X-Git-Url: https://git.exim.org/exim.git/blobdiff_plain/65e061b76867a9ea7aeeb535341b790b90ae6c21..0f1a8658daf8689f0ef0afbb11d0cb589447a57d:/doc/doc-docbook/spec.xfpt

diff --git a/doc/doc-docbook/spec.xfpt b/doc/doc-docbook/spec.xfpt
index 7816bc26d..35f3eb80e 100644
--- a/doc/doc-docbook/spec.xfpt
+++ b/doc/doc-docbook/spec.xfpt
@@ -12793,6 +12793,15 @@ argument, that is, the text that follows the command name, with leading white
 space removed. Following the introduction of &$smtp_command$&, this variable is
 somewhat redundant, but is retained for backwards compatibility.
 
+.new
+.vitem &$smtp_command_history$&
+.cindex SMTP "command history"
+.vindex "&$smtp_command_history$&"
+A comma-separated list (with no whitespace) of the most-recent SMTP commands
+received, in time-order left to right.  Only a limited number of commands
+are remembered.
+.wen
+
 .vitem &$smtp_count_at_connection_start$&
 .vindex "&$smtp_count_at_connection_start$&"
 This variable is set greater than zero only in processes spawned by the Exim
@@ -19469,6 +19478,10 @@ instead of TRY_AGAIN. That is why the default action is to try a DNS
 lookup first. Only if that gives a definite &"no such host"& is the local
 function called.
 
+&*Compatibility*&: From Exim 4.85 until fixed for 4.90, there was an
+inadvertent constraint that a transport name as an option had to be the last
+option specified.
+
 
 
 If no IP address for a host can be found, what happens is controlled by the
@@ -22128,10 +22141,14 @@ the obvious value which users understand most easily.
 
 The value of the option is expanded, and must then be a numerical value
 (decimal point allowed), optionally followed by one of the letters K, M, or G,
-for kilobytes, megabytes, or gigabytes. If Exim is running on a system with
+for kilobytes, megabytes, or gigabytes, optionally followed by a slash
+and further option modifiers. If Exim is running on a system with
 large file support (Linux and FreeBSD have this), mailboxes larger than 2G can
 be handled.
 
+The option modifier &%no_check%& can be used to force delivery even if the over
+quota condition is met. The quota gets updated as usual.
+
 &*Note*&: A value of zero is interpreted as &"no quota"&.
 
 The expansion happens while Exim is running as root, before it changes uid for
@@ -22166,6 +22183,8 @@ can only be used if &%quota%& is also set. The value is expanded; an expansion
 failure causes delivery to be deferred. A value of zero is interpreted as
 &"no quota"&.
 
+The option modifier &%no_check%& can be used to force delivery even if the over
+quota condition is met. The quota gets updated as usual.
 
 .option quota_is_inclusive appendfile boolean true
 See &%quota%& above.
@@ -36099,6 +36118,7 @@ selection marked by asterisks:
 &` incoming_interface         `&  local interface on <= and => lines
 &` incoming_port              `&  remote port on <= lines
 &`*lost_incoming_connection   `&  as it says (includes timeouts)
+&` millisec                   `&  millisecond timestamps and QT,DT,D times
 &` outgoing_interface         `&  local interface on => lines
 &` outgoing_port              `&  add remote port to => lines
 &`*queue_run                  `&  start and end queue runs
@@ -36188,6 +36208,8 @@ process is started because &%queue_only%& is set or &%-odq%& was used.
 .cindex "log" "delivery duration"
 &%deliver_time%&: For each delivery, the amount of real time it has taken to
 perform the actual delivery is logged as DT=<&'time'&>, for example, &`DT=1s`&.
+If millisecond logging is enabled, short times will be shown with greater
+precision, eg. &`DT=0.304`&.
 .next
 .cindex "log" "message size on delivery"
 .cindex "size" "of message"
@@ -36263,6 +36285,14 @@ important with the widening use of NAT (see RFC 2505).
 &%lost_incoming_connection%&: A log line is written when an incoming SMTP
 connection is unexpectedly dropped.
 .next
+.new
+.cindex "log" "millisecond timestamps"
+.cindex millisecond logging
+.cindex timstamps "millisecond, in logs"
+&%millisec%&: Timestamps have a period and three decimal places of finer granularity
+appended to the seconds value.
+.wen
+.next
 .cindex "log" "outgoing interface"
 .cindex "log" "local interface"
 .cindex "log" "local address and port"
@@ -36301,6 +36331,8 @@ includes reception time as well as the delivery time for the current address.
 This means that it may be longer than the difference between the arrival and
 delivery log line times, because the arrival log line is not written until the
 message has been successfully received.
+If millisecond logging is enabled, short times will be shown with greater
+precision, eg. &`QT=1.578s`&.
 .next
 &%queue_time_overall%&: The amount of time the message has been in the queue on
 the local host is logged as QT=<&'time'&> on &"Completed"& lines, for