X-Git-Url: https://git.exim.org/exim.git/blobdiff_plain/5d5ad9fb16a2511ff2e0e7d4528d399f06f608da..b0e63c7efdc2133c61545b051042d3617ecd2bbd:/doc/doc-docbook/spec.xfpt

diff --git a/doc/doc-docbook/spec.xfpt b/doc/doc-docbook/spec.xfpt
index add3a532e..dc8f5cc4d 100644
--- a/doc/doc-docbook/spec.xfpt
+++ b/doc/doc-docbook/spec.xfpt
@@ -24831,7 +24831,7 @@ Exim, and each argument is separately expanded, as described in section
 No part of the resulting command may be tainted.
 
 
-.option environment pipe string&!! unset
+.option environment pipe "string list&!!" unset
 .cindex "&(pipe)& transport" "environment for command"
 .cindex "environment" "&(pipe)& transport"
 This option is used to add additional variables to the environment in which the
@@ -35335,9 +35335,10 @@ The arguments are as follows:
 (the -D file). The file is open for reading and writing, but updating it is not
 recommended. &*Warning*&: You must &'not'& close this file descriptor.
 
-The descriptor is positioned at character 19 of the file, which is the first
-character of the body itself, because the first 19 characters are the message
-id followed by &`-D`& and a newline. If you rewind the file, you should use the
+The descriptor is positioned at character 26 of the file, which is the first
+character of the body itself, because the first 26 characters (19 characters
+before Exim  4.97) are the message id followed by &`-D`& and a newline.
+If you rewind the file, you should use the
 macro SPOOL_DATA_START_OFFSET to reset to the start of the data, just in
 case this changes in some future version.
 .next
@@ -39096,7 +39097,7 @@ selection marked by asterisks:
 .irow &`tls_peerdn`&			&nbsp; "TLS peer DN on <= and => lines"
 .irow &`tls_resumption`&		&nbsp; "append * to cipher field"
 .irow &`tls_sni`&			&nbsp; "TLS SNI on <= lines"
-.irow &`unknown_in_list`&		&nbsp; "DNS lookup failed in list match"
+.irow &`unknown_in_list`&		&nbsp; "lookup failed in list match"
 .irow &`all`&				&nbsp; "&*all of the above*&"
 .endtable
 See also the &%slow_lookup_log%& main configuration option,
@@ -39515,7 +39516,8 @@ added to the log line, preceded by SNI=.
 .next
 .cindex "log" "DNS failure in list"
 &%unknown_in_list%&: This setting causes a log entry to be written when the
-result of a list match is failure because a DNS lookup failed.
+result of a list match is failure because a DNS lookup failed, or because
+a bad IP address was in the list.
 .endlist
 
 
@@ -41710,7 +41712,7 @@ variables here.
 .option dkim_sign_headers smtp string&!! "see below"
 If set, this option must expand to a colon-separated
 list of header names.
-Headers with these names, or the absence or such a header, will be included
+Headers with these names, or the absence of such a header, will be included
 in the message signature.
 When unspecified, the header names listed in RFC4871 will be used,
 whether or not each header is present in the message.