized data bytes were printed. + There were reports of junk text (parts of files, etc) appearing after + "input=". + +PH/21 Added acl_not_smtp_mime to allow for MIME scanning for non-SMTP messages. + +PH/22 Added support for macro redefinition, and (re)definition in between + driver and ACL definitions. + +PH/23 The cyrus_sasl authenticator was expanding server_hostname, but then + forgetting to use the resulting value; it was using the unexpanded value. + +PH/24 The cyrus_sasl authenticator was advertising mechanisms for which it + hadn't been configured. The fix is from Juergen Kreileder, who + understands it better than I do: + + "Here's what I see happening with three configured cyrus_sasl + authenticators configured (plain, login, cram-md5): + + On startup auth_cyrus_sasl_init() gets called for each of these. + This means three calls to sasl_listmech() without a specified mech_list. + => SASL tests which mechs of all available mechs actually work + => three warnings about OTP not working + => the returned list contains: plain, login, cram-md5, digest-md5, ... + + With the patch, sasl_listmech() also gets called three times. But now + SASL's mech_list option is set to the server_mech specified in the the + authenticator. Or in other words, the answer from sasl_listmech() + gets limited to just the mech you're testing for (which is different + for each call.) + => the return list contains just 'plain' or 'login', 'cram-md5' or + nothing depending on the value of ob->server_mech. + + I've just tested the patch: Authentication still works fine, + unavailable mechs specified in the exim configuration are still + caught, and the auth.log warnings about OTP are gone." + +PH/25 When debugging is enabled, the contents of the command line are added + to the debugging output, even when log_selector=+arguments is not + specified. + +PH/26 Change scripts/os-type so that when "uname -s" returns just "GNU", the + answer is "GNU", and only if the return is "GNU/something" is the answer + "Linux". + +PH/27 $acl_verify_message is now set immediately after the failure of a + verification in an ACL, and so is available in subsequent modifiers. In + particular, the message can be preserved by coding like this: + + warn !verify = sender + set acl_m0 = $acl_verify_message + + Previously, $acl_verify_message was set only while expanding "message" + and "log_message" when a very denied access. + +PH/28 Modified OS/os.c-Linux with + + -#ifndef OS_LOAD_AVERAGE + +#if !defined(OS_LOAD_AVERAGE) && defined(__linux__) + + to make Exim compile on kfreebsd-gnu. (I'm totally confused about the + nomenclature these days.) + +PH/29 Installed patch from the Sieve maintainer that adds the options + sieve_useraddress and sieve_subaddress to the redirect router. + +PH/30 In these circumstances: + . Two addresses routed to the same list of hosts; + . First host does not offer TLS; + . First host accepts first address; + . First host gives temporary error to second address; + . Second host offers TLS and a TLS session is established; + . Second host accepts second address. + Exim incorrectly logged both deliveries with the TLS parameters (cipher + and peerdn, if requested) that were in fact used only for the second + address. + +PH/31 When doing a callout as part of verifying an address, Exim was not paying + attention to any local part prefix or suffix that was matched by the + router that accepted the address. It now behaves in the same way as it + does for delivery: the affixes are removed from the local part unless + rcpt_include_affixes is set on the transport. + +PH/32 Add the sender address, as F=<...>, to the log line when logging a + timeout during the DATA phase of an incoming message. + +PH/33 Sieve envelope tests were broken for match types other than :is. I have + applied a patch sanctioned by the Sieve maintainer. + +PH/34 Change 4.50/80 broke Exim in that it could no longer handle cases where + the uid or gid is negative. A case of a negative gid caused this to be + noticed. The fix allows for either to be negative. + +PH/35 ACL_WHERE_MIME is now declared unconditionally, to avoid too much code + clutter, but the tables that are indexed by ACL_WHERE_xxx values had been + overlooked. + +PH/36 The change PH/12 above was broken. Fixed it. + +PH/37 Exim used to check for duplicate addresses in the middle of routing, on + the grounds that routing the same address twice would always produce the + same answer. This might have been true once, but it is certainly no + longer true now. Routing a child address may depend on the previous + routing that produced that child. Some complicated redirection strategies + went wrong when messages had multiple recipients, and made Exim's + behaviour dependent on the order in which the addresses were given. + + I have moved the duplicate checking until after the routing is complete. + Exim scans the addresses that are assigned to local and remote + transports, and removes any duplicates. This means that more work will be + done, as duplicates will always all be routed, but duplicates are + presumably rare, so I don't expect this is of any significance. + + For deliveries to pipes, files, and autoreplies, the duplicate checking + still happens during the routing process, since they are not going to be + routed further. + +PH/38 Installed a patch from Ian Freislich, with the agreement of Tom Kistner. + It corrects a timeout issue with spamd. This is Ian's comment: "The + background is that sometimes spamd either never reads data from a + connection it has accepted, or it never writes response data. The exiscan + spam.[ch] uses a 3600 second timeout on spamd socket reads, further, it + blindly assumes that writes won't block so it may never time out." + +PH/39 Allow G after quota size as well as K and M. + +PH/40 The value set for $authenticated_id in an authenticator may not contain + binary zeroes or newlines because the value is written to log lines and + to spool files. There was no check on this. Now the value is run through + the string_printing() function so that such characters are converted to + printable escape sequences. + +PH/41 $message_linecount is a new variable that contains the total number of + lines in the message. Compare $body_linecount, which is the count for the + body only. + A note about Exim versions 4.44 and 4.50 ----------------------------------------